Genie 3042 manual Adjustment Guide Speed Settings, Change Speed Setting

Page 22

ADJUSTMENT GUIDE - SPEED SETTINGS

Speed settings are pre-programmed at the factory for the maximum speed. Speed settings should not need adjustment with this unit.

However, travel speed for the opener in both the open and close directions can be adjusted to slower speeds to minimize normal wear for heavy sectional doors.

NOTE: One piece doors are automatically set during Limits programming to the slowest speed and opener speed cannot be reset for one piece doors.

FOR HELP-1-800-35-GENIE OR WWW.GENIECOMPANY.COM

CHANGE SPEED SETTING

Use this guide to ADJUST powerhead SPEED settings.

There are three (3) Speed settings available on this unit for the open and close directions. Door type (one piece or sectional), door weight and balance, and condition of door components / track affect door speed. Speed adjustment may not be available for some installations depending on these factors.

PROGRAM

1.Press on the powerhead and hold until both

SET

lights turn steady ON. Release button.

Lights go out and Round BLUE light comes ON.

2.Press two times and the Round BLUE and Long BLUE lights come ON.

PROGRAM

3.Press once to enter the Speed Programming menu.SET The round LED will flash BLUE 3 times, then the current Speed setting for UP travel will display on the LEDs. See table below.

4.Press to raise or to lower UP Speed settings withinthe available range.

NOTE: Faster door speeds may not be available.

PROGRAM

5.Press SET to set UP Speed level. The long LED will flash BLUE 3 times, then the current Speed setting for DOWN travel will display on the LEDs.

6.Press to raise or to lower DOWN Speed settings within the available range.

NOTE: Faster door speeds may not be available.

PROGRAM

7.Press SET to set DOWN Speed level. Both LEDs flash BLUE to confirm.

