Wayne-Dalton 341458 installation instructions Tools Required

Page 5

Tools Required

Power Drill

Ratchet Wrench

Pliers/Wire Cutters

Tape Measure

1/8”, 3/16” Drill Bits

 

 

 

 

INSTALLATIONPRE-

Phillips Head Screwdriver

Flat Tip Screwdriver

Pencil

Needle Nose Pliers

Gloves

7/16”, 1/2”, 9/16”

7/16” Socket Driver

3/8”, 7/16”, 1/2”, 9/16”

Safety Glasses

 

Sockets

 

Wrenches

 

 

 

 

 

 

Step Ladder

Hammer

vice grips

Vice clamps

(2) Saw Horses

 

Removing An Old Door

WARNING

If your counterbalance system is other than those mentioned IN SECTIONS P1, P2 AND P3, do not attempt to work on it, but have a qualified door agency perform the work. Otherwise, severe or fatal injury could result.

WARNING

Disconnect and remove any electric opener prior to removal of counterbalance systems to prevent unintended door operation. Otherwise, severe or fatal injury could result.

WARNING

Counterbalance spring tension must be relieved before removing any hardware. A powerful spring releasing it’s energy suddenly can cause severe or fatal injury.

WARNING

If you have back problems do not attempt this, or severe injury could result

WARNING

Removing an existing door can be dangerous. Follow instructions on pages 6-10 “removing an old door/preparing the opening” carefully, otherwise, severe or fatal injury could result.

If you have an existing door, follow the instructions to identify which counterbalance removal is necessary. The process of removing an existing door begins by identifying it’s counterbalance system. If you are not removing an existing door, proceed to Preparing The Opening on page 10. Generally, you will find three (3) types of counterbalance systems: Torsion spring counterbalance systems, Wayne- Dalton® exclusive TorqueMaster® and extension Spring counterbalance systems.

For more technical information regarding the opening preparation, installation and use of your garage door and opener, you can go to www.dasma.com and click on Publications and then Technical Data Sheets Number 156, 161 and 164.

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local 5 yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Important Notice DoorsTable of Contents Package Contents Door Section Identification Tools Required For Standard Lift Torsion Spring RemovalFailure to use approved Winding bars can cause Spring energy to be releasedUnwind Springs Bracket and Drive Gear TorqueMaster SpringRemoval Removing the Old Door Extension Spring RemovalPreparing the Opening Attaching Quick Install Flag Angle to Vertical Track InstallationTools Needed None FlagangleHorizontal Angle Installed as shownTools Needed Place tabs of horizontal angleBrackets Installing Fully Adjustable JambDrums Installing Q.I. Jamb BracketsVertical Track Bottom SectionTop Brackets Stacking SectionsProperly Operator BracketTop Section Attaching Horizontal Track To Quick Install FlagangleDo not Raise Door Until InjurySevere or Fatal Injury Center Bracket Bushing TorqueMaster Spring TubeGarage Looking OUT Drum WrapsCable Drums End Brackets Tools Needed Power Drill Socket Driver Wrench16 18 x 3/4 Securing Center Bracket AssemblyRight End Bracket 16 x 1-5/8Securing Door For Spring Winding Cable AdjustmentRecommended Spring Turns Winding SpringsHand drum wrap over the left hand Drum Wrap InstallationTools Needed To install drum wraps, position the left Raising door further can Rear SupportResult in door falling Otherwise door could fallFull Tension of the Spring Spring Turn ChartCompany Reset the System TorqueMaster Plus Reset InstructionsResetting the ANTI-DROP Device While the Door is MovingPawl Steps to reset the systemBalancing Door TorqueMaster Plus Reset Side Lock Tools Needed Power Drill Drill BitPull Rope Pull Rope Bottom BracketFailure to Make Adjustments Or REPAIRS, if NECESSARY, can Immediate adjustments or repairsInstall operator rail 1/2 to Trolley OperatorGlass Cleaning Instructions Cleaning Your Steel And Fiberglass Garage DoorAcrylic Cleaning Instructions Important do not USE a Pressure Washer on Garage DoorFiberglass Refinishing And Or Finishing Steel Preparation For PaintingLifetime Limited Warranty Model Thank you for your purchase
Top Page Image Contents