Wayne-Dalton 341458 installation instructions Installing Fully Adjustable Jamb, Brackets

Page 13

 

 

4

Installing Fully Adjustable Jamb

 

Brackets

 

 

Tools Needed:

NOTE: If you have quick install jamb

 

brackets, skip this step and complete

None

Step 5.

 

The bottom jamb bracket is always the

 

shortest bracket included with your

 

door. If three jamb brackets are included

 

with you door, the second bracket up

 

is the middle bracket in height. The

 

top jamb bracket is the tallest bracket

 

included.

To attach the bottom jamb bracket, locate the lower hole/slot pattern of the vertical track. Align the slot in the jamb bracket with the lower hole of the hole/slot pattern in the vertical track. Secure jamb bracket, using

(1)1/4”-20 x 9/16” track bolt and 1/4”-20 flange hex nut.

Place the center jamb bracket over the hole/slot pattern that is centered between the bottom jamb bracket and flagangle. Align the slot in the jamb bracket with the lower hole of the hole/ slot pattern. Loosely fasten the bracket onto the track with (1) 1/4”-20 x 9/16” track bolt and 1/4-20 flange hex nut.

Repeat if a third jamb bracket is provided, equally spacing the distance between the two center jamb brackets and the bottom jamb bracket and flagangle.

NOTE: While the bottom jamb bracket is the shortest in length that is included with your door. It does not necessarily mean it is the “short” (ST-0) jamb bracket.

NOTE: After completing this step, continue with Step 6.

Fully adjustable jamb brackets

ST-0 ST-1

Hole / slot

Jamb pattern bracket

1/4”- 20 x 9/16”

Track bolt

1/4” - 20

flange hexVertical track nut

Jamb bracket

Vertical

track

3rd Set

2nd Set

1st Set

INSTALLATION

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local 13 yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Important Notice DoorsTable of Contents Package Contents Door Section Identification Tools Required For Standard Lift Torsion Spring RemovalFailure to use approved Winding bars can cause Spring energy to be releasedUnwind Springs Removal TorqueMaster SpringBracket and Drive Gear Removing the Old Door Extension Spring RemovalPreparing the Opening Attaching Quick Install Flag Angle to Vertical Track InstallationTools Needed None FlagangleHorizontal Angle Installed as shownTools Needed Place tabs of horizontal angleBrackets Installing Fully Adjustable JambDrums Installing Q.I. Jamb BracketsVertical Track Bottom SectionTop Brackets Stacking SectionsProperly Operator BracketTop Section Attaching Horizontal Track To Quick Install FlagangleDo not Raise Door Until InjurySevere or Fatal Injury Center Bracket Bushing TorqueMaster Spring TubeCable Drums Drum WrapsGarage Looking OUT End Brackets Tools Needed Power Drill Socket Driver Wrench16 18 x 3/4 Securing Center Bracket AssemblyRight End Bracket 16 x 1-5/8Securing Door For Spring Winding Cable AdjustmentRecommended Spring Turns Winding SpringsTools Needed To install drum wraps, position the left Drum Wrap InstallationHand drum wrap over the left hand Raising door further can Rear SupportResult in door falling Otherwise door could fallFull Tension of the Spring Spring Turn ChartCompany Reset the System TorqueMaster Plus Reset InstructionsResetting the ANTI-DROP Device While the Door is MovingBalancing Door Steps to reset the systemPawl TorqueMaster Plus Reset Side Lock Tools Needed Power Drill Drill BitPull Rope Pull Rope Bottom BracketFailure to Make Adjustments Or REPAIRS, if NECESSARY, can Immediate adjustments or repairsInstall operator rail 1/2 to Trolley OperatorGlass Cleaning Instructions Cleaning Your Steel And Fiberglass Garage DoorAcrylic Cleaning Instructions Important do not USE a Pressure Washer on Garage DoorFiberglass Refinishing And Or Finishing Steel Preparation For PaintingLifetime Limited Warranty Model Thank you for your purchase
Top Page Image Contents