Speed Level

Powerhead LEDs

Round LED Long LED

Default LED display is the current Speed setting

Red Red

LED Speed indicator colors

Purple

Purple

Blue Blue

Speed Level LED indicator colors

MAXIMUM

MID

SLOW

Red

Red

ON

ON

Purple

Purple

ON

ON

Blue

Blue

ON

ON

22

©2011 The Genie Company

3/2011

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Operation and Maintenance Manual Potential Hazard PreventionOpener Features Safety FeaturesTable of Contents Important Installation Instructions Infrared Protection FunctionCarriage, do so now Programming Limits & ForceClose Door Travel Limit See BothDoor Closes Open Door Travel LimitDoor Opens Test AdjustmentKeep people clear of opening while door is moving See both LEDs Flash Blue See both LEDs OFF See round Blue LED come onSee Both Blue LEDs come on See one Genie IntelliCode 1 wireless keypadGenie IntelliCode 1 remote See long Purple LED flashingProfessional Installer Rail Reference Powerhead & Rail Assembled ViewPower Head Retail RailInstallation Typique SUR UNE Porte Sectionelle Typical ONE Piece Door Installation Header Bracket Mounting Board not providedOn powerhead Overview of Powerhead ControlsProgramming Buttons location Press both Overview Remotes and OptionsHold Simultaneously onNew IntelliCode 2 openers Intellicode FeaturesUse this 2010 IntelliCodeMaintenance & Troubleshooting Read and Follow ALL InstructionsSafe-T-Beam System Check Door balance Contact reverse Routine Monthly MaintenanceAdjustment Door Balance Spring TensionChange Light Bulbs Reset OPEN/CLOSE Travel LimitDoor Motion DETECTOR* OverviewOpen and closes door from inside garage Wire routingWall Console Overview Controls door opener lights from inside garageReplace remote battery with a CR 2032 coin cell battery Chain or Belt Tension AdjustmentRemote Battery Replacement Replace battery Align components and snap case closedChange Speed Setting Adjustment Guide Speed SettingsPowerhead LEDs Round LED Long LED Down Force settings within the available range Adjustment Guide Force SettingsChange Force Setting Force Level LED indicator colorsTroubleshooting Guide Operation Problem What to doPowerhead LED Possible Problem Solution Disconnect power from opener prior to removing cover Opening Cover May Cause Electric ShockSilentmax Limited Warranty This page left blank This page left blank This page left blank Caractéristiques DU Portier Électrique 12-20 Illustrations d’installations typiques10-11 19-20Avertissementpourréduirelesrisquesdeblessuresgravesoudemort  Le moteur est branché dans une prise électrique approuvée’ALLUMER Relâchez Programmation DES Limites ET DE LA ForceVoir LES Deux ’ALLUMERLes deux bleus Instantanés de LED et Vont AU Loin Ouvrir LA Limite DU TrajetRegarder la porte Se déplacer Sur la console de mur Appuyez et RelâchezLe test LE Test D’INVERSION AU ContactAppuyez et Voir les deux DEL S’ALLUMER pourpre fermes Programmation DE LA Télécommande À LA Tête D’ALIMENTATIONRépéter au besoin pour dautres télécommandes Voir les deux DEL Clignoter bleuClavier sans fil Genie IntelliCode Genie IntelliCodeIntelliCode Appuyez Programmation Écran DEL VUE Densemble DES Commandes DE LA Tête D’ALIMENTATIONDéfaut Télécommande Bleu rond Limites SETCertifié PAR LA FCC ET IC VUE Densemble Extérieurs ET OptionsPourpre LES Caractéristiques D’INTELLICODE LED rougeEntretien DE Routine Mensuel Entretien ET DépannageConserver CES Instructions ’ÉQUILIBRE DE LA PorteCoupez lalimentation à l’ouvre-porte Changer LES AmpoulesAjustement Activez le courant à l’ouvre-porteVerrouillage DU Chariot PorteNest pas disponible sur tous les modèles FonctionnementFacultatif Installation Duelle DE Console DE MUR LA Console DU MUR VUE DensembleChaîne OU Ajustement DE Tension DE Courroie Remplacement DE LA PileCorrectement réglé Changement DU Réglage DE Vitesse Des portes avec des caoutchoucs d’étanchéité très raides Changement DU Réglage DE LA ForceAppuyez Program une fois pour écrire le menu de Fonctionne PAS à partir Télécommande La télécommande’ouvre-porte ne De la console du murDEL de la tête d’alimentation Problème possible Solution Ruidosa ación Ope LentoAzón ninguna sin Te completame RfuncionaAda er Se teZa fue de el Ni Roja RojaAzreuf ed leviN Roja Za fue de el Ni PúrpuDisponibl rango Roja ElocidadPa elocidad de el Se AzulTarea La en cable de Conector AtenciónMotorizada unidad Bien OModelos los todos en disponible No PuertaCarro del Liberación Anteriores límites/fuerza de configuracionesTa pue la de To ta conde versa Re c Ciones Instru AS ArdeTa pue la de eo Balan R6c FIG Ta pue la de eo BalanMotorizada unidad nueva la para programado ha SEGIntelliCode en establece IntelliCode = 1/Verde IntelliCode = RojoRemoto Control AzulEléctrico Cabezal DEL Controles LOS DE General Descripción FIGcProg Presionado Control remoto IntelliCodeLibere EncenderseVEA ambos LED VEA el LEDApagados Presione y Ajuste Prueba DE Reversa DE ContactoPrueba SE Abre LA PuertaAmbos LED se apagan Límite DE Recorrido DEL Abre PuertasObserve el Movimiento de la Puerta En la consola de pared Presione y LibereARA Configuración Y Prueba DE Límites Y FuerzaProgramación DE Límites Y Fuerza Presionado LibereArroja INF Ción TE Cprrde Función Típicas instalaciones de aciones Ilust ÍndiCar NICIII erie S VerseODE Intelli Seguridad DE Ción Inform 0102/21 YnapmoC eineG ehTMantenimiento DE Y Operación DE Manual / Maintenance DE

3042 specifications

The Genie 3042 is a compact yet powerful telescopic boom lift designed to provide safe and efficient lifting solutions in a variety of applications. This versatile piece of equipment is particularly favored for use in construction, maintenance, and industrial projects where accessibility to heights is essential.

One of the standout features of the Genie 3042 is its impressive working height, reaching up to 12.2 meters (40 feet) and an outreach of up to 6.4 meters (21 feet). This makes it an ideal choice for tasks that require access to elevated work areas, while its narrow frame allows it to navigate through tight spaces with ease.

The machine is equipped with a sturdy platform that can accommodate up to two operators, along with their tools and materials, ensuring efficiency in tasks that require multiple personnel. Safety is a top priority, and the Genie 3042 comes with features such as an automatic level sensor and a load sensing system that ensures the lift operates safely within its intended capacity.

Technologically, the Genie 3042 is built with advanced hydraulic systems that provide smooth and precise boom movements. The lift is powered by a robust engine, which can be electric or bi-energy (dual fuel), offering flexibility depending on the work environment. The electric option is particularly suited for indoor tasks, as it produces zero emissions, while the bi-energy option allows for extended use in outdoor conditions.

Another key characteristic of the Genie 3042 is its ease of transportation. The lift’s compact design and lightweight construction mean that it can be easily towed to various job sites without the need for special permits. Additionally, the non-marking tires protect floors in sensitive environments, making it an excellent choice for indoor applications.

Maintenance is simplified due to the Genie 3042's design, which allows for easy access to key components. This ensures that downtime is minimized, contributing to operational efficiency.

In conclusion, the Genie 3042 is a versatile and feature-rich boom lift that combines height accessibility with safety and ease of use. Its advanced technology, compact design, and various power options make it a reliable choice for various lifting applications in challenging environments.
Top Page Image Contents