Genie PCG, GCG manual Installation, Header and Door Mounting Brackets, Marking final height

Page 11

 

2

INSTALLATION

FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM

 

 

I M P O R TA N T

WARNING :

 

 

 

 

 

To reduce the risk of severe injury or death:

11

1.READ AND FOLLOW ALL SAFETY, INSTALLATION AND OPERATION INSTRUCTIONS. If you have questions or do not understand an instruction, call The Genie Company or an authorized Genie Dealer.

2.Do Not install operator on an improperly balanced door. An improperly balanced door could cause severe injury. Repairs and adjustments to cables, spring assembly, and other hardware must be made by a professionally trained service technician using proper tools and instructions.

3.Remove all ropes and disable all locks connected to the door before installing operator.

4.Install door operator 7 feet or more above floor. Mount emergency release knob 6 feet above floor.

5.Do Not connect the operator to the source of power until instructed to do so.

6.Locate the control button:

Within sight of door.

At minimum height of 5 feet above the highest floor level, so small children cannot reach it.

Away from all moving parts of the door.

7.Install the Entrapment WARNING Label next to the wall button or wall console. Install the emergency release tag on, or next to, the emergency release.

8.The operator must reverse when the door contacts a 1-1/2 inch high object on the floor at the center of the doorway. This is the size of a 2 x 4 board laid flat.

HEADER AND DOOR

MOUNTING BRACKETS:

CAUTION

Header bracket must be fastened to garage framing. Do Not fasten to drywall, particle board, plaster or other such materials.

1. Finding header bracket mounting location.

Close garage door.

 

Use a pencil.

 

a. Mark center of garage door (one-half overall

 

width) with 6 vertical line at top edge of door.

 

b. Continue this line on wall above door for

 

about 12" (Fig. 2-1).

Raise garage door until top edge of door

from here to

floor

FIG. 2-1 Finding highest point of travel (sectional).

reaches its maximum height (Fig. 2-2).

Place door at highest point.

Measure height from top edge of door to floor.

Close door again.

Mark height measurement on wall above door.

 

Make your mark across vertical line

 

made earlier.

 

 

Marking final height.

THE 2 BASIC TYPES OF GARAGE DOOR MECHANISMS ARE:

Sectional doorshave rollers on each side which ride in tracks to guide the door up and down.

One-Piecedoorsswivel on large spring loaded hinges as the door opens and closes.

For sectional add 2-1/2" to height mark just made on wall. This is location for header bracket.

NOTE: If spring or its shaft is in way, measure

2-1/2" above spring or shaft and mark this height as your location for header bracket.

For one-pieceadd 6"- 12 to your height mark

just made on the wall. This is location for

from here to

floor

FIG. 2-2 Finding highest point of travel (1-piece).

top of door

final height

mark

header bracket.

FIG. 2-3 Final height mark.

