Walker MC19 manual Safety Instructions Before Operating, Do not mow with bystanders in the area

Page 13

Safety Instructions - Before Operating

Pay particular attention to any information labeled

DANGER, WARNING, CAUTION, IMPORTANT, and NOTE in this manual.

When you see the Safety Alert Symbol ( ), read, understand, and follow the instructions. Fail­ure to comply with safety instructions may result in person- al injury.

The seriousness or degree of importance of each type of information is defined as follows:

DANGER

An IMMEDIATE hazard that WILL result in severe personal injury or DEATH, if warn- ing is ignored and proper safety precau- tions are not taken.

WARNING

A POTENTIAL hazard that COULD result in severe personal injury or DEATH, if warn- ing is ignored and proper safety precau- tions are not taken.

CAUTION

Possible hazards or unsafe practices that MAY result in MODERATE personal injury or property damage, or machine damage, if warning is ignored and proper safety pre- cautions are not taken.

IMPORTANT:  Identifies mechanical information demanding special attention, since it deals with the possibility of damaging a part or parts of the ma- chine.

NOTE:  Identifies information worthy of special at- tention.

Walker Manufacturing cannot predict every poten- tially dangerous situation. Therefore, items labeled as such in this manual do not cover all conceivable situations. Any person using procedures, tools, or control techniques not recommended by Walker Manufacturing must take full responsibility for safety.

The Walker Rider Lawnmower has been designed with many safety features to protect the operator from personal harm or injury. However, it is necessary for the operator to use safe operating procedures at all times. Failure to follow safety instructions con- tained in this manual may result in personal in- jury or damage to equipment or property.

If you have any questions concerning setup, opera- tion, maintenance, or safety, please contact your authorized Walker Mower dealer or call Walker Manufacturing Company at (970) 221-5614.

BEFORE OPERATING

1.Read and understand the contents of this Operator’s Manual before starting and oper- ating the machine. Become thoroughly famil- iar with all machine controls and how to stop the machine and disengage the controls quickly. Replacement Operator’s Manuals are available by sending the Model and Serial Number to:

Walker Manufacturing Company

5925 East Harmony Road

Fort Collins, CO 80528

2.Never allow children to operate rider mower. Do not allow adults to operate without proper instruction.

3.Clear the area to be mowed of any foreign objects which may be picked up and thrown by cutter blades. Pick up all sticks, stones, wire, and any other debris.

4.Keep everyone, especially children and pets, a safe distance away from the area being mowed.

Do not mow with bystanders in the area.

5.Do not operate the machine barefoot or wearing sandals, sneakers, tennis shoes, or similar lightweight footwear. Wear substantial pro- tective footwear.

