Wayne-Dalton 341458 Securing Center Bracket Assembly, 16 18 x 3/4, Right End Bracket, 16 x 1-5/8

Tools Needed:

End Brackets Continued...

First secure end bracket to the flagangle using (1) 5/16” - 18 x 3/4” carriage bolt and (1) 5/16” - 18 hex nut. Now, secure end bracket to the jamb using (1) 5/16” x 1-5/8” hex head lag screw. Repeat for left hand end bracket.

NOTE: Ensure the 5/16” - 18 x 3/4” carriage bolt is going through the flagangle first, and the 5/16” - 18 hex nut is on the outside of the end bracket.

IMPORTANT: If ratchet gear slips out of end bracket, ensure the teeth on ratchet wheel are pointing upward in a clockwise position when sliding it back inside the end bracket.

Right End

Bracket

Warning Tag

Use

thesel

thislabe.

R WAM

Teeth Pointing

R

achet

To

Brack

EXTRE

etNINGis

side

un

der

fatalavoidTENSIOible se

of

poss

SPRING.

fasteninjury,

DO

ers

NOT vere

Upward

until

from

or

To

rat

rem

ENG

spring(s)chet

ove

and

fosafelywnwo ar

fullybracket

l

unwiund.

low

nd

installationtheread spri

DO

direc

ng(s)

NOT

m

ctiottions

int

D

No

anual ns/

rum

REMO

.

he

Ratscpace bet

VE

owners

Cahetb

Pawl

and

THIS

TA

le Dr

l

Ratchet

DISum

G.

ENG

AGED

SIDE VIEW

um

t

DIS

A

Ratchet

ENG

GED U

NDERNEATH VIEW

Rat

Notsp

chetPawl

Cable Drum

Wheel

Ra chace bet

Space

UPP

et

Pawlween

between

ER

Cable

Drumand

POSITION

non-iand CableRatchet

ndicates

Drum Pawl

LOWER

POSITION

engagement

Right End

Bracket

5/16” x 1-5/8”

Use t

this labheseel.

RacWAR

het B

To

EXTR racketNING

EME

is u

nder

side of

fatalavoidinj

TENS

pos

IONSPRING.

fasten ury, sible

severe

e

ers

DO

Hex Head Lag

untilspfrom

NOT

or

To

ring(sratchet) remov

and

safelywnwoundare. fbracullyket

5/16” - 18 x 3/4”

inst

follow read

s

pring(s)

allationithe direc

DO

nstruc

tions t

NOT REmanualtions.

in

he

MOVE

/owners

THIS TAG.

CARRIAGE Bolt

AND HEX NUT

21	Securing Center Bracket
	Assembly	CENTER
		BRACKET
Tools Needed:	NOTE: If you are installing the idrive®	bushing
Power Drill	opener with your garage door, skip this	ASSEMBLY
	step.
3/16” Drill Bit
7/16” Socket	NOTE: If you are not installing the
Driver	idrive® opener on your garage door, you
	must install the center bracket bushing
	assembly. Follow these instructions for
	non-idrive®operated garage doors.

To locate the center bracket, mark the header halfway between the flagangles and level the TorqueMaster® spring tube. Drill 3/16” pilot holes into header for the lag screws. Fasten the metal bracket to the header using (2) 5/16” x 1-5/8” lag screws.

(2) 5/16” x 1-5/8” hex head lag screws

24Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local

yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com