Wayne-Dalton Wayne Dalton Dealer & TorqueMaster Spring Installation Instructions
Page 22

18

Tools Needed:

None

Drum Wraps

NOTE: Drum wraps must be installed prior to installing the TorqueMaster® plus end bracket. Drum wrap installation after the end bracket is installed, is not possible without un-installing the end bracket and it’s components.

IMPORTANT: RIGHT AND LEFT HAND IS ALWAYS DETERMINED FROM INSIDE THE GARAGE LOOKING OUT.

Drum wraps are identified as right and left. Slide the left hand drum wrap over the left side of the TorqueMaster® spring tube assembly with the tabs facing left. Continue sliding the left hand drum wrap towards the center of the TorqueMaster® spring tube assembly. Slide the right hand drum wrap over the right side of the TorqueMaster® spring tube assembly with the tabs facing right. Continue sliding the right hand drum wrap towards the center of the TorqueMaster® spring tube assembly.

Right Hand Drum Wrap

Left Hand Drum Wrap

Left Hand Drum Wrap

TorqueMaster®

Spring Tube Assembly

Tabs

19

Cable Drums

TorqueMaster®

 

 

Spring Tube Assembly

 

 

Tools Needed:

Shake the TorqueMaster® spring tube

Winding

 

assembly gently to extend the winding

Tape Measure

Shaft

shafts out about 5" on each side. For

 

 

 

single spring applications, there will be

 

 

no left hand spring in the TorqueMaster®

 

 

spring tube assembly.

 

 

Lift the TorqueMaster® spring tube

 

 

assembly and rest it on the top of the

 

 

flagangles.

 

 

NOTE: Cable drums are marked right

 

 

and left hand. Cable drums and

Right Drum

 

TorqueMaster® spring tube assembly

 

 

 

are cam shaped to fit together only one

 

 

way.

 

 

IMPORTANT: RIGHT AND LEFT HAND IS

 

 

ALWAYS DETERMINED FROM INSIDE THE

 

 

GARAGE LOOKING OUT.

 

 

To install the cable drum, slide the

TorqueMaster®

 

correct cable drum over the winding

Spring Tube Assembly

 

shaft until the cable drum seats against

 

 

 

the TorqueMaster® spring tube

 

 

assembly.

 

22Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local

yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Doors Important NoticeTable of Contents Package Contents Door Section Identification Tools Required Failure to use approved Torsion Spring RemovalFor Standard Lift Winding bars can cause Spring energy to be releasedUnwind Springs Removal TorqueMaster SpringBracket and Drive Gear Extension Spring Removal Removing the Old DoorPreparing the Opening Tools Needed None InstallationAttaching Quick Install Flag Angle to Vertical Track FlagangleTools Needed Installed as shownHorizontal Angle Place tabs of horizontal angleInstalling Fully Adjustable Jamb BracketsInstalling Q.I. Jamb Brackets DrumsBottom Section Vertical TrackStacking Sections Top BracketsOperator Bracket ProperlyTop Section Do not Raise Door Until To Quick Install FlagangleAttaching Horizontal Track InjurySevere or Fatal Injury TorqueMaster Spring Tube Center Bracket BushingCable Drums Drum WrapsGarage Looking OUT Tools Needed Power Drill Socket Driver Wrench End BracketsRight End Bracket Securing Center Bracket Assembly16 18 x 3/4 16 x 1-5/8Cable Adjustment Securing Door For Spring WindingWinding Springs Recommended Spring TurnsTools Needed To install drum wraps, position the left Drum Wrap InstallationHand drum wrap over the left hand Result in door falling Rear SupportRaising door further can Otherwise door could fallSpring Turn Chart Full Tension of the SpringResetting the ANTI-DROP Device TorqueMaster Plus Reset InstructionsCompany Reset the System While the Door is MovingBalancing Door Steps to reset the systemPawl TorqueMaster Plus Reset Pull Rope Tools Needed Power Drill Drill BitSide Lock Pull Rope Bottom BracketInstall operator rail 1/2 to Immediate adjustments or repairsFailure to Make Adjustments Or REPAIRS, if NECESSARY, can Trolley OperatorAcrylic Cleaning Instructions Cleaning Your Steel And Fiberglass Garage DoorGlass Cleaning Instructions Important do not USE a Pressure Washer on Garage DoorSteel Preparation For Painting Fiberglass Refinishing And Or FinishingLifetime Limited Warranty Model Thank you for your purchase
Top Page Image Contents