9

Image 13
Contents OPERATOR’S Manual Foreword Table of Contents Maintenance Schedule Chart Important Tips for Care Glossary General InformationIdentifying Number Locations Fill In By PurchaserServicing of Engine and Drivetrain Components Engine SpecificationsElectrical System TransmissionTire Size Blade DriveDrive Belts SeatMower Deck GHS SystemFront View and Right Side View Component IdentificationRear View and Left Side View Top View Engine Compartment PTOBefore Operating Safety Instructions Before OperatingDo not mow with bystanders in the area Safety Instructions Before Operating Safety Instructions Operating Safety Instructions Operating Safety Instructions Maintenance Safety Instructions Location Deck Discharge Shield SD Decks Only Part Number Location Each End of Mower Deck Part NumberLocation Catcher Door Hinge Bar LH and RH Sides Part Number Location Right Side, Behind Operator Seat Part NumberSAFETY, CONTROL, and Instruction Decals Setup Instructions Assembly InstructionsBattery Service Wet Battery ServiceBattery Installation Battery ChargingBattery Installation Mower Deck Assembly Deck Caster Wheels InstallationDischarge Shield Installation On Side Discharge Deck Deck Caster Wheel InstallationPTO Shaft Guard Installation PTO Coupler Installation Tool Deck InstallationMower Deck Installation PTO Shaft Connection Quick Disconnect Ring Released Position Deck Counterweight Spring InstallationQuick Disconnect Ring Locked Position Deck Leveling Machine must be shut off during this procedureDeck Leveling Refer to Lubrication for Gear Axle Lubrication Fill Fuel TankBlades in Maintenance Instructions Control IDENTIFICATION, LOCATION, and Function Operating InstructionsEngine Choke Key PositionsChoke and Throttle Location Forward Speed Control FSC Engine ThrottleSteering Levers Blade Clutch PTOLockout Lever Location Parking Brake Disengaged Front Body Latch ReleaseOil Pressure Warning Horn HourmeterOperating Controls Top View from Drivers Point of View Left Wheel Steering LeverStarting the Engine Adjusting Ground Speed and SteeringEngaged Fore Attempting to MOWOperating Instructions Correct Operator Hand Position On the Controls Blade Clutch Disengaged Blade Clutch EngagedStopping the Machine Transmission Lockout Cutting Height AdjustmentLockout Lever Freewheel Position Recommendations for Mowing Lockout Lever Normal Operating PositionNo Driving Zone Side Discharge Deflector Shield Lowest PositionRecommendations for TILT-UP Deck OPERATION/TRANSPORT GHS Flow and Components Blower Intake Cover General InformationRotating Blower Blades Forward Clogging ChecklistBlade Rotation for GHS Mower Deck View from Underneath Powerfil Using the Tilt-Up DeckFull Signal Horn Grass Catcher Screen Removal for CleaningTailgate Dumping Using the Dump BagPositioning Dump Bag on Catcher Dumping Catcher into Dump Bag Maintenance Instructions Important Tips for Care of the Kohler Engine Engine Oil LubricationEach USE Dipstick Operating RangeTurn Oil Drain/Oil Filter LocationMower Deck Gearbox Lubrication DS52 or DS62 Mower Deck Lubrication Changing Gearbox Oil Dipstick Location, Tractor PTO GearboxGear Axle Lubrication RantyGrease Fitting and Oil Point Lubrication Transmission Reservoir Air Bleed Plug LocationLubrication Points for Optional Belt Driven Decks DS62 Shown Chassis and Deck Lubrication Points DS42 Shown Engine Air Cleaner System Components Air Filter Restriction Gauge Location Air Cleaner Components Shown with Cover Being RemovedProper Orientation of Air Cleaner Cover Air Filter Element ReplacementCooling Air Intake System Deck Secured in TILT-UP Position Engine Cooling Air Intake Screen Cooling Fin Access PanelsMaintenance Instructions GHS Exhaust Screen BatteryCHECKING/SERVICING Electrolyte LevelWheel Bolt Torque Charging the BatterySharpen Mower Blades Blade Balanced on Magnetic Wall-Mounted Balancer Mower Blade Profile For SharpeningDrive Belts Spark Plugs Drive Belts There are four 4 individual belts on GHS models REPLACING/REPAIRINGBelt Locations REPLACING/REPAIRINGEngine PTO Drive Belt Removal Engine PTO Drive Belt 3 Groove Power BandJackshaft Drive Belt Disengaged Jackshaft Drive BeltJackshaft Drive Belt Engaged GHS Blower Drive Belt Assembly Engaged GHS Blower Drive Belt Assembly DisengagedHydrostatic Ground Drive Belt Assembly Engaged Hydrostatic Ground Drive Belt Assembly DisengagedBlade Overload Shear Bolts Fuel Filter LocationCutting Blade Shear Bolts PTO Shear Pin Steering Handle Adjustment Tilt-Up Deck Adjustable Stop AdjustmentsSteering Handles Pinch Point Spring Loaded Door Operator’s Notes Operator’s Notes Limited Warranty For Walker Commercial Rider Mower Walker MFG. CO E. Harmony ROAD, Fort COLLINS, CO 80528 970