Wayne-Dalton 5120, 5140 installation instructions TorqueMaster Spring Tube, Center Bracket Bushing

Page 19

 

 

 

15

TorqueMaster® Spring Tube

 

Tools Needed:

TorqueMaster® springs come lubricated

None

and pre-assembled inside the

TorqueMaster® spring tube. To install, lay

 

 

the TorqueMaster® spring tube on the

 

floor (inside garage) in front of the door

 

with the labeled end to the left.

 

 

 

TorqueMaster®

INSTALLATION

 

 

 

Spring Tube

 

 

LABELED END

 

 

 

 

 

16

Center Bracket Bushing

 

 

CENTER

 

 

 

BRACKET

 

 

 

ASSEMBLY

 

 

 

 

Tools Needed:

NOTE: If you are installing the idrive®

 

 

None

opener on your garage door, skip this

 

 

step and continue with Step 17.

 

 

 

 

 

 

NOTE: If you are not installing an idrive®

 

 

 

opener on your garage door, you must

TorqueMaster®

 

 

install the center bracket bushing

 

 

Spring Tube

 

 

assembly. Follow these instructions for

 

 

 

non-idrive®operated garage doors.

 

 

 

NOTE: If you are installing a

 

 

 

DoorMaster™ opener, see optional

TorqueMaster®

 

 

DoorMaster™ Bracket installations on

 

 

page 31, Figure A.

Spring Tube

 

 

 

 

 

Being cam shaped the center bracket

 

 

 

bushing only fits one way.

 

 

 

Slide the center bracket assembly

 

 

 

towards the center of the TorqueMaster®

 

 

 

spring tube, from the right side as

 

 

 

shown.

CENTER

 

 

 

 

 

NOTE: Upon completion of this step,

BRACKET

 

 

BUSHING

 

 

continue with Step 18.

 

 

 

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer.

19

To find your Wayne-Dalton dealer; refer to your local yellow pages / business listings or go to Find a dealer area online at www.wayne-dalton.com

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 5120 Table of Contents Package Contents Door Section Identification Tools Required Winding bars can cause Spring energy to be released Torsion Spring RemovalFor Standard Lift Failure to use approvedHead will be plugged Using an electric drill HighCounter cover when counting Bracket will always have a drive gearRemoval TorqueMaster SpringRemoving the Old Door Extension Spring RemovalPreparing the Opening Attaching Quick Install Flag InstallationAngle to Vertical Track Horizontal Angle Installing Q.I. Jamb BracketsBottom Section DrumsStacking Sections Vertical TrackBar Top BracketsOperator Bracket Bar AsymmetricalTop Section Remove the nail that was temporarily Tools Needed To install horizontal track, placeTo the slot in the flagangle using Portion of horizontal track down toCenter Bracket Bushing TorqueMaster Spring TubeRight hand end of the TorqueMaster Idrive InstallationPlug the motor power cord into Opener Garage looking outCable Drum Installation End Brackets Drive Gear InstallationSecuring Center Bracket Assembly Counter InstallationPositioning Support Bracket Mounting Disconnect Attaching Disconnect CablesHandle Bracket Attaching Disconnect Handle Onto vertical Track can Cable AdjustmentsSecuring Door Failure to place vice clampsWinding Bolt Rotation Setting Spring TensionRear Support Drum Wrap InstallationOr door stop too tightly against face Adjustments to the springsInstallation Instructions Parallel with doorSide Lock Sold Separately Pull Rope Step Plate Sold SeperatelyTrolley to operator bracket Determine the Wayne-DaltonTrack radius being used Appropriate 1/2 1 room permitting above of the highTrolley Installation for Low Headroom Suitable mounting Trolley OperatorOpens if Photoelectric EYE System Operator RailCleaning Your Garage Door CleaningPainting Painting MaintenanceLimited Warranty Models 5120
Top Page Image Contents