Middleby Marshall PS360WB, PS360Q, PS360S, PS310, PS314 installation manual Installation

Page 6

ENGLISH

SECTION 2 - INSTALLATION

WARNING - After any conversions, readjustments, or service work on the oven:

Perform a gas leak test.

Test for correct air supply, particularly to the burner blower.

Test for proper combustion and gas supply.

Check that the ventilation system is in operation.

WARNING

Keep the appliance area free and clear of combustibles.

WARNING

The oven must be installed on an even (level) non-flammable flooring and any adjacent walls must be non-flammable. Recommended minimum clearances are specified in the Description section of this Manual.

WARNING

Do not obstruct the flow of combustion and ventilation air to and from your oven. There must be no obstructions around or underneath the oven. Constructional changes to the area where the oven is installed shall not affect the air supply to the oven.

CAUTION

For additional installation information, refer to the following documents:

PS360 Pre-Installation Procedures Manual (Middleby Marshall P/N 88210-0024)

PS360 Installation Manual (Middleby Marshall P/N 88210-0025)

Or, contact your local Authorized Service Agent.

NOTE

There must be adequate clearance between the oven and combustible construction. Clearance

must also be provided for servicing and for proper operation.

NOTE

An electrical wiring diagram for the oven is located inside the machinery compartment or control

compartment.

NOTE

All aspects of the oven installation, including placement, utility connections, and ventilation requirements, must conform with any applicable local, national, or international codes. These codes supercede the require- ments and guidelines provided in this manual.

NOTE

In U.S.A., the oven installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1. The oven, when installed, must be electrically grounded in accor- dance with local codes, or in the absence of local codes, with the National Electrical Code (NEC), or ANSI/ NFPA70.

NOTE

In Canada, the oven installation must conform with local codes, or in the absence of local codes, with the Natural Gas Installation Code, CAN/CGA-B149.1, or the Propane Gas Installation Code, CAN/CGA-B149.2, as applicable. The oven, when installed, must be electrically grounded in accordance with local codes, or in the absence of local codes, with the Canadian Electrical Code CSA, C22.2, as applicable.

NOTE

For Australian installation, the oven installation must conform with AGA Code, AG601, and with any require-

ments of the appropriate statutory authority.