Image 11
Contents Garage Door Operator PRE-INSTALLATION Check List Typical 1-PIECE Door Installation Typical Sectional Door InstallationSafety Features Table of ContentsOperator Features Parts Identification Not Shown Full Size Recommended ToolsPiece Rail Hardware Exploded View Safety Information Parts ListPower Head Exploded View Operator Assembly Attach emergency release tag Attach rail to power headSlip carriage into carriage slot of rail Slip opposite no knot end through knobAttach limit switch wires Attach limit switchesMarking final height InstallationHeader and Door Mounting Brackets Finding header bracket mounting locationMounting the door bracket Door Bracket12 2. Mounting the header bracket Finding door bracket mounting locationMounting the Operator Attach the arms Connecting the armsSAFE-T-BEAM System Installation Check the following WiringFinding the mounting location Wall Control InstallationInstructions for electrician Connecting to PowerWith Permanent Wiring With Grounded PlugAdjusting Close force Limit Switch / Force AdjustmentAdjusting limit switches Adjusting Open forceContact Reverse Test Programming Remote Controls Single Button RemoteLost or Stolen Remote Light BULB/LENS InstallationMULTI-BUTTON Remote Door balance Maintenance Routine Monthly MaintenanceTroubleshooting Guide Door springs and hardwareDoor operator Operator runsBut door does Not moveTransmitter Compliance Statement Wiring DiagramPlease have part number and credit card ready DistributorGenie Company Garage Door Operator Accessories Order FormLimited Warranty Ayuda Para Temps de combien Pendant Brevets d’autres pour effectuée DemandeMexique au ou Canada au Unis,-Etats aux achetés Genie Produit le acheté initialementConnexion DE Schéma Cableado DE DiagramaRaison sans Mantenimiento de secciónProblème RemonteVerde .L.D Rojo .L.D Problemas DE Solución LA Para GuíaMantenimiento Chariot du Dépannage DE GuideEntretien Verte del Rouge delLente ET Pile DE Changement TélécommandePince LA DE Installation REMOTO, Control DEL InstalaciónInversión DE Contacto DE Prueba Télécommandes DES ProgrammationProgramación DE Remotos Controles ParedFig corredizo Abrir de límiteFuerza LA DE Ajuste / Limitador Interruptor Branchement Eléctrica Alimentación LA ConectarCiego agujero Tornillo VisBorne la à Murale commande la de l’arrière ÀMurales Commandes DES Installation Pared DE Control DEL InstalaciónControl de AjustadasNecesario Sensor del’extension BEAM-T-SAFE Systeme DU InstallationBEAM-T-SAFE Sistema DEL Instalación 1 x 16-#1012-2 .Fig Porte LA DE Bras LES InstallerOperador DEL Montaje Garde EN Mise PrecauciónPorte DE Montage DE ET Linteau DE Supports InstallaciónInstallation Puerta LA DE Montaje DEL Travesaño DEL CartelasRail Riel delRail du Esquina 7,-1 .FigDeuxième Operador DEL Conjunto’OPÉRATEUR DE Assemblage TroisièmeMotorisée Tète Éclatée VUE Control DE Caja LA DE Piezas DE ListaPiezas DE Lista Seguridad DE InformaciónArt Sécurité LA À Relatives InformationsPièces DES Nomenclature Motorisée Tète LA DE Pièces DES NomenclatureÉclatée VUE Rail DU Quincaillerie Éclatée VUE Rail DU QuincaillerieRiel DEL Herraje DEL Aumentada Vista Riel DEL Herraje DEL Aumentada VistaRecomendar Herramientas Recommande OutilsSujetadores Attaches Piezas DE IdentificaciónModelos algunos con incluido Operador DEL Características ÍndiceSeguridad DE Características Modelos algunos con incluida iluminada pared de ConsolaMatières DES Table Sécurité DE Caractéristiques’OPÉRATEUR DE Caractéristiques Monopièce Porte DE Installation De sistema del montaje de lugar el si ver para Verificar Votre sur l’installation pour 2-GER d’urgence déclenchementDe obligé certainement serez Vous .montage de emplacement Lentamente muy bajar o está, donde quedarse debe puerta LaPuertas de

GCG, H, PCG specifications

Genie PCG, H, and GCG represent a series of innovative computing devices designed to meet the diverse needs of modern users. Each model caters to specific requirements, yet they share common technological foundations that enhance performance, user experience, and energy efficiency.

The Genie PCG offers a powerhouse performance with its state-of-the-art processors and an emphasis on portability. It is designed for professionals and students who require a reliable device for multitasking, whether it’s for running demanding applications or standard productivity software. Equipped with a high-resolution display and a backlit keyboard, the PCG delivers an immersive visual experience and usability in low-light conditions. Its lightweight and slim design make it highly portable, making it easy to carry around without compromising performance.

On the other hand, the Genie H is specifically tailored for home users. It focuses on providing a seamless entertainment experience, equipped with integrated graphics and sound technologies that enhance media consumption. Whether you're streaming your favorite shows, playing games, or connecting with friends and family through video calls, the Genie H ensures superior visuals and crystal-clear audio. Its larger screen size complements its use as a central hub for home entertainment, featuring smart connectivity options that allow users to connect various devices effortlessly.

The Genie GCG is the advanced computing solution for gamers and tech enthusiasts. This model stands out with its high-performance graphics card and advanced cooling technology, ensuring optimal gaming performance even under heavy loads. The GCG is designed to handle the latest games, with high refresh rates and low latency delivering an immersive gaming experience. Its customizable RGB lighting and premium materials offer a stylish aesthetic that appeals to a wide range of users.

All three models utilize advanced connectivity options such as Wi-Fi 6 and Bluetooth 5.0, ensuring fast and stable connections. High-capacity batteries and power-efficient components enhance battery life across the series, allowing users to work or play for extended periods without interruption. With robust security features incorporated into the Genie devices, including biometric authentication and hardware encryption, users can feel confident in the safety of their data.

In summary, the Genie PCG, H, and GCG showcase the latest in technology and design, offering tailored experiences for professional, personal, and gaming use. Each model embodies the balance between cutting-edge performance and user-centric features, making them compelling choices in today's competitive computing landscape.