Genie 3042 Programming Limits & Force, Close Door Travel Limit, Carriage, do so now, See Both

Page 6

6

1 PROGRAMMING LIMITS & FORCE

(Continuing from Installation Poster if provided)

SETTING & TESTING LIMITS AND FORCE

The OPEN (UP) and CLOSE (DOWN) Door Limit positions are controlled by making adjustments using the panel located on the bottom of the powerhead. Begin with Step 1 and continue through Step 10. Door Force is set during the final Open/Close cycle of these steps. The powerhead will automatically set door speed at slow if the distance between limits is less than 6 feet. Once Limits and Force are set DO NOT use theorbuttons to open or close door.

WARNING

•Make sure doorway is in view and clear of obstacles and people to avoid injury or damage to property.

•DO NOT operate this unit from wall console before LIMITS and FORCE are set. Severe damage to the opener can occur.

•The bullet MUST be engaged to carriage BEFORE setting limits. See Installation Poster (if provided) or refer to pages 11 and 19.

©2011 The Genie Company

A) CLOSE DOOR TRAVEL LIMIT

1 PRESS and HOLD

 

NOTE: If bullet has NOT been engaged to

PROGRAM

 

 

 

the carriage, do so now.

 

 

+

 

 

 

 

 

SET

—

Please note that there is a 30 second timeout

 

 

 

 

 

 

 

 

 

between each programming step.

 

 

 

 

A programming timeout during these steps has

 

 

 

 

occured when two RED flashing LEDs appear.

 

 

 

 

In the event of a timeout please restart at Step 1.

SEE BOTH

 

 

 

 

Blue LEDs

 

 

 

 

come ON

 

 

 

2

RELEASE

SEE round

Blue LED come ON

3PRESS and RELEASE

PROGRAM

—

+

 

 

SEE long Blue

LED come ON

If RED LED comes ON - STOP and

exit programming.

4

NOTE: If one or both LEDs come ON RED at this time, Limits programming menu was not entered properly. You must exit programming and restart.

To exit the programming function wait 30 seconds for the programming to time out.

5PRESS and HOLD until door is FULLY CLOSED then RELEASE

RAM

 

 

 

G

 

—

+

 

 

 

SE

 

 

 

 

PROGRAM

PRESS and

RELEASE

3/2011

SET

—

SEE round Blue LED flashing

Watch door move

NOTE: You can start and stop door

movement using either buttons until door is in correct open or closed position.

