Genie 3042 manual Important Installation Instructions, Infrared Protection Function

Page 5

Begin here after the opener's physical assembly

and installation has been completed.

There are no assembly or installation steps included in this manual. Contact your Genie® Professional Dealer for an installation poster, if required, or visit www.geniecompany.com to download a PDF file.

The following mechanical assembly tasks must be completed before continuing.

Powerhead and rail are bolted to each other (An illustration is shown on page 11) Example illustrations of the following items are shown on pages 12 and 13

Rail end is attached to a header bracket which is attached to the garage door header

Powerhead is attached to a support frame suspended from the ceiling or ceiling joists

Both pieces of door arms are assembled and are attached to the garage door

Safe-T-Beam® sensors installed and wired

Wall console installed and wired (Shown on page 20)

Carriage is engaged to the chain or belt drive (An illustration is shown on page 11)

Powerhead is plugged into an approved power outlet

Begin programming by setting Limits (see next page.)

A PDF VERSION INSTALLATION POSTER IS AVAILABLE AT WWW.GENIECOMPANY.COM

OR CALL 1-800-35-GENIE TO OBTAIN AN EMAIL PDF FILE

IMPORTANT INSTALLATION INSTRUCTIONS

WARNING:Toreducetheriskofsevereinjuryordeath:

1.READ AND FOLLOW ALL SAFETY, INSTALLATION AND OPERATION INSTRUCTIONS. (If you have questions or do not understand an instruction, call The Genie Company.)

2.Install only on a properly balanced sectional or one piece garage door. An improperly balanced door could cause severe injury. Have a trained door system technician make repairs or adjustments to cables, spring assemblies, and other hardware before installing the opener.

3.Remove all ropes and remove or make inoperative all locks connected to the garage door before installing opener.

4.Where possible, install the door opener 7 feet or more above the floor. For products having an emergency release, mount the emergency release within reach but, at least 6 feet above the floor to avoid contact with vehicles to prevent accidental release.

5.Do NOT connect the opener to source of power until instructed to do so.

6.Locate the wall console:

•Within sight of the garage door,

•At minimum height of 5 feet so small children are not able to reach it, and

•Away from all moving parts of the door.

7.Install the Entrapment WARNING Label next to the wall console in a prominent location.

8.After installing the opener, the door must reverse within 2 seconds when it contacts a 1-1/2 inch high object (or a 2 x 4 board laid flat) on the floor.

INFRARED PROTECTION FUNCTION

1.When garage door is opening, its movement will not be influenced if the Safe-T-Beam® is obstructed.

2.If the Safe-T-Beam® is obstructed before the garage door fully closes, the door will not close.

3.When the garage door is closing, if Safe-T-Beam® is interrupted by person or obstacle, the garage door will stop its downward travel and reverse automatically to its fully opened position.

4.Remove Safe-T-Beam® obstruction.

5.If the Safe-T-Beam® System fails, loses power, or is installed improperly, press and hold the wall console "open/close" button until the door reaches its fully closed position. If you release the "open/close" button on the wall console during the closing movement the door will reverse automatically to its fully opened position.

