Genie 3042 manual Overview Remotes and Options, Hold, Press both, Simultaneously on

Page 15
Three Button
Remote

5 OVERVIEW - REMOTES AND OPTIONS

WARNING

A moving door can cause serious injury or death.

1.Keep people clear of opening while door is moving.

2.Do NOT allow children to play with opener, including wall console, remote, or wireless keypad.

3.During programming, the door opener could begin to run, so keep people and objects away from the moving door and its parts. To keep the door from moving, close the door and disconnect it from the rail carriage by pulling the Emergency Release Handle. See page 19 for Release Handle operation.

LOST OR STOLEN REMOTE - CLEARING MEMORY

Clearing remotes from powerhead memory will clear ALL programmed remotes and wireless keypad.

NOTE: Follow the PROGRAM REMOTE TO POWERHEAD steps to re-enter remaining or new remotes. See page 9.

 

 

 

PROGRAM

+

1. Press

PROGRAM

and hold

 

—

SET

 

SET

until both lights come ON BLUE. Release button.

FIG. 5-1 Remote

See page 21 for battery changing instructions.

PROGRAM

3.Press SET again and long LED flashes

PURPLE.

2.Lights go out and Round BLUE light comes ON.

PROGRAM

+

 

—

 

SET

FCC and IC CERTIFIED

This device complies with FCC Part 15 and RSS

210 of Industry Canada. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which may be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures:

•Re-orient or relocate the receiver antenna.

•Increase the separation between the opener and receiver.

•Connect the opener into an outlet on a circuit different from that to which the receiver is connected.

•Consult your local dealer.

4.

Press both and

PROGRAM

+

 

 

 

 

simultaneously on the

 

—

 

 

 

powerhead and hold until both LEDs flash BLUE.

•Verify memory is cleared. Press a remote button that was previously programmed to the powerhead. Remote will not activate door opener.

•Garage door opener will operate normally using wall console.

•Program remaining or new remotes as shown on page 9. Your door opener will no longer recognize any signal received from the missing remote, or any other which has not been reprogrammed to the powerhead.

