Makita Essential Maintenance and Storage Tips for Your Trimmer
Page 19

STORAGE

–When the machine is in storage for a long time, drain fuel from the fuel tank and carburetor, as follows: Drain all fuel from the fuel tank. Dispose of properly and in accordance with all local laws.

–Remove the spark plug and a few drops of oil into the spark plug hole. Then, pull the starter gently, so that oil covers the engine inside and tighten

the spark plug.

Drain fuel

Humidity

 

 

–Clear dirt or dust from the cutter blade and outside of engine, wipe them with a oil-immersed cloth and keep the machine in a place as dry as possible.

Maintenance schedule

General

Engine assembly, screws and

Visual inspection for damage and tightness

 

nuts

Check for general condition and security

 

 

 

After each refuelling

Control lever

Functional check

 

I-O switch

Functional check

 

 

 

Daily

Air filter

To be cleaned

 

Cooling air duct

To be cleaned

 

Cutting tool

Check for damage and sharpness

 

Idling speed

Inspection (cutting tool must not move)

 

 

 

Weekly

Spark plug

Inspection, replace if necessary

 

Muffler

Check and if necessary clean the opening

 

 

 

Quarterly

Suction head

To be replaced

 

Fuel tank

To be cleaned

 

 

 

Shuting down procedure

Fuel tank

Empty fuel tank

 

Carburetor

Operate until engine runs out of fuel

 

 

 

Fault location

Fault

Engine not starting or with difficulty

Warm start problems

Engine starts but dies

Insufficient performance

System

Observation

Cause

 

 

 

Ignition system

Ignition spark O.K.

Fault in fuel supply or compression system, mechanical

 

 

defect

 

No ignition spark

I-O switch operated, wiring fault or short circuit, spark

 

 

plug or connector defective, ignition module faulty

Fuel supply

Fuel tank filled

Incorrect choke position, carburetor defective, fuel supply

 

 

line bent or blocked, fuel dirty.

Compression

No compression when

Cylinder bottom gasket defective, crankshaft seals

 

pulled over

damaged, cylinder or piston rings defective or improper

 

 

sealing of spark plug

Mechanical fault

Starter not engaging

Broken starter spring, broken parts inside of the engine

 

Tank filled ignition spark

Carburetor contaminated, must be cleaned

 

existing

 

Fuel supply

Tank filled

Incorrect idling adjustment, carburetor contaminated

 

 

Fuel tank vent defective, fuel supply line interrupted,

 

 

cable or I-O switch faulty

Several systems

Engine idling poor

Air filter contaminated, carburetor contaminated, muffler

may simultaneously

 

clogged, exhaust duct in the cylinder clogged

be affected

 

 

 

 

 

