Wayne-Dalton 341458 installation instructions TorqueMaster Spring Tube, Center Bracket Bushing

Page 21

		TorqueMaster® Spring Tube

	Tools Needed:	TorqueMaster® springs come lubricated
	None	and pre-assembled inside the
	None	TorqueMaster® spring tube. To install, lay
		TorqueMaster® spring tube. To install, lay
		the TorqueMaster® spring tube on the
		floor (inside garage) in front of the door
		with the labeled end to the left.

			TorqueMaster®	INSTALLATION
			Spring Tube
		LABELED END

17	Center Bracket Bushing			CENTER
				BRACKET
				ASSEMBLY

Tools Needed:	NOTE: If you are installing the idrive®
None	opener with your garage door, skip this
None	step and go to your idrive® Installation
	step and go to your idrive® Installation
	Instruction/Owner’s Manual. After
	completing Steps 1 thru 10 in your
	idrive® Installation Instruction/Owner’s	TorqueMaster®
	Manual, continue with Step 22 of the	Spring Tube
	door Installation Instruction/Owner’s
	Manual.
	NOTE: If you are not installing an idrive®
	opener with your garage door, you
	must install the center bracket bushing	TorqueMaster®
	assembly. Continue to follow these	Spring Tube
	assembly. Continue to follow these
	instructions for non-idrive®operated
	garage doors.
	Being cam shaped the center bracket
	bushing only fits one way.
	Slide the center bracket assembly
	towards the center of the TorqueMaster®	CENTER
	spring tube, from the right side as	CENTER
	spring tube, from the right side as	BRACKET
	shown.	BUSHING

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local 21 yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com

Image 21

Contents Important Notice DoorsTable of Contents Package Contents Door Section Identification Tools Required For Standard Lift Torsion Spring RemovalFailure to use approved Winding bars can cause Spring energy to be releasedUnwind Springs TorqueMaster Spring RemovalBracket and Drive Gear Removing the Old Door Extension Spring RemovalPreparing the Opening Attaching Quick Install Flag Angle to Vertical Track InstallationTools Needed None FlagangleHorizontal Angle Installed as shownTools Needed Place tabs of horizontal angleBrackets Installing Fully Adjustable JambDrums Installing Q.I. Jamb BracketsVertical Track Bottom SectionTop Brackets Stacking SectionsProperly Operator BracketTop Section Attaching Horizontal Track To Quick Install FlagangleDo not Raise Door Until InjurySevere or Fatal Injury Center Bracket Bushing TorqueMaster Spring TubeDrum Wraps Cable DrumsGarage Looking OUT End Brackets Tools Needed Power Drill Socket Driver Wrench16 18 x 3/4 Securing Center Bracket AssemblyRight End Bracket 16 x 1-5/8Securing Door For Spring Winding Cable AdjustmentRecommended Spring Turns Winding SpringsDrum Wrap Installation Tools Needed To install drum wraps, position the leftHand drum wrap over the left hand Raising door further can Rear SupportResult in door falling Otherwise door could fallFull Tension of the Spring Spring Turn ChartCompany Reset the System TorqueMaster Plus Reset InstructionsResetting the ANTI-DROP Device While the Door is MovingSteps to reset the system Balancing DoorPawl TorqueMaster Plus Reset Side Lock Tools Needed Power Drill Drill BitPull Rope Pull Rope Bottom BracketFailure to Make Adjustments Or REPAIRS, if NECESSARY, can Immediate adjustments or repairsInstall operator rail 1/2 to Trolley OperatorGlass Cleaning Instructions Cleaning Your Steel And Fiberglass Garage DoorAcrylic Cleaning Instructions Important do not USE a Pressure Washer on Garage DoorFiberglass Refinishing And Or Finishing Steel Preparation For PaintingLifetime Limited Warranty Model Thank you for your purchase