6

Image 6
Contents Owners Operating English Table of Contents Oven Uses III Oven SpecificationsDescription Conveyor Drive Motor Moves the conveyorPS310 PS314 PS360/360Q/360S WeightShipping Weight PS360WB70Installation Additional installation kit components for gas ovens Installation KITInstallation kit components one kit required per cavity 811Recommendations II. Ventilation SystemRequirements Other ventilation concernsStacking III. AssemblyIV. Thermocouple Installation StandsLeftoven Rightoven Tandem Oven AssemblyOven Positioning and Alignment Be pre-mounted to Either of the oven CavitiesFrame of the right oven, pointing outward as shown Push the ovens together. Check that the mounting boltsReplace the rear axial cooling fans. See Figure VI. Conveyor Installation InstallingtheConveyor-AllovensEXCEPTTandem modelsLift the conveyor and position it in the oven as shown Link Orientation Tandem Oven Heavy-Duty VII. Final AssemblyInstalling the Conveyor and Belt Tandem oven models Conveyor FrameAdditional Information Electric Ovens Additional Information Gas OvensConnection Gas Meter DuringpressuretestingnoteoneofthefollowingIf incoming pressure is over 14 W.C mbar, a sepa Gas LineOperation Location and Description of ControlsII. Normal Operation STEP-BY-STEP DailystartupprocedureDailyshutdownprocedure Display, and wait forIII. Quick Reference Digital Temperature Controller Actual TempQuick Reference Troubleshooting Oven will not heat Controls may be set incor RectlyMaintenance Maintenance Daily Cooling Fan/Vent Locations PS360EWBII. Maintenance Monthly Removing Air Fingers and PlatesSplit Belt Idler Shaft Key Spare Parts Kit components all ovens Additional Key Spare Parts Kit components for gas ovensManuel D’INSTALLATION Avertissement Table DES Matières OpérationEntretien Profondeur hors-tout Dégagements minimums recommandésHauteur hors-tout Longueur hors-toutPoids à l’expédition Principale De commande Phase Fréq Courant Pôles CâblagePoids Vol. emballage d’expédition 105 pi3/2,98 m3Mise EN Garde Trousse D’INSTALLATION Description NuméroDepièce Exigences RecommandationsII. Système DE Ventilation Autres considérations pour la ventilationSuperposition IV. Installation DU ThermocoupleIII. Assemblage SoclesAssemblage DES Fours EN Tandem Mise en place et alignement du fourFour Fourdroit Gauche Boulons et entretoises 10 Alignement des parties du fourVI. Installation DU Transporteur 12 Dépose de la roue d’entraînement du TransporteurIntérieur Maillon extérieurMise EN Garde Mise EN Garde Emplacement ET Description DES Commandes FonctionnementRégulateur de température électronique Mise EN Garde En cas de panne d’électricité, mettez toutes les commandesII. Fonctionnement Normal PAS-À-PAS Procéduresquotidiennesdemiseenmarche« Actual Temp »Chaîne d’entraînement Consultation Rapide Dépannage« on » ou « I ». Cette De cuisson sont correctsEntretien Entretien Quotidien AvantII. Entretien Mensuel III. Entretien Trimestriel Service dassistance téléphonique 24 heures Manual DE Operación Precaución SECCIÓN2-INSTALACIÓN Índice DE MateriasSECCIÓN1-DESCRIPCIÓN SECCIÓN3-OPERACIÓNSección 1 Descripción III. Especificaciones DEL HornoVol. de la Caja de Envío PesoPeso de Envío Entrada Nominal de CalorSeccion 2 Instalación NotaHornoInferior DePieza Juego DE InstalaciónDescripción Número DescripciónRequisitos Otros problemas de ventilaciónII. Sistema DE Ventilación RecomendacionesApilado III. EnsambladoIV. Instalación DEL Termopar BasesEnsamblado DEL Horno EN Tándem Horno Izquierdo DerechoFigura 2-9 Pernos y Espaciadores Figura 2-10 Alineamiento de las SeccionesEn ambos extremos del bastidor. Todos los otros hornos VI. Instalación DEL TransportadorNota SolamenteDe horno en tándem para Impulsión para bastidorEslabón Maestro Externo Servicio pesado BastidorFigura 2-23 Placa Informativa del Horno 130 VCAPrecaución Durante LAS Pruebas DE Presión Observe LOSiguiente Sección 3 Operación Ubicación Y Descripción DE LOS ControlesPrecaucion II. Operación Normal Paso a PasoImportante ProcedimientodiariodeencendidoIII. Referencia Rápida Controlador Digital DE Temperatura Síntoma Problema Solución Referencia Rápida Diagnóstico DE AveríasSección 4 Mantenimiento Mantenimiento Diario II. Mantenimiento Mensual Figura 4-4 Remoción de los dedos de aire y placasIII. Mantenimiento Trimestral IV. Mantenimiento Semestral Figura 4-6 Eje loco de banda dobleImportante
Related manuals
Manual 32 pages 51.57 Kb Manual 181 pages 6.17 Kb Manual 4 pages 19.11 Kb

PS314, PS310, PS360S, PS360Q, PS360 specifications

The Middleby Marshall PS360 is a cutting-edge conveyor oven that revolutionizes the way restaurants and commercial kitchens approach food preparation. Specifically designed to enhance efficiency and optimize cooking processes, this oven has gained recognition for its ability to deliver consistently high-quality results in a fast-paced environment.

One of the standout features of the PS360 is its innovative design that incorporates advanced forced air technology. This technology ensures even heat distribution throughout the cooking chamber, resulting in perfectly cooked pizzas, sandwiches, and other menu items without the need for frequent rotation. The forced air system also reduces cooking times, allowing for increased output, making it ideal for high-demand settings such as pizzerias and fast-casual dining establishments.

The PS360 is equipped with a user-friendly digital control panel that allows chefs to easily monitor and adjust cooking temperatures and times. This interface offers precise control over the cooking process, enabling users to customize settings based on specific recipes and customer preferences. Additionally, the oven features a range of programmable settings, allowing for quick adjustments that cater to varying menu items.

Another notable characteristic of the PS360 is its durable construction. Built with high-quality materials, it is designed to withstand the rigors of a busy kitchen environment. Its stainless steel exterior not only adds to its aesthetic appeal but also ensures easy cleaning and maintenance.

Safety is also a paramount concern for the Middleby Marshall PS360. The oven is designed with built-in safety features, including safety locks and temperature alerts, which help prevent accidents and ensure safe operation. The design also accommodates ventilation needs while maximizing energy efficiency, offering a sustainable solution for restaurants looking to reduce their carbon footprint.

Moreover, the PS360 is capable of handling a wide variety of menu items, from traditional pizzas to baked goods and roasted vegetables, making it a versatile addition to any kitchen. The ability to cook multiple items simultaneously streamlines kitchen operations and increases productivity.

In summary, the Middleby Marshall PS360 is a powerful and versatile conveyor oven that combines advanced technology, user-friendly features, and durable design. It enhances cooking efficiency, ensures consistent quality, and supports restaurants in delivering exceptional dishes to their customers. Whether for high-volume operations or varied menu needs, the PS360 stands out as an invaluable tool in commercial kitchens.