Wayne-Dalton 5120, 5140 Installation, Attaching Quick Install Flag, Angle to Vertical Track

Page 11

Installation

IMPORTANT: Read instructions titled “p4” “Removing the old door” on page 9 and “p5” “PREPARING THE OPENING” on page 10 before attempting door installation.

IMPORTANT: Stainless steel or PT2000 coated lag screws MUST be used when installing center bearing brackets, end brackets, jamb brackets, operator mounting/support brackets and disconnect brackets on treated lumber (preservative-treated). Stainless steel lag screws are NOT necessary when installing products on un-treated lumber.

NOTE: It is recommended that 5/16” x 1-5/8” lag screws be pilot drilled using a 3/16” drill bit, and 1/4” x 2” lag screws and 1/4” x 1-1/2” lag screws be pilot drilled using a 1/8” drill bit, prior to fastening.

INSTALLATION

1

Attaching Quick Install Flag

Angle to Vertical Track

Tools Needed:

NOTE: If you have riveted track, skip this

None

step.

 

 

Place the lower quick install tab of the

 

flagangle in the quick install feature of

 

the vertical track. Give the flagangle 1/4

 

turn to lock in place. Repeat for other

 

side.

QUICK INSTALL TAB UNLOCKED

QUICK INSTALL TAB LOCKED

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FLAGANGLE

FLAGANGLE

VERTICAL

VERTICAL

TRACK

TRACK

left hand track and flagangle

right hand track and flagangle

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer.

11

To find your Wayne-Dalton dealer; refer to your local yellow pages / business listings or go to Find a dealer area online at www.wayne-dalton.com

Page 10 Page 12
Image 11
Page 10 Page 12
Contents 5120 Table of Contents Package Contents Door Section Identification Tools Required Winding bars can cause Spring energy to be released Torsion Spring RemovalFor Standard Lift Failure to use approvedHead will be plugged Using an electric drill HighCounter cover when counting Bracket will always have a drive gearRemoval TorqueMaster SpringRemoving the Old Door Extension Spring RemovalPreparing the Opening Angle to Vertical Track InstallationAttaching Quick Install Flag Horizontal Angle Installing Q.I. Jamb BracketsBottom Section DrumsStacking Sections Vertical TrackBar Top BracketsOperator Bracket Bar AsymmetricalTop Section Remove the nail that was temporarily Tools Needed To install horizontal track, placeTo the slot in the flagangle using Portion of horizontal track down toCenter Bracket Bushing TorqueMaster Spring TubeRight hand end of the TorqueMaster Idrive InstallationPlug the motor power cord into Opener Garage looking outCable Drum Installation End Brackets Drive Gear InstallationSecuring Center Bracket Assembly Counter InstallationPositioning Support Bracket Handle Bracket Attaching Disconnect CablesMounting Disconnect Attaching Disconnect Handle Onto vertical Track can Cable AdjustmentsSecuring Door Failure to place vice clampsWinding Bolt Rotation Setting Spring TensionRear Support Drum Wrap InstallationOr door stop too tightly against face Adjustments to the springsInstallation Instructions Parallel with doorSide Lock Sold Separately Pull Rope Step Plate Sold SeperatelyTrolley to operator bracket Determine the Wayne-DaltonTrack radius being used Appropriate 1/2 1 room permitting above of the highTrolley Installation for Low Headroom Suitable mounting Trolley OperatorOpens if Photoelectric EYE System Operator RailPainting CleaningCleaning Your Garage Door Painting MaintenanceLimited Warranty Models 5120
Top Page Image Contents