Makita RBC2500 instruction manual Checking the spark plug, Supply of grease to gear case

Page 18

Checking the spark plug

–Only use the supplied universal wrench to remove or to install the spark plug.

–The gap between the two electrodes of the spark plug should be 0.6-0.7mm (0.024”-0.028”). If the gap is too wide or too narrow, adjust it. If the spark plug is clogged with carton or fouled, clean it thoroughly or replace it.

CAUTION : Never touch the spark plug connector while the engine is running (danger of high voltage electric shock).

0.6mm-0.7mm (0.024”-0.028”)

Supply of grease to gear case

Grease hole

–Supply grease (Shell Alvania 3 or equivalent) to the gear case through the grease hole every 30 hours. (Genuine MAKITA grease may be purchased from your MAKITA dealer.)

Suction head in the fuel tank

–The fuel filler (5) of the suction head is used to filler the fuel required by the carburetor.

–A periodical visual inspection of the fuel filter is to be conducted. For that purpose open the tank cap, use a wire hook and pull out the suction head through the tank opening. Filters found to have hardened, been polluted or clogged up are to be replaced.

–Insufficient fuel supply can result in the admissible maximum speed being exceeded. It is therefore important to replace the fuel filter at least quarterly to ensure satisfactory fuel supply to the carburetor.

Cleaning of muffler exhaust port

–Check of muffler exhaust port (6) regularly.

–If it is clogged by carbon deposits, carefully scratch the deposits out with a suitable tool.

Any maintenance of adjustment work that is not included and described in this manual is only to be performed by Authorized Service Agents.

18

Image 18

Contents RBC2500RBC2510 Symbols EnglishIntended use of the machine Safety InstructionsGeneral Instructions Personal protective equipmentRefuelling Kickback Maintenance instructionsMethod of operation Kickback preventionFirst Aid When asking for help, please give the following informationNever straighten or weld damaged cutting tools PackagingTechnical Data RBC2500, RBC2510 RBC2500 RBC2510 ModelDesignation of Parts RBC2500 Handle Type RBC2510 Loop Handle TypeAssembly of Engine and Shaft How to mount the control cableConnection of the switch cord Mounting of Handle For machines with U Handle modelsFor machines with Loop Handle Mounting of Protector Mounting of Cutter Blade or Nylon Cutter Head With the hex wrench still in placeFUELS/REFUELLING Handling fuelFuel and oil mixture Attachment of shoulder strap Points in Operation and HOW to StopCorrect Handling of Machine Detachment Adjustment of LOW-SPEED Rotation Idling Resharpening the Cutting Tool Stopping Operation Replacing the nylon cordServicing Instructions Daily checkup and maintenanceCleaning of air cleaner Servicing InstructionsSupply of grease to gear case Cleaning of muffler exhaust portChecking the spark plug Suction head in the fuel tankMaintenance schedule Fault locationStorage Emission Component Defect Warranty Period Parts CoveredObtaining Warranty Service What is not CoveredOWNER’S Warranty Responsibilities HOW to Make a Claim Français Utilisation spéciale de la machine Consignes DE SécuritéInstructions générales Équipement personnel de protectionRavitaillement Rejet Instructions de maintenanceMéthode dutilisation Prévention contre le rejetPremier secours EmballageCaracteristiques Techniques RBC2500, RBC2510 RBC2500 RBC2510 ModèleNomenclature DES Pièces RBC2500 Poignée en U RBC2510 Poignée SimpleMontage du câble de commande Assemblage DU Moteur ET DE L’ARBRERaccordement de la corde d’interrupteur Pour les modèles à poignée simple Montage DE LA PoignéePour les modèles à polgnée en U Au moteurMontage DU Dispositif DE Protection Montage DE LA Lame DE Coupe OU DE LA Tête DE Coupe À FIL La clé hexgonale étant toujours en placeCARBURANTS/RAVITAILLEMENT Manipulation du carburantMélange dhuile et de carburant Fixation du harnais Manipulation Correcte DE LA MachineConsignes DE Mise EN Marche ET Arrêt DE LA Machine RetraitRéaffûtage DE Loutil DE Coupe Reglage DE LA Marche a Petite Vitesse AU RalentiRemplacement du fil en nylon Tête de coupe à fil en nylonFonctionnement Instructions Relatives AUX Réparations Contrôle et opérations de maintenance réguliersInstructions Relatives AUX Réparations Nettoyage du filtre à airTête daspiration dans le réservoir de carburant Contôle de la bougie dallumageGraissage du carter de la boîte de vitesse Nettoyage de lorifice du pot déchappementRemisage Plan de malntenanceLocalisation des défauts Simbolos Lista de contenidos PáginaUso intentado de la máquina Instrucciones DE SeguridadInstrucciones generales Equipo Personal de ProtecciónReabastecimiento Herramientas de Corte Método de trabajoContragolpe Instrucciones de mantenimientoNunca rectificar o soldar las herramientas de corte dañadas Primeros AuxiliosEmbalaje Datos Técnicos RBC2500, RBC2510 RBC2500 RBC2510 ModeloDenominación DE Partes RBC2500 Manillar en U RBC2510 Manillar en bucleMontaje DE Motor Y EJE Montaje del cable de controlEmpalme del cordón del interruptor Para máquinas con manillar cerrado Montaje DEL ManillarPara máquinas con manillar en U Al motorMontaje DEL Protector Montaje DE LA Hoja DE Corte O Cabezal DE Corte DE Nylon Con la llave hexagonal todavía puestaCOMBUSTIBLES/REABASTECIMIENTO Manipulación del combustibleMezcla de combustible y aceite Colocación de la correa para el hombro USO Correcto DE LA MáquinaPuntos Relacionados CON EL Manejo Y LA Parada SeparaciónAfilar LA Herramienta DE Corte Ajuste DEL Giro a Baja Velocidad RalentíOperación Sustitución del cabezal de NylonInstrucciones DE Servicio Instrucciones DE ServicioLimpieza del filtro de aire Cabezal de succión en el tanque de combustible Comprobación de la BujíaSuministro de grasa a la caja de engranajes Limpieza del orificio de salida del silenciadorAlmacenamiento Esquema de mantenimientoLocalizacion de averias Page 11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502, Japan

Related manuals

Manual 19 pages 44.83 Kb