Preamp Outputs

Speaker Connections

Turn off all the components in the system before connecting the speakers. The RA-1062 has color-coded speaker connectors on the back panel. These connectors accept bare wire, or connector lugs. (In non-EC markets, the con- nectors also accept dual banana plugs.)

Route the wire from the RA-1062 to the speakers. Give yourself enough slack so you can move the components to allow access to the speaker connectors. If you are using dual banana plugs, connect them to the wires and then plug into the backs of the binding posts. The thumbscrews of the binding posts should be screwed in all the way (clockwise).

If you are using terminal lugs, connect them to the wires. If you are attaching bare wires directly to the binding posts, separate the wire conductors and strip the insulation from the end of each conductor. Be careful not to cut into the wire strands. Unscrew (turn counterclockwise) the binding post thumbscrews. Place the connec- tor lug or wire around the binding post shaft. Turn the thumbscrews clockwise to clamp the connector lug or wire ﬁrmly in place.

NOTE: Be sure there are no loose wire strands that could touch adjacent wires or connectors.

Signal Connections

See Figure 3

The RA-1062 has line level inputs for source components, connections for audio tape decks, and preamp output connections to send signals to an external power ampliﬁer.

NOTE: To prevent loud, potentially damag- ing, noises, make sure the system is turned off when you make any signal connections.

Phono Input and

Ground Connection

Plug the cable from the turntable into the ap- propriate left and right phono inputs. If the turntable has a “ground” wire connect it to the screw terminal to the left of the Phono inputs. It will help prevent hum and noise.

Line Level Inputs

The RA-1062 has three pair of conventional RCA input connectors for line level components such as CD players, video cassette recorders, tuners, Laser Disc players, or DVD players. These inputs are labeled CD, TUNER, AUX.

The left and right channels are clearly labeled and should be connected to the corresponding channels of the source component. The left RCA connectors are white, the right connectors are red. Use high quality RCA cables for connect- ing input source components to the RA-1062. Ask your authorized Rotel dealer for advice about cables.

Recorder Connections

Tape inputs and outputs can be connected to any record/playback device that accepts standard line level analog input and output signals. Typically that will be a conventional tape recorder. There are two sets of tape con- nections on the back panel, labelled TAPE 1 and TAPE 2.

When connecting a recorder to the RA-1062, the outputs of the recorder must be connected to the tape inputs of the RA-1062. Similarly the tape outputs of the RA-1062 must be con- nected to the inputs of the recorder. Be sure to connect the left and right channels of each device to the proper channels on the associ- ated components. Use high quality connecting cables to prevent loss of sound quality.

NOTE: The tape inputs can also be used for standard playback-only source components, omitting the output connections.

The RA-1062 has a pair of preamp outputs that can send a variable gain signal to an external power amp or signal processor. The preamp outputs are standard RCA-type output connectors, compatible with the inputs of most power ampliﬁers. Use high quality cables and be sure to connect the left and right channel outputs of the RA-1062 to the correct channels of the ampliﬁer.

English

AC Power and Control

AC Power Input

Because of its relatively high power rating, the RA-1062 can draw considerable current. Therefore, it should be plugged directly into a 2- pin polarized wall outlet. Do not use an extension cord. A heavy duty multi-tap power outlet strip may be used if it (and the wall outlet) is rated to handle the current demanded by the RA-1062 and all the other components connected to it.

Your RA-1062 is conﬁgured at the factory for the proper AC line voltage in the country where you purchased it (USA: 115 volts/60Hz AC or CE: 230 volts/50 Hz AC). The AC line conﬁguration is noted on a decal on the back panel. Plug the supplied cord into the AC INPUT receptacle on the back of the unit.

NOTE: Should you move your RA-1062 to another country, it is possible to recon- figure your amplifier for use on a different line voltage. Do not attempt to perform this conversion yourself. Opening the enclosure of the RA-1062 exposes you to dangerous voltages. Consult a qualified service person or the Rotel factory service department for information.

If you are going to be away from home for an extended period of time such as a month long vacation, it is a sensible precaution to unplug your audio and video components while you are away.

POWER Button

Power Indicator

Press the front panel POWER button, to turn the RA-1062 on. The power indicator light is illumi- nated when the RA-1062 is on. Press POWER button again to turn the RA-1062 off.

Once the RA-1062 has been turned on with the front panel button, it can be switched between normal operating mode and standby mode with the POWER button on the RR-AT94 remote control.

RA-1062 specifications

The Rotel RA-1062 is a sophisticated integrated amplifier that embodies the brand's commitment to high-quality audio performance. Designed for music enthusiasts, this model balances powerful output with refined sound quality, making it a versatile choice for various audio setups.

At the heart of the RA-1062 lies a robust power amplifier section, delivering 60 watts per channel into 8 ohms. This allows it to drive a wide range of speakers with ease, ensuring clear and dynamic sound reproduction across different volumes. The amplifier employs Rotel's proprietary Class AB topology, which offers the efficiency needed for high output while minimizing distortion, resulting in a clean and immersive listening experience.

One of the standout features of the RA-1062 is its extensive connectivity options. It includes multiple analog inputs, allowing users to connect various sources like CD players, turntables, and audio streamers. The phono stage is particularly noteworthy, providing an excellent platform for vinyl enthusiasts to enjoy their record collections with exceptional fidelity. Additionally, the amplifier offers a set of preamp outputs, enabling further expansion with external power amplifiers or subwoofers.

Another key characteristic of the RA-1062 is its meticulous construction and design. Rotel emphasizes quality in both component selection and build, utilizing high-grade capacitors and a sturdy chassis to minimize unwanted resonance and interference. The front panel is user-friendly, featuring a sleek layout with a large volume knob and dedicated source selectors, making it easy to navigate between inputs.

The RA-1062 also integrates Rotel's unique Balanced Transformator technology, which provides improved power supply stability and reduces noise. This ensures that audio signals remain pure and undistorted, regardless of the source material.

Overall, the Rotel RA-1062 combines powerful performance, versatility, and excellent build quality, making it a compelling choice for audiophiles looking to enhance their listening experience. Its ability to deliver both warmth and detail allows it to handle a wide array of musical genres, solidifying its place in high-fidelity audio systems. Whether used in a home theater or a dedicated music room, the RA-1062 stands out as a reliable and high-performing integrated amplifier.