Wayne-Dalton 5140 Idrive Installation, Garage looking out, Right hand end of the TorqueMaster

Page 20

17

idrive® Installation

 

 

 

 

 

Tools Needed:

NOTE: See idrive® main installation and

 

 

 

owners manual for idrive® parts.

 

 

None

IMPORTANT: Right and left hand

 

 

 

 

 

 

is always determined from inside

Left Hand Side

 

 

the garage looking out.

TorqueMaster® Spring Tube

 

 

 

and Bearing profiles aligned

Motor

 

Lay the TorqueMaster® spring tube on

 

 

 

 

 

the floor (inside garage) in front of the

 

 

 

door with the labeled end to the left.

 

 

 

Look into the opener’s left side to

Right Hand End

 

 

ensure the left hand bearing and the

 

 

internal (black) sleeve are aligned with

of TorqueMaster®

 

 

Spring Tube

 

 

the TorqueMaster® spring tube profile.

 

 

 

 

 

IMPORTANT: Hold Opener by the

 

 

 

main body. Do NOT hold by the

 

 

 

Motor.

 

 

 

NOTE: Opener will not slide over the

 

 

 

TorqueMaster® spring tube label.

 

 

 

Attempting to slide opener over the left

 

 

 

end of the TorqueMaster® spring tube

 

 

 

can damage the internal electronics.

 

Right Hand Side

 

 

 

 

Once aligned, slide the opener onto the

 

TorqueMaster®

 

 

Spring Tube and

 

right hand end of the TorqueMaster®

 

 

 

Bearing profiles

 

spring tube. As the right end of the

 

aligned

 

TorqueMaster® spring tube enters the

 

 

 

internal (black) sleeve, rotate the

 

 

 

opener back and forth slightly to help

 

 

 

aid alignment.

 

 

 

Continue sliding the opener onto the

 

 

 

TorqueMaster® spring tube. Align the

 

 

 

right hand bearing with the

 

 

 

TorqueMaster® spring tube and slide

 

 

 

the opener completely onto the

 

 

 

TorqueMaster® spring tube until the

 

 

 

TorqueMaster® spring tube exits the

 

 

 

opener right hand bearing.

 

 

 

NOTE: Do not force the opener onto the

 

 

 

TorqueMaster® spring tube if

 

 

 

misalignment occurs.

 

 

 

Continue sliding the opener to the

 

 

 

center of the TorqueMaster® spring

 

 

 

tube.

 

Plug-in Motor

 

 

 

Power Cord

 

Plug the motor power cord into the

 

 

 

opener.

 

 

20

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer.

To find your Wayne-Dalton dealer; refer to your local yellow pages / business listings or go to Find a dealer area online at www.wayne-dalton.com

Image 20
Contents 5120 Table of Contents Package Contents Door Section Identification Tools Required Torsion Spring Removal For Standard LiftFailure to use approved Winding bars can cause Spring energy to be releasedUsing an electric drill High Counter cover when countingBracket will always have a drive gear Head will be pluggedTorqueMaster Spring RemovalExtension Spring Removal Removing the Old DoorPreparing the Opening Angle to Vertical Track InstallationAttaching Quick Install Flag Installing Q.I. Jamb Brackets Horizontal AngleDrums Bottom SectionVertical Track Stacking SectionsTop Brackets BarBar Asymmetrical Operator BracketTop Section Tools Needed To install horizontal track, place To the slot in the flagangle usingPortion of horizontal track down to Remove the nail that was temporarilyTorqueMaster Spring Tube Center Bracket BushingIdrive Installation Plug the motor power cord into OpenerGarage looking out Right hand end of the TorqueMasterCable Drum Installation Drive Gear Installation End BracketsCounter Installation Securing Center Bracket AssemblyPositioning Support Bracket Handle Bracket Attaching Disconnect CablesMounting Disconnect Attaching Disconnect Handle Cable Adjustments Securing DoorFailure to place vice clamps Onto vertical Track canSetting Spring Tension Winding Bolt RotationDrum Wrap Installation Rear SupportAdjustments to the springs Installation InstructionsParallel with door Or door stop too tightly against faceSide Lock Sold Separately Step Plate Sold Seperately Pull RopeDetermine the Wayne-Dalton Track radius being usedAppropriate 1/2 1 room permitting above of the high Trolley to operator bracketTrolley Installation for Low Headroom Trolley Operator Opens if Photoelectric EYE SystemOperator Rail Suitable mountingPainting CleaningCleaning Your Garage Door Maintenance PaintingLimited Warranty Models 5120