Walker MC19 manual Safety Instructions Before Operating

Page 14

Safety Instructions - Before Operating

6.Do not wear loose fitting clothing that could get caught in moving parts. Do not operate this ma- chine while wearing shorts; always wear ade- quate protective clothing, including long pants. Wearing safety glasses, safety shoes, and a helmet is advisable and required by some local ordinances and insurance regulations.

7.Prolonged exposure to loud noise can cause impairment or loss of hearing. Operator hear- ing protection is recommended; particularly for continuous operation of the GHS Model due to blower noise level. Wear a suitable hearing protective device, such as earmuffs or earplugs.

8.Keep all protective shields and safety de- vices in place. If a protective shield, safety device, or decal is damaged, unusable, or miss- ing, repair or replace it before operating the machine.

9.Be sure interlock switches are functioning correctly, so the engine cannot be started un- less the Forward Speed Control lever is in the NEUTRAL-PARK position, and the PTO clutch is in the DISENGAGED position. Also, the en- gine should stop if the operator lifts off the seat with either the Forward Speed Control (FSC) out of the NEUTRAL-PARK position or the PTO clutch in the ENGAGED position.

NOTE: There is a 1/2 second time delay func- tion on the seat switch to avoid engine power interruption when driving over bumps.

10.Handle gasoline with care. Gasoline is highly flammable and its vapors are explosive:

a.Use an approved fuel container.

b.Never add fuel to a running engine or hot engine (allow hot engine to cool several min- utes).

c.Keep matches, cigarettes, cigars, pipes, open flames, or sparks away from the fuel tank and fuel container.

d.Always fill the fuel tank outdoors using care. Fill to about one inch from the top of the tank. Use a funnel or spout to prevent spilling.

e.Replace the machine fuel cap and container cap securely and clean up any spilled fuel before starting the engine.

11.Never attempt to make any adjustments while the engine is running, except where specifically instructed to do so.

12.The electrical system battery contains sulfuric acid. Avoid any contact with skin, eyes, and clothing. Keep the battery and acid out of reach of children.

WARNING

The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

10

Image 14
Contents OPERATOR’S Manual Foreword Table of Contents Maintenance Schedule Chart Important Tips for Care Identifying Number Locations General InformationGlossary Fill In By PurchaserServicing of Engine and Drivetrain Components Electrical System SpecificationsEngine TransmissionDrive Belts Blade DriveTire Size SeatGHS System Mower DeckComponent Identification Front View and Right Side ViewRear View and Left Side View PTO Top View Engine CompartmentDo not mow with bystanders in the area Safety Instructions Before OperatingBefore Operating Safety Instructions Before Operating Safety Instructions Operating Safety Instructions Operating Safety Instructions Maintenance Safety Instructions Location Each End of Mower Deck Part Number Location Deck Discharge Shield SD Decks Only Part NumberLocation Right Side, Behind Operator Seat Part Number Location Catcher Door Hinge Bar LH and RH Sides Part NumberSAFETY, CONTROL, and Instruction Decals Battery Service Assembly InstructionsSetup Instructions Wet Battery ServiceBattery Installation Mower Deck Assembly Battery ChargingBattery Installation Deck Caster Wheels InstallationPTO Shaft Guard Installation Deck Caster Wheel InstallationDischarge Shield Installation On Side Discharge Deck Mower Deck Installation PTO Shaft Connection Deck InstallationPTO Coupler Installation Tool Quick Disconnect Ring Locked Position Deck Counterweight Spring InstallationQuick Disconnect Ring Released Position Deck Leveling Machine must be shut off during this procedureDeck Leveling Fill Fuel Tank Refer to Lubrication for Gear Axle LubricationBlades in Maintenance Instructions Engine Choke Operating InstructionsControl IDENTIFICATION, LOCATION, and Function Key PositionsSteering Levers Engine ThrottleChoke and Throttle Location Forward Speed Control FSC Blade Clutch PTOParking Brake Disengaged Front Body Latch Release Lockout Lever LocationHourmeter Oil Pressure Warning HornLeft Wheel Steering Lever Operating Controls Top View from Drivers Point of ViewEngaged Adjusting Ground Speed and SteeringStarting the Engine Fore Attempting to MOWOperating Instructions Correct Operator Hand Position On the Controls Stopping the Machine Blade Clutch EngagedBlade Clutch Disengaged Lockout Lever Freewheel Position Cutting Height AdjustmentTransmission Lockout Lockout Lever Normal Operating Position Recommendations for MowingSide Discharge Deflector Shield Lowest Position No Driving ZoneRecommendations for TILT-UP Deck OPERATION/TRANSPORT GHS Flow and Components Rotating Blower Blades General InformationBlower Intake Cover Blade Rotation for GHS Mower Deck View from Underneath Clogging ChecklistForward Full Signal Horn Using the Tilt-Up DeckPowerfil Grass Catcher Screen Removal for CleaningPositioning Dump Bag on Catcher Using the Dump BagTailgate Dumping Dumping Catcher into Dump Bag Maintenance Instructions Important Tips for Care of the Kohler Engine Each USE LubricationEngine Oil Dipstick Operating RangeMower Deck Gearbox Lubrication Oil Drain/Oil Filter LocationTurn DS52 or DS62 Mower Deck Lubrication Gear Axle Lubrication Dipstick Location, Tractor PTO GearboxChanging Gearbox Oil RantyTransmission Reservoir Air Bleed Plug Location Grease Fitting and Oil Point LubricationLubrication Points for Optional Belt Driven Decks DS62 Shown Chassis and Deck Lubrication Points DS42 Shown Engine Air Cleaner System Components Air Cleaner Components Shown with Cover Being Removed Air Filter Restriction Gauge LocationCooling Air Intake System Air Filter Element ReplacementProper Orientation of Air Cleaner Cover Engine Cooling Air Intake Screen Cooling Fin Access Panels Deck Secured in TILT-UP PositionMaintenance Instructions CHECKING/SERVICING BatteryGHS Exhaust Screen Electrolyte LevelSharpen Mower Blades Charging the BatteryWheel Bolt Torque Drive Belts Mower Blade Profile For SharpeningBlade Balanced on Magnetic Wall-Mounted Balancer Spark Plugs REPLACING/REPAIRING Drive Belts There are four 4 individual belts on GHS modelsREPLACING/REPAIRING Belt LocationsEngine PTO Drive Belt 3 Groove Power Band Engine PTO Drive Belt RemovalJackshaft Drive Belt Engaged Jackshaft Drive BeltJackshaft Drive Belt Disengaged GHS Blower Drive Belt Assembly Disengaged GHS Blower Drive Belt Assembly EngagedHydrostatic Ground Drive Belt Assembly Disengaged Hydrostatic Ground Drive Belt Assembly EngagedCutting Blade Shear Bolts Fuel Filter LocationBlade Overload Shear Bolts PTO Shear Pin Steering Handles AdjustmentsSteering Handle Adjustment Tilt-Up Deck Adjustable Stop Pinch Point Spring Loaded Door Operator’s Notes Operator’s Notes Limited Warranty For Walker Commercial Rider Mower Walker MFG. CO E. Harmony ROAD, Fort COLLINS, CO 80528 970