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents RBC2500RBC2510 English SymbolsPersonal protective equipment Safety InstructionsGeneral Instructions Intended use of the machineRefuelling Kickback prevention Maintenance instructionsMethod of operation KickbackPackaging When asking for help, please give the following informationNever straighten or weld damaged cutting tools First AidRBC2500 RBC2510 Model Technical Data RBC2500, RBC2510RBC2500 Handle Type RBC2510 Loop Handle Type Designation of PartsHow to mount the control cable Assembly of Engine and ShaftConnection of the switch cord For machines with U Handle models Mounting of HandleFor machines with Loop Handle Mounting of Protector With the hex wrench still in place Mounting of Cutter Blade or Nylon Cutter HeadHandling fuel FUELS/REFUELLINGFuel and oil mixture Detachment Points in Operation and HOW to StopCorrect Handling of Machine Attachment of shoulder strapResharpening the Cutting Tool Adjustment of LOW-SPEED Rotation IdlingStopping Replacing the nylon cord OperationServicing Instructions Daily checkup and maintenanceCleaning of air cleaner Servicing InstructionsSuction head in the fuel tank Cleaning of muffler exhaust portChecking the spark plug Supply of grease to gear caseFault location Maintenance scheduleStorage Parts Covered Emission Component Defect Warranty PeriodWhat is not Covered Obtaining Warranty ServiceOWNER’S Warranty Responsibilities HOW to Make a Claim Français Équipement personnel de protection Consignes DE SécuritéInstructions générales Utilisation spéciale de la machineRavitaillement Prévention contre le rejet Instructions de maintenanceMéthode dutilisation RejetEmballage Premier secoursRBC2500 RBC2510 Modèle Caracteristiques Techniques RBC2500, RBC2510RBC2500 Poignée en U RBC2510 Poignée Simple Nomenclature DES PiècesAssemblage DU Moteur ET DE L’ARBRE Montage du câble de commandeRaccordement de la corde d’interrupteur Au moteur Montage DE LA PoignéePour les modèles à polgnée en U Pour les modèles à poignée simpleMontage DU Dispositif DE Protection La clé hexgonale étant toujours en place Montage DE LA Lame DE Coupe OU DE LA Tête DE Coupe À FILManipulation du carburant CARBURANTS/RAVITAILLEMENTMélange dhuile et de carburant Retrait Manipulation Correcte DE LA MachineConsignes DE Mise EN Marche ET Arrêt DE LA Machine Fixation du harnaisReglage DE LA Marche a Petite Vitesse AU Ralenti Réaffûtage DE Loutil DE CoupeTête de coupe à fil en nylon Remplacement du fil en nylonFonctionnement Nettoyage du filtre à air Contrôle et opérations de maintenance réguliersInstructions Relatives AUX Réparations Instructions Relatives AUX RéparationsNettoyage de lorifice du pot déchappement Contôle de la bougie dallumageGraissage du carter de la boîte de vitesse Tête daspiration dans le réservoir de carburantPlan de malntenance RemisageLocalisation des défauts Lista de contenidos Página SimbolosEquipo Personal de Protección Instrucciones DE SeguridadInstrucciones generales Uso intentado de la máquinaReabastecimiento Instrucciones de mantenimiento Método de trabajoContragolpe Herramientas de CortePrimeros Auxilios Nunca rectificar o soldar las herramientas de corte dañadasEmbalaje RBC2500 RBC2510 Modelo Datos Técnicos RBC2500, RBC2510RBC2500 Manillar en U RBC2510 Manillar en bucle Denominación DE PartesMontaje del cable de control Montaje DE Motor Y EJEEmpalme del cordón del interruptor Al motor Montaje DEL ManillarPara máquinas con manillar en U Para máquinas con manillar cerradoMontaje DEL Protector Con la llave hexagonal todavía puesta Montaje DE LA Hoja DE Corte O Cabezal DE Corte DE NylonManipulación del combustible COMBUSTIBLES/REABASTECIMIENTOMezcla de combustible y aceite Separación USO Correcto DE LA MáquinaPuntos Relacionados CON EL Manejo Y LA Parada Colocación de la correa para el hombroAjuste DEL Giro a Baja Velocidad Ralentí Afilar LA Herramienta DE CorteSustitución del cabezal de Nylon OperaciónInstrucciones DE Servicio Instrucciones DE ServicioLimpieza del filtro de aire Limpieza del orificio de salida del silenciador Comprobación de la BujíaSuministro de grasa a la caja de engranajes Cabezal de succión en el tanque de combustibleEsquema de mantenimiento AlmacenamientoLocalizacion de averias Page 11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502, Japan
Related manuals
Manual 19 pages 44.83 Kb

RBC2500 specifications

The Makita RBC2510 and RBC2500 are robust string trimmers designed for landscapers and homeowners seeking reliable and efficient tools for garden maintenance. Both models embody Makita's commitment to quality, performance, and user-friendly features, making them popular choices in the outdoor power equipment market.

The RBC2510 features a powerful 25cc 2-stroke engine, delivering optimal cutting performance while maintaining a low weight for better maneuverability. Its lightweight design, weighing approximately 6.4 kg (14.1 lbs) without the cutting equipment, enhances user comfort during prolonged use. The RBC2500, with a similar engine configuration, boasts a 25.4cc power plant that provides ample torque, allowing it to tackle tougher grass and weeds with ease.

These trimmers come equipped with a semi-automatic dual-line cutting head. The tap-and-go system ensures that users can quickly advance the cutting line with a simple tap on the ground, minimizing downtime. The cutting width of both models is around 400mm (15.75 inches), allowing for efficient trimming of larger areas.

One of the standout features of the RBC2510 and RBC2500 is their Easy Start technology. This system reduces the effort required to start the engine, making it particularly attractive for users who may struggle with traditional pull starts. While the RBC2510 employs a spring-assisted starter, the RBC2500 is known for its easy-start mechanism that minimizes tedious starting procedures.

Both models feature an ergonomically designed handle that provides excellent control and comfort, reducing vibrations and allowing for extended use without causing excessive fatigue. Additionally, the adjustable harness available with these trimmers aids in weight distribution, making it easier to handle the equipment for extended periods.

Durability is another key characteristic of the Makita RBC2510 and RBC2500. Built from high-quality materials, these trimmers are designed to withstand harsh outdoor conditions, ensuring longevity and reliability for users. The gear case is constructed to be robust, and the overall design aims to protect the engine and components from damage during operation.

In conclusion, the Makita RBC2510 and RBC2500 string trimmers offer powerful performance, user-friendly features, and robust construction, appealing to both professional landscapers and homeowners. With their advanced technologies and ergonomic designs, these trimmers ensure efficient and comfortable operation, making them invaluable tools for maintaining outdoor spaces.
Top Page Image Contents