Wayne-Dalton 341458 Drum Wrap Installation, Tools Needed To install drum wraps, position the left

Page 27

Tools Needed:

Winding Springs Continued...

To wind the spring, rotate the winding shaft clockwise, while watching the mark on the

Back of torquemaster® plus end bracket warning tag(s)

winding shaft. Rotate the winding shaft to the required number of turns for your door. Then return to the right hand side and wind the right hand spring to the required number of turns. Place pawl knob in lower position on both sides.

IMPORTANT: Mark number of spring turns on TorqueMaster® Plus end bracket warning tag(s).

NOTE: Since total turns to balance door can deviate from spring turn chart values by ± 1/2 turn, adjustments to the recommended number of turns may be required after rear hangers assembly is completed.

IMPORTANT! Hold the door down to prevent it from rising unexpectedly in the event the spring was overwound and cautiously remove vice clamps from vertical tracks. IMPORTANT! Adjustments to the recommended number of turns may be required. If door raises off the floor under spring tension alone, then reduce spring tension until door rest on the floor. If the door is hard to raise or drifts down on its own, then add spring tension.

Spring Turns

Door Height

Spring Turns

(6’ - 0”)

14

(6’ - 3”)

14 - 1/2

(6’ - 5”)

15

(6’ - 6”)

15

(6’ - 8”)

15 - 1/2

(6’ - 9”)

15 - 1/2

(7’ - 0”)

16

(7’ - 3”)

16 - 1/2

(7’ - 6”)

17

(7’ - 9”)

17 - 1/2

(8’ - 0”)

18

Number of Installed Spring Turns

Location for

marking number

of installed spring turns

INSTALLATION

25

Drum Wrap Installation

Drum wrap

 

(left hand)

 

 

 

 

Tools Needed:

To install drum wraps, position the left

Drum

 

None

hand drum wrap over the left hand

 

(left hand)

 

drum, align with counterbalance cable;

 

 

 

 

 

slide groove in drum wrap towards the

 

 

 

left until tabs snap over drum in

 

 

 

between drum and ratchet gear. Repeat

 

 

 

for right hand side.

 

 

 

IMPORTANT: Right and Left hand

 

 

 

are always determined from inside

 

 

 

the Garage looking out.

 

 

 

 

Counterbalance

 

 

 

cable

 

 

 

Tabs

 

 

 

Groove

 

 

 

in drum

 

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local

27

 

yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com

 

Image 27
Contents Important Notice DoorsTable of Contents Package Contents Door Section Identification Tools Required Winding bars can cause Spring energy to be released Torsion Spring RemovalFor Standard Lift Failure to use approvedUnwind Springs TorqueMaster Spring RemovalBracket and Drive Gear Removing the Old Door Extension Spring RemovalPreparing the Opening Flagangle InstallationAttaching Quick Install Flag Angle to Vertical Track Tools Needed NonePlace tabs of horizontal angle Installed as shownHorizontal Angle Tools NeededBrackets Installing Fully Adjustable JambDrums Installing Q.I. Jamb BracketsVertical Track Bottom SectionTop Brackets Stacking SectionsProperly Operator BracketTop Section Injury To Quick Install FlagangleAttaching Horizontal Track Do not Raise Door UntilSevere or Fatal Injury Center Bracket Bushing TorqueMaster Spring TubeDrum Wraps Cable DrumsGarage Looking OUT End Brackets Tools Needed Power Drill Socket Driver Wrench16 x 1-5/8 Securing Center Bracket Assembly16 18 x 3/4 Right End BracketSecuring Door For Spring Winding Cable AdjustmentRecommended Spring Turns Winding SpringsDrum Wrap Installation Tools Needed To install drum wraps, position the leftHand drum wrap over the left hand Otherwise door could fall Rear SupportRaising door further can Result in door fallingFull Tension of the Spring Spring Turn ChartWhile the Door is Moving TorqueMaster Plus Reset InstructionsCompany Reset the System Resetting the ANTI-DROP DeviceSteps to reset the system Balancing DoorPawl TorqueMaster Plus Reset Pull Rope Bottom Bracket Tools Needed Power Drill Drill BitSide Lock Pull RopeTrolley Operator Immediate adjustments or repairsFailure to Make Adjustments Or REPAIRS, if NECESSARY, can Install operator rail 1/2 toImportant do not USE a Pressure Washer on Garage Door Cleaning Your Steel And Fiberglass Garage DoorGlass Cleaning Instructions Acrylic Cleaning InstructionsFiberglass Refinishing And Or Finishing Steel Preparation For PaintingLifetime Limited Warranty Model Thank you for your purchase