Southbend G-72-M, HDG-60-M, HDG-72-RE, HDG-36-RE Installation on Floor Stand 24, 36, and 48 Models

Page 13

HEAVY DUTY COUNTERLINE

INSTALLATION

Step 2d: Installation on Floor Stand (24", 36", and 48" Models)

The 24", 36", and 48" appliances may be installed on top of an optional floor stand (for 60" and 72" griddles, go to Step 2e on page 15). The floor stand is shipped in a separate crate and must be assembled, as follows:

1.Position the bottom-brace pieces on a flat surface, as shown in Figure 8 below. There are two bottom- side braces (items “A”), a bottom-front brace (item “B”), and an identical bottom-rear brace (item “B”).

2.Position a corner brace (item “C”) in each corner, matching the pre-punched holes on the lower inside flange of the bottom braces.

3.Position a leg bracket (item “D”) into each corner. Be sure that the bracket flanges are engaged into the open hem of the bottom braces.

4.Use the sixteen 1/2"-long hex head bolts (items “E”), lock washers (items “F”), and acorn nuts (items “G”) to bolt the corner braces to the bottom braces. Only hand-tighten for now.

5.Check that the leg brackets are in the proper position, and that the outside corners are square.

Figure 8

A

E

C

F

G

D

B

C

D

A

6.Use the eight 1-1/2" hex bolts (items “H” in Figure 9) to attach the two left-legs (items “I”) and the two right-legs (items “J”). “Left” and “right” are as seen from the front or rear of the stand. Be sure that the small threaded-insert near the top of each leg faces either the front or the rear of the stand, not a side. Insert the bolts through the leg brackets and into the legs. Only hand-tighten the bolts for now.

OWNERS MANUAL 1182845 REV 8

PAGE 13

INSTALLATION

Image 13
Contents Heavy Duty Counterline Safety Precautions Table of Contents GAS Supply SpecificationsVentilation ClearancesModel Width Number and Size of Burners Total BTU Dimensions of Griddle ModelsConstruction of Griddle Models Dimensions of Charbroiler ModelsConstruction of Charbroiler Models Dimensions of Open TOP ModelsConstruction of Open TOP Models Unpack InstallationAttach Countertop Legs, Mount on Counter, or Mount on Stand Installation on Countertop Legs Installation Installation on Insulated Base Installation on Floor Stand 24, 36, and 48 Models Owner ’S Manual 1182845 REV Installation on Floor Stand 60 and 72 Models Installation Attach Restraint for Appliances Mounted on Casters Connect Gas Supply Check Pilot and Burner Operation Final Positioning, Clearance Check, and Ventilation CheckFinal Installation Steps for Lava-Rock Charbroilers Final Installation Steps for Griddle ModelsLighting After GAS has Been Shut OFF OperationOperation of Thermostatic Griddle Models Operation of Manual Griddle Models Operation of Charbroiler Models Operation of OPEN-TOP Burner Models Daily CleaningOwner ’S Manual 1182845 REV Adjustment of Manifold GAS Pressure AdjustmentsAdjustment of Pilot Flame Charbroiler and OPEN-TOP Models Adjustment of Pilot Flame Griddle ModelsConversion from ONE Type of GAS to Another Adjustment of Burner FlameAdjustment of Griddle Thermostats Problem Look for TroubleshootingParts Index of Parts DiagramsGriddle Chassis Parts See parts list on previous page. Model HDG-24 is shown Thermostatic Griddle Gas System Parts Parts Manual Griddle Gas System Parts See parts list on previous page. Model HDG-36-M is shown Charbroiler Parts Parts Open Top Parts Parts Floor Stand Parts for 24, 36, and 48 Width Units See parts list on previous page. Model HDG-36 is shown Floor Stand Parts for 60 Width Units 1312 Countertop Legs and Insulated-Base Parts Heavy Duty Counterline Heavy Duty Counterline Heavy Duty Counterline Heavy Duty Counterline