Wayne-Dalton 341458 installation instructions Trolley Operator, Immediate adjustments or repairs

Page 34

 

Trolley Operator

Tools Needed:

Align hole in the appropriate arm with

holes in operator bracket tabs. Insert

 

None

5/16” x 1-1/4” clevis pin, making sure

hole in clevis pin is outside of second

 

 

tab of operator bracket. Insert hairpin

 

cotter into clevis pin hole and spread

 

hairpin cotter to ensure it will secure

 

assembly. Operator must be tested at

 

time of installation and monthly there

 

after to ensure that door reverses on

 

contact with 2” x 4” board laid flat under

 

the door. Failure to pass this test requires

 

immediate adjustments or repairs.

WARNING

FAILURE TO MAKE ADJUSTMENTS

OR REPAIRS, IF NECESSARY, CAN

RESULT IN SEVERE OR FATAL

INJURY.

If your operator is equipped with a photoelectric eye system, then this must be tested at the same time to ensure that door does not close and a closing door opens, if photoelectric eye system is obstructed. Failure to pass this test requires immediate adjustments or repairs.

WARNING

FAILURE TO MAKE ADJUSTMENTS

OR REPAIRS, IF NECESSARY, CAN

RESULT IN SEVERE OR FATAL

INJURY.

1.Install operator rail 1/2” to 1”

(13 mm - 38 mm) above high arc of top section of the door.

2.Mount operator to ceiling so that 1” to 1-1/2” (25 - 38 mm) clearance is maintained between trolley rail and top section when door is fully open (trolley rail will slope down towards rear).

3.Attach door arm to operator bracket installed in Step 9.

4.Attach operator rail to suitable mounting surface, 2” x 6” lumber minimum.

5.Attach operator to ceiling using perforated angle.

IMPORTANT! Perforated Angle must be securely attached to sound framing member(s).

Operator

 

 

 

Bracket

 

 

Hairpin

Operator

tabs

 

Bracket

Cotter

 

5/16” x 1-1/4”

Door

Clevis pin

Arm

 

Hairpin Cotter

SUITABLE

(Outside of operator

MOUNTING

bracket tab)

SURFACE (2 X 6)

LUMBER MIN.

 

HEADER

Operator

bracket tabs

Door arm

OPERATOR

RAIL

 

DOOR ARM TO OPERATOR

BRACKET

Top view

Perforated

OPERATOR angle rail

OPERATOR

FRAMING

MEMBERS

PERFORATED ANGLE

34Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local

yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Doors Important NoticeTable of Contents Package Contents Door Section Identification Tools Required Failure to use approved Torsion Spring RemovalFor Standard Lift Winding bars can cause Spring energy to be releasedUnwind Springs Removal TorqueMaster SpringBracket and Drive Gear Extension Spring Removal Removing the Old DoorPreparing the Opening Tools Needed None InstallationAttaching Quick Install Flag Angle to Vertical Track FlagangleTools Needed Installed as shownHorizontal Angle Place tabs of horizontal angleInstalling Fully Adjustable Jamb BracketsInstalling Q.I. Jamb Brackets DrumsBottom Section Vertical TrackStacking Sections Top BracketsOperator Bracket ProperlyTop Section Do not Raise Door Until To Quick Install FlagangleAttaching Horizontal Track InjurySevere or Fatal Injury TorqueMaster Spring Tube Center Bracket BushingCable Drums Drum WrapsGarage Looking OUT Tools Needed Power Drill Socket Driver Wrench End BracketsRight End Bracket Securing Center Bracket Assembly16 18 x 3/4 16 x 1-5/8Cable Adjustment Securing Door For Spring WindingWinding Springs Recommended Spring TurnsTools Needed To install drum wraps, position the left Drum Wrap InstallationHand drum wrap over the left hand Result in door falling Rear SupportRaising door further can Otherwise door could fallSpring Turn Chart Full Tension of the SpringResetting the ANTI-DROP Device TorqueMaster Plus Reset InstructionsCompany Reset the System While the Door is MovingBalancing Door Steps to reset the systemPawl TorqueMaster Plus Reset Pull Rope Tools Needed Power Drill Drill BitSide Lock Pull Rope Bottom BracketInstall operator rail 1/2 to Immediate adjustments or repairsFailure to Make Adjustments Or REPAIRS, if NECESSARY, can Trolley OperatorAcrylic Cleaning Instructions Cleaning Your Steel And Fiberglass Garage DoorGlass Cleaning Instructions Important do not USE a Pressure Washer on Garage DoorSteel Preparation For Painting Fiberglass Refinishing And Or FinishingLifetime Limited Warranty Model Thank you for your purchase
Top Page Image Contents