OT CE

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Operation and Maintenance Manual Potential Hazard PreventionOpener Features Safety FeaturesTable of Contents Important Installation Instructions Infrared Protection FunctionCarriage, do so now Programming Limits & ForceClose Door Travel Limit See BothOpen Door Travel Limit Door ClosesDoor Opens Adjustment TestKeep people clear of opening while door is moving See round Blue LED come on See both LEDs Flash Blue See both LEDs OFFSee Both Blue LEDs come on See one Genie IntelliCode 1 wireless keypadGenie IntelliCode 1 remote See long Purple LED flashingProfessional Installer Rail Reference Powerhead & Rail Assembled ViewPower Head Retail RailInstallation Typique SUR UNE Porte Sectionelle Typical ONE Piece Door Installation Header Bracket Mounting Board not providedOverview of Powerhead Controls On powerheadProgramming Buttons location Press both Overview Remotes and OptionsHold Simultaneously onNew IntelliCode 2 openers Intellicode FeaturesUse this 2010 IntelliCodeMaintenance & Troubleshooting Read and Follow ALL InstructionsSafe-T-Beam System Check Door balance Contact reverse Routine Monthly MaintenanceAdjustment Door Balance Spring TensionChange Light Bulbs Reset OPEN/CLOSE Travel LimitDoor Motion DETECTOR* OverviewOpen and closes door from inside garage Wire routingWall Console Overview Controls door opener lights from inside garageReplace remote battery with a CR 2032 coin cell battery Chain or Belt Tension AdjustmentRemote Battery Replacement Replace battery Align components and snap case closedAdjustment Guide Speed Settings Change Speed SettingPowerhead LEDs Round LED Long LED Down Force settings within the available range Adjustment Guide Force SettingsChange Force Setting Force Level LED indicator colorsTroubleshooting Guide Operation Problem What to doPowerhead LED Possible Problem Solution Disconnect power from opener prior to removing cover Opening Cover May Cause Electric ShockSilentmax Limited Warranty This page left blank This page left blank This page left blank Caractéristiques DU Portier Électrique 12-20 Illustrations d’installations typiques10-11 19-20Avertissementpourréduirelesrisquesdeblessuresgravesoudemort  Le moteur est branché dans une prise électrique approuvée’ALLUMER Relâchez Programmation DES Limites ET DE LA ForceVoir LES Deux ’ALLUMERLes deux bleus Instantanés de LED et Vont AU Loin Ouvrir LA Limite DU TrajetRegarder la porte Se déplacer Sur la console de mur Appuyez et RelâchezLE Test D’INVERSION AU Contact Le testAppuyez et Voir les deux DEL S’ALLUMER pourpre fermes Programmation DE LA Télécommande À LA Tête D’ALIMENTATIONRépéter au besoin pour dautres télécommandes Voir les deux DEL Clignoter bleuGenie IntelliCode Clavier sans fil Genie IntelliCodeIntelliCode Appuyez Programmation Écran DEL VUE Densemble DES Commandes DE LA Tête D’ALIMENTATIONDéfaut Télécommande Bleu rond Limites SETVUE Densemble Extérieurs ET Options Certifié PAR LA FCC ET ICPourpre LES Caractéristiques D’INTELLICODE LED rougeEntretien DE Routine Mensuel Entretien ET DépannageConserver CES Instructions ’ÉQUILIBRE DE LA PorteCoupez lalimentation à l’ouvre-porte Changer LES AmpoulesAjustement Activez le courant à l’ouvre-porteVerrouillage DU Chariot PorteNest pas disponible sur tous les modèles FonctionnementFacultatif Installation Duelle DE Console DE MUR LA Console DU MUR VUE DensembleRemplacement DE LA Pile Chaîne OU Ajustement DE Tension DE CourroieCorrectement réglé Changement DU Réglage DE Vitesse Changement DU Réglage DE LA Force Des portes avec des caoutchoucs d’étanchéité très raidesAppuyez Program une fois pour écrire le menu de Fonctionne PAS à partir Télécommande La télécommande’ouvre-porte ne De la console du murDEL de la tête d’alimentation Problème possible Solution Lento Ruidosa ación OpeAzón ninguna sin Te completame RfuncionaAda er Se teZa fue de el Ni Roja RojaAzreuf ed leviN Roja Za fue de el Ni PúrpuDisponibl rango Roja ElocidadPa elocidad de el Se AzulTarea La en cable de Conector AtenciónMotorizada unidad Bien OModelos los todos en disponible No PuertaCarro del Liberación Anteriores límites/fuerza de configuracionesTa pue la de To ta conde versa Re c Ciones Instru AS ArdeTa pue la de eo Balan R6c FIG Ta pue la de eo BalanMotorizada unidad nueva la para programado ha SEGIntelliCode en establece IntelliCode = 1/Verde IntelliCode = RojoRemoto Control AzulFIGc Eléctrico Cabezal DEL Controles LOS DE General DescripciónProg Presionado Control remoto IntelliCodeLibere EncenderseVEA el LED VEA ambos LEDApagados Presione y Ajuste Prueba DE Reversa DE ContactoPrueba SE Abre LA PuertaAmbos LED se apagan Límite DE Recorrido DEL Abre PuertasObserve el Movimiento de la Puerta En la consola de pared Presione y LibereARA Configuración Y Prueba DE Límites Y FuerzaProgramación DE Límites Y Fuerza Presionado LibereArroja INF Ción TE Cprrde Función Típicas instalaciones de aciones Ilust ÍndiCar NICVerse III erie SODE Intelli Seguridad DE Ción Inform 0102/21 YnapmoC eineG ehTMantenimiento DE Y Operación DE Manual / Maintenance DE

3042 specifications

The Genie 3042 is a compact yet powerful telescopic boom lift designed to provide safe and efficient lifting solutions in a variety of applications. This versatile piece of equipment is particularly favored for use in construction, maintenance, and industrial projects where accessibility to heights is essential.

One of the standout features of the Genie 3042 is its impressive working height, reaching up to 12.2 meters (40 feet) and an outreach of up to 6.4 meters (21 feet). This makes it an ideal choice for tasks that require access to elevated work areas, while its narrow frame allows it to navigate through tight spaces with ease.

The machine is equipped with a sturdy platform that can accommodate up to two operators, along with their tools and materials, ensuring efficiency in tasks that require multiple personnel. Safety is a top priority, and the Genie 3042 comes with features such as an automatic level sensor and a load sensing system that ensures the lift operates safely within its intended capacity.

Technologically, the Genie 3042 is built with advanced hydraulic systems that provide smooth and precise boom movements. The lift is powered by a robust engine, which can be electric or bi-energy (dual fuel), offering flexibility depending on the work environment. The electric option is particularly suited for indoor tasks, as it produces zero emissions, while the bi-energy option allows for extended use in outdoor conditions.

Another key characteristic of the Genie 3042 is its ease of transportation. The lift’s compact design and lightweight construction mean that it can be easily towed to various job sites without the need for special permits. Additionally, the non-marking tires protect floors in sensitive environments, making it an excellent choice for indoor applications.

Maintenance is simplified due to the Genie 3042's design, which allows for easy access to key components. This ensures that downtime is minimized, contributing to operational efficiency.

In conclusion, the Genie 3042 is a versatile and feature-rich boom lift that combines height accessibility with safety and ease of use. Its advanced technology, compact design, and various power options make it a reliable choice for various lifting applications in challenging environments.
Top Page Image Contents