Wayne-Dalton 341458 installation instructions Securing Door For Spring Winding, Cable Adjustment

Page 25

22

Tools Needed:

Vice Clamps

Securing Door

for Spring Winding

Place vice clamps onto both vertical tracks just above the third roller. This is to prevent the garage door from raising while winding counterbalance springs.

WARNING

Failure to place vice clamps onto vertical Track can allow door to raise and cause severe or fatal injury.

NOTE: Four section, 8’0” high

door is shown.

Place vice

clamps above

3rd Roller

Vice clamps

attached to Track track

INSTALLATION

23

Tools Needed:

Pliers/Wire

Cutters

Flat Tip

Screwdriver

Cable Adjustment

Starting on the right side, adjust the cable drum assembly by rotating the drum until the set screw faces directly away from the header. Loosen the set screw no more than 1/2 turn.

Pull on the end of the cable to remove all cable slack. Check to ensure the cable is aligned and seated in the first groove of the cable drum. Snug the set screw, and then tighten an additional 1-1/2 turns.

First Groove

Set Screw

Use these

WAR

 

this label

Rachet Brac

 

 

 

 

EXTREME

 

 

TENS

 

 

To avoid possi

 

 

fatal injury, D

Counterbalance Cable

Cut off excess cable.

in First Groove

Cam Peak Strait Up

 

IMPORTANT: Ensure the cable is aligned and seated in the First groove of the cable drum prior to winding springs.

NOTE: Illustrations show the right

Pliers

Set Screw

 

TorqueMaster® Plus drum, left

Use

Counterbalance

this

TorqueMaster® Plus drum is

 

 

 

Cable

 

symmetrically opposite.

 

 

 

 

 

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local

25

yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com

 

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Important Notice DoorsTable of Contents Package Contents Door Section Identification Tools Required For Standard Lift Torsion Spring RemovalFailure to use approved Winding bars can cause Spring energy to be releasedUnwind Springs Removal TorqueMaster SpringBracket and Drive Gear Removing the Old Door Extension Spring RemovalPreparing the Opening Attaching Quick Install Flag Angle to Vertical Track InstallationTools Needed None FlagangleHorizontal Angle Installed as shownTools Needed Place tabs of horizontal angleBrackets Installing Fully Adjustable JambDrums Installing Q.I. Jamb BracketsVertical Track Bottom SectionTop Brackets Stacking SectionsProperly Operator BracketTop Section Attaching Horizontal Track To Quick Install FlagangleDo not Raise Door Until InjurySevere or Fatal Injury Center Bracket Bushing TorqueMaster Spring TubeCable Drums Drum WrapsGarage Looking OUT End Brackets Tools Needed Power Drill Socket Driver Wrench16 18 x 3/4 Securing Center Bracket AssemblyRight End Bracket 16 x 1-5/8Securing Door For Spring Winding Cable AdjustmentRecommended Spring Turns Winding SpringsTools Needed To install drum wraps, position the left Drum Wrap InstallationHand drum wrap over the left hand Raising door further can Rear SupportResult in door falling Otherwise door could fallFull Tension of the Spring Spring Turn ChartCompany Reset the System TorqueMaster Plus Reset InstructionsResetting the ANTI-DROP Device While the Door is MovingBalancing Door Steps to reset the systemPawl TorqueMaster Plus Reset Side Lock Tools Needed Power Drill Drill BitPull Rope Pull Rope Bottom BracketFailure to Make Adjustments Or REPAIRS, if NECESSARY, can Immediate adjustments or repairsInstall operator rail 1/2 to Trolley OperatorGlass Cleaning Instructions Cleaning Your Steel And Fiberglass Garage DoorAcrylic Cleaning Instructions Important do not USE a Pressure Washer on Garage DoorFiberglass Refinishing And Or Finishing Steel Preparation For PaintingLifetime Limited Warranty Model Thank you for your purchase
Top Page Image Contents