©2011 The Genie Company

3/2011

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Operation and Maintenance Manual Prevention Potential HazardSafety Features Opener FeaturesTable of Contents Infrared Protection Function Important Installation InstructionsClose Door Travel Limit Programming Limits & ForceCarriage, do so now See BothDoor Opens Open Door Travel LimitDoor Closes Keep people clear of opening while door is moving AdjustmentTest See Both Blue LEDs come on See round Blue LED come onSee both LEDs Flash Blue See both LEDs OFF Genie IntelliCode 1 remote Genie IntelliCode 1 wireless keypadSee one See long Purple LED flashingPower Head Reference Powerhead & Rail Assembled ViewProfessional Installer Rail Retail RailInstallation Typique SUR UNE Porte Sectionelle Header Bracket Mounting Board not provided Typical ONE Piece Door InstallationProgramming Buttons location Overview of Powerhead ControlsOn powerhead Hold Overview Remotes and OptionsPress both Simultaneously onUse this Intellicode FeaturesNew IntelliCode 2 openers 2010 IntelliCodeRead and Follow ALL Instructions Maintenance & TroubleshootingAdjustment Routine Monthly MaintenanceSafe-T-Beam System Check Door balance Contact reverse Door Balance Spring TensionDoor Reset OPEN/CLOSE Travel LimitChange Light Bulbs Motion DETECTOR* OverviewWall Console Overview Wire routingOpen and closes door from inside garage Controls door opener lights from inside garageRemote Battery Replacement Chain or Belt Tension AdjustmentReplace remote battery with a CR 2032 coin cell battery Replace battery Align components and snap case closedPowerhead LEDs Round LED Long LED Adjustment Guide Speed SettingsChange Speed Setting Change Force Setting Adjustment Guide Force SettingsDown Force settings within the available range Force Level LED indicator colorsProblem What to do Troubleshooting Guide OperationPowerhead LED Possible Problem Solution Opening Cover May Cause Electric Shock Disconnect power from opener prior to removing coverSilentmax Limited Warranty This page left blank This page left blank This page left blank Caractéristiques DU Portier Électrique 10-11 Illustrations d’installations typiques12-20 19-20 Le moteur est branché dans une prise électrique approuvée AvertissementpourréduirelesrisquesdeblessuresgravesoudemortVoir LES Deux Programmation DES Limites ET DE LA Force’ALLUMER Relâchez ’ALLUMERRegarder la porte Se déplacer Ouvrir LA Limite DU TrajetLes deux bleus Instantanés de LED et Vont AU Loin Sur la console de mur Appuyez et RelâchezAppuyez et LE Test D’INVERSION AU ContactLe test Répéter au besoin pour dautres télécommandes Programmation DE LA Télécommande À LA Tête D’ALIMENTATIONVoir les deux DEL S’ALLUMER pourpre fermes Voir les deux DEL Clignoter bleuIntelliCode Genie IntelliCodeClavier sans fil Genie IntelliCode Défaut Télécommande Bleu rond Limites VUE Densemble DES Commandes DE LA Tête D’ALIMENTATIONAppuyez Programmation Écran DEL SETPourpre VUE Densemble Extérieurs ET OptionsCertifié PAR LA FCC ET IC LED rouge LES Caractéristiques D’INTELLICODEConserver CES Instructions Entretien ET DépannageEntretien DE Routine Mensuel ’ÉQUILIBRE DE LA PorteAjustement Changer LES AmpoulesCoupez lalimentation à l’ouvre-porte Activez le courant à l’ouvre-porteNest pas disponible sur tous les modèles PorteVerrouillage DU Chariot FonctionnementLA Console DU MUR VUE Densemble Facultatif Installation Duelle DE Console DE MURCorrectement réglé Remplacement DE LA PileChaîne OU Ajustement DE Tension DE Courroie Changement DU Réglage DE Vitesse Appuyez Program une fois pour écrire le menu de Changement DU Réglage DE LA ForceDes portes avec des caoutchoucs d’étanchéité très raides ’ouvre-porte ne Télécommande La télécommandeFonctionne PAS à partir De la console du murDEL de la tête d’alimentation Problème possible Solution Azón ninguna sin LentoRuidosa ación Ope Ada er RfuncionaTe completame Se teAzreuf ed leviN Roja RojaZa fue de el Ni Roja Za fue de el Ni PúrpuPa elocidad de el Roja ElocidadDisponibl rango Se AzulTarea Motorizada unidad AtenciónLa en cable de Conector Bien OCarro del Liberación PuertaModelos los todos en disponible No Anteriores límites/fuerza de configuracionesTa pue la de Ta pue la de eo Balan R6c FIG Ciones Instru AS ArdeTo ta conde versa Re c Ta pue la de eo BalanIntelliCode en establece SEGMotorizada unidad nueva la para programado ha IntelliCode = 1/Verde IntelliCode = RojoAzul Remoto ControlProg FIGcEléctrico Cabezal DEL Controles LOS DE General Descripción Libere Control remoto IntelliCodePresionado EncenderseApagados Presione y VEA el LEDVEA ambos LED Prueba Prueba DE Reversa DE ContactoAjuste SE Abre LA PuertaObserve el Movimiento de la Puerta Límite DE Recorrido DEL Abre PuertasAmbos LED se apagan En la consola de pared Presione y LibereProgramación DE Límites Y Fuerza Configuración Y Prueba DE Límites Y FuerzaARA Presionado LibereArroja INF Ción TE Cprrde Función Car ÍndiTípicas instalaciones de aciones Ilust NICODE Intelli VerseIII erie S 0102/21 YnapmoC eineG ehT Seguridad DE Ción InformMantenimiento DE Y Operación DE Manual / Maintenance DE

3042 specifications

The Genie 3042 is a compact yet powerful telescopic boom lift designed to provide safe and efficient lifting solutions in a variety of applications. This versatile piece of equipment is particularly favored for use in construction, maintenance, and industrial projects where accessibility to heights is essential.

One of the standout features of the Genie 3042 is its impressive working height, reaching up to 12.2 meters (40 feet) and an outreach of up to 6.4 meters (21 feet). This makes it an ideal choice for tasks that require access to elevated work areas, while its narrow frame allows it to navigate through tight spaces with ease.

The machine is equipped with a sturdy platform that can accommodate up to two operators, along with their tools and materials, ensuring efficiency in tasks that require multiple personnel. Safety is a top priority, and the Genie 3042 comes with features such as an automatic level sensor and a load sensing system that ensures the lift operates safely within its intended capacity.

Technologically, the Genie 3042 is built with advanced hydraulic systems that provide smooth and precise boom movements. The lift is powered by a robust engine, which can be electric or bi-energy (dual fuel), offering flexibility depending on the work environment. The electric option is particularly suited for indoor tasks, as it produces zero emissions, while the bi-energy option allows for extended use in outdoor conditions.

Another key characteristic of the Genie 3042 is its ease of transportation. The lift’s compact design and lightweight construction mean that it can be easily towed to various job sites without the need for special permits. Additionally, the non-marking tires protect floors in sensitive environments, making it an excellent choice for indoor applications.

Maintenance is simplified due to the Genie 3042's design, which allows for easy access to key components. This ensures that downtime is minimized, contributing to operational efficiency.

In conclusion, the Genie 3042 is a versatile and feature-rich boom lift that combines height accessibility with safety and ease of use. Its advanced technology, compact design, and various power options make it a reliable choice for various lifting applications in challenging environments.
Top Page Image Contents