©2011 The Genie Company

3/2011

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Operation and Maintenance Manual Prevention Potential HazardSafety Features Opener FeaturesTable of Contents Infrared Protection Function Important Installation InstructionsSee Both Programming Limits & ForceClose Door Travel Limit Carriage, do so nowOpen Door Travel Limit Door ClosesDoor Opens Adjustment TestKeep people clear of opening while door is moving See round Blue LED come on See both LEDs Flash Blue See both LEDs OFFSee Both Blue LEDs come on See long Purple LED flashing Genie IntelliCode 1 wireless keypadGenie IntelliCode 1 remote See oneRetail Rail Reference Powerhead & Rail Assembled ViewPower Head Professional Installer RailInstallation Typique SUR UNE Porte Sectionelle Header Bracket Mounting Board not provided Typical ONE Piece Door InstallationOverview of Powerhead Controls On powerheadProgramming Buttons location Simultaneously on Overview Remotes and OptionsHold Press both2010 IntelliCode Intellicode FeaturesUse this New IntelliCode 2 openersRead and Follow ALL Instructions Maintenance & TroubleshootingDoor Balance Spring Tension Routine Monthly MaintenanceAdjustment Safe-T-Beam System Check Door balance Contact reverseMotion DETECTOR* Overview Reset OPEN/CLOSE Travel LimitDoor Change Light BulbsControls door opener lights from inside garage Wire routingWall Console Overview Open and closes door from inside garageReplace battery Align components and snap case closed Chain or Belt Tension AdjustmentRemote Battery Replacement Replace remote battery with a CR 2032 coin cell batteryAdjustment Guide Speed Settings Change Speed SettingPowerhead LEDs Round LED Long LED Force Level LED indicator colors Adjustment Guide Force SettingsChange Force Setting Down Force settings within the available rangeProblem What to do Troubleshooting Guide OperationPowerhead LED Possible Problem Solution Opening Cover May Cause Electric Shock Disconnect power from opener prior to removing coverSilentmax Limited Warranty This page left blank This page left blank This page left blank Caractéristiques DU Portier Électrique 19-20 Illustrations d’installations typiques10-11 12-20 Le moteur est branché dans une prise électrique approuvée Avertissementpourréduirelesrisquesdeblessuresgravesoudemort’ALLUMER Programmation DES Limites ET DE LA ForceVoir LES Deux ’ALLUMER RelâchezSur la console de mur Appuyez et Relâchez Ouvrir LA Limite DU TrajetRegarder la porte Se déplacer Les deux bleus Instantanés de LED et Vont AU LoinLE Test D’INVERSION AU Contact Le testAppuyez et Voir les deux DEL Clignoter bleu Programmation DE LA Télécommande À LA Tête D’ALIMENTATIONRépéter au besoin pour dautres télécommandes Voir les deux DEL S’ALLUMER pourpre fermesGenie IntelliCode Clavier sans fil Genie IntelliCodeIntelliCode SET VUE Densemble DES Commandes DE LA Tête D’ALIMENTATIONDéfaut Télécommande Bleu rond Limites Appuyez Programmation Écran DELVUE Densemble Extérieurs ET Options Certifié PAR LA FCC ET ICPourpre LED rouge LES Caractéristiques D’INTELLICODE’ÉQUILIBRE DE LA Porte Entretien ET DépannageConserver CES Instructions Entretien DE Routine MensuelActivez le courant à l’ouvre-porte Changer LES AmpoulesAjustement Coupez lalimentation à l’ouvre-porteFonctionnement PorteNest pas disponible sur tous les modèles Verrouillage DU ChariotLA Console DU MUR VUE Densemble Facultatif Installation Duelle DE Console DE MURRemplacement DE LA Pile Chaîne OU Ajustement DE Tension DE CourroieCorrectement réglé Changement DU Réglage DE Vitesse Changement DU Réglage DE LA Force Des portes avec des caoutchoucs d’étanchéité très raidesAppuyez Program une fois pour écrire le menu de De la console du mur Télécommande La télécommande’ouvre-porte ne Fonctionne PAS à partirDEL de la tête d’alimentation Problème possible Solution Lento Ruidosa ación OpeAzón ninguna sin Se te RfuncionaAda er Te completameZa fue de el Ni Púrpu RojaAzreuf ed leviN Roja Za fue de el Ni RojaSe Azul Roja ElocidadPa elocidad de el Disponibl rangoTarea Bien O AtenciónMotorizada unidad La en cable de ConectorAnteriores límites/fuerza de configuraciones PuertaCarro del Liberación Modelos los todos en disponible NoTa pue la de Ta pue la de eo Balan Ciones Instru AS ArdeTa pue la de eo Balan R6c FIG To ta conde versa Re cIntelliCode = 1/Verde IntelliCode = Rojo SEGIntelliCode en establece Motorizada unidad nueva la para programado haAzul Remoto ControlFIGc Eléctrico Cabezal DEL Controles LOS DE General DescripciónProg Encenderse Control remoto IntelliCodeLibere PresionadoVEA el LED VEA ambos LEDApagados Presione y SE Abre LA Puerta Prueba DE Reversa DE ContactoPrueba AjusteEn la consola de pared Presione y Libere Límite DE Recorrido DEL Abre PuertasObserve el Movimiento de la Puerta Ambos LED se apaganPresionado Libere Configuración Y Prueba DE Límites Y FuerzaProgramación DE Límites Y Fuerza ARAArroja INF Ción TE Cprrde Función NIC ÍndiCar Típicas instalaciones de aciones IlustVerse III erie SODE Intelli 0102/21 YnapmoC eineG ehT Seguridad DE Ción InformMantenimiento DE Y Operación DE Manual / Maintenance DE

3042 specifications

The Genie 3042 is a compact yet powerful telescopic boom lift designed to provide safe and efficient lifting solutions in a variety of applications. This versatile piece of equipment is particularly favored for use in construction, maintenance, and industrial projects where accessibility to heights is essential.

One of the standout features of the Genie 3042 is its impressive working height, reaching up to 12.2 meters (40 feet) and an outreach of up to 6.4 meters (21 feet). This makes it an ideal choice for tasks that require access to elevated work areas, while its narrow frame allows it to navigate through tight spaces with ease.

The machine is equipped with a sturdy platform that can accommodate up to two operators, along with their tools and materials, ensuring efficiency in tasks that require multiple personnel. Safety is a top priority, and the Genie 3042 comes with features such as an automatic level sensor and a load sensing system that ensures the lift operates safely within its intended capacity.

Technologically, the Genie 3042 is built with advanced hydraulic systems that provide smooth and precise boom movements. The lift is powered by a robust engine, which can be electric or bi-energy (dual fuel), offering flexibility depending on the work environment. The electric option is particularly suited for indoor tasks, as it produces zero emissions, while the bi-energy option allows for extended use in outdoor conditions.

Another key characteristic of the Genie 3042 is its ease of transportation. The lift’s compact design and lightweight construction mean that it can be easily towed to various job sites without the need for special permits. Additionally, the non-marking tires protect floors in sensitive environments, making it an excellent choice for indoor applications.

Maintenance is simplified due to the Genie 3042's design, which allows for easy access to key components. This ensures that downtime is minimized, contributing to operational efficiency.

In conclusion, the Genie 3042 is a versatile and feature-rich boom lift that combines height accessibility with safety and ease of use. Its advanced technology, compact design, and various power options make it a reliable choice for various lifting applications in challenging environments.
Top Page Image Contents