Wayne-Dalton 5120, 5140 Trolley Operator, Opens if Photoelectric EYE System, Operator Rail

Page 35

�

 

Trolley Operator

 

 

 

 

 

 

 

 

 

 

Tools Needed:

 

WARNING

OPERATOR MUST BE TESTED AT TIME

OF INSTALLATION AND MONTHLY

THEREAFTER TO ENSURE THAT DOOR

REVERSES ON CONTACT WITH 2 X 4

BOARD LAID FLAT UNDER THE DOOR.

FAILURE TO ADJUST OPERATOR,

IF NECESSARY, CAN RESULT IN

SEVERE OR FATAL INJURY. IF YOUR

OPERATOR IS EQUIPPED WITH A

PHOTOELECTRIC EYE SYSTEM, THEN

THIS MUST BE TESTED AT THE SAME

TIME TO ENSURE THAT DOOR DOES

NOT CLOSE AND A CLOSING DOOR

OPENS IF PHOTOELECTRIC EYE SYSTEM

IS OBSTRUCTED. FAILURE TO MAKE

ADJUSTMENTS, IF NECESSARY, CAN

RESULT IN SEVERE OR FATAL INJURY.

1.Install operator rail 1/2” to 1-1/2” (13 - 38 mm) above high arc of top section of the door.

2.Mount operator to ceiling so that 1” to 1-1/2” (25 - 38 mm) clearance is maintained between trolley rail and top section when door is fully open (trolley rail will slope down towards rear).

3.Attach door arm to operator bracket installed in Step 12.

4.Attach operator to a suitable mounting surface (2” x 6”) lumber minimum.

5.Attach operator to ceiling using perforated angle.

IMPORTANT: Angles must be securely attached to sound framing member(s).

OPERATOR RAIL

Suitable mounting

surface (2” x 6”) lumber minimum

header

door arm to

operator

bracket

perforated

OPERATORangle rail

OPERATOR

FRAMING MEMBERS

PERFORATED ANGLE

OPTIONAL INSTALLATION

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer.

35

To find your Wayne-Dalton dealer; refer to your local yellow pages / business listings or go to Find a dealer area online at www.wayne-dalton.com

Page 34 Page 36
Image 35
Page 34 Page 36
Contents 5120 Table of Contents Package Contents Door Section Identification Tools Required Winding bars can cause Spring energy to be released Torsion Spring RemovalFor Standard Lift Failure to use approvedHead will be plugged Using an electric drill HighCounter cover when counting Bracket will always have a drive gearRemoval TorqueMaster SpringRemoving the Old Door Extension Spring RemovalPreparing the Opening Angle to Vertical Track InstallationAttaching Quick Install Flag Horizontal Angle Installing Q.I. Jamb BracketsBottom Section DrumsStacking Sections Vertical TrackBar Top BracketsOperator Bracket Bar AsymmetricalTop Section Remove the nail that was temporarily Tools Needed To install horizontal track, placeTo the slot in the flagangle using Portion of horizontal track down toCenter Bracket Bushing TorqueMaster Spring TubeRight hand end of the TorqueMaster Idrive InstallationPlug the motor power cord into Opener Garage looking outCable Drum Installation End Brackets Drive Gear InstallationSecuring Center Bracket Assembly Counter InstallationPositioning Support Bracket Handle Bracket Attaching Disconnect CablesMounting Disconnect Attaching Disconnect Handle Onto vertical Track can Cable AdjustmentsSecuring Door Failure to place vice clampsWinding Bolt Rotation Setting Spring TensionRear Support Drum Wrap InstallationOr door stop too tightly against face Adjustments to the springsInstallation Instructions Parallel with doorSide Lock Sold Separately Pull Rope Step Plate Sold SeperatelyTrolley to operator bracket Determine the Wayne-DaltonTrack radius being used Appropriate 1/2 1 room permitting above of the highTrolley Installation for Low Headroom Suitable mounting Trolley OperatorOpens if Photoelectric EYE System Operator RailPainting CleaningCleaning Your Garage Door Painting MaintenanceLimited Warranty Models 5120
Top Page Image Contents