Walker MC19 Deck Caster Wheel Installation, Discharge Shield Installation On Side Discharge Deck

Page 24

Assembly Instructions

Axle Spacer Tube

Spacer Washer

Axle Bolt

Deck Caster Wheel Installation

5.Grease the caster wheel bearings and caster pivot bearings - one grease fitting for each wheel and each pivot.

Deck Discharge Chute Installation (GHS Rear Discharge Models Only)

Mount the discharge chute hinge on top of the deck discharge opening using the 1/4-20 x 1/2 in. socket button head screw and 1/4-20 ESNA nut. Position the screw with the head inside of the chute and the nut on the outside. Attach spring for tilt-up action from chute to bracket on deck.

 

 

Carrier Frame

 

 

Attach

 

Tube Sockets

 

 

 

 

Attach

Guard

 

 

 

Chute

 

 

 

 

 

Nut on Top

Discharge Chute and PTO Shaft Guard Installation on Rear Discharge Deck

Deck Discharge Deflector Shield Installation (Side Discharge Models Only)

Attach the side discharge deflector shield using two

(2)3/8-16 x 1-1/4 in. bolts, 3/8-16 nylon insert lock- nuts, and 3/8 in. wave spring washers. The wave washers fit between the two hinging surfaces. Tight- en the nuts until the shield moves freely but is not loose.

WARNING

DO NOT operate the machine without the grass deflector shield attached and in the lowest possible position.

Attach Shield

Discharge Shield Installation

on Side Discharge Deck

PTO Shaft Guard Installation

Position the shaft guard as shown and mount with two (2) 1/4-20 x 1/2 in. bolts.

Tilt-Up Roller Wheel Installation

Mount the two (2) tilt-up roller wheels on the brack- ets on the rear skirt of the deck housing using the P/N 8490 axle bolt, 3/8 in. wave spring washer and 3/8-16 in. Whiz locknut. Tighten the axle bolt until the wheel rolls freely, but is not loose.

20

Image 24
Contents OPERATOR’S Manual Foreword Table of Contents Maintenance Schedule Chart Important Tips for Care General Information GlossaryIdentifying Number Locations Fill In By PurchaserServicing of Engine and Drivetrain Components Specifications EngineElectrical System TransmissionBlade Drive Tire SizeDrive Belts SeatGHS System Mower DeckComponent Identification Front View and Right Side ViewRear View and Left Side View PTO Top View Engine CompartmentSafety Instructions Before Operating Before OperatingDo not mow with bystanders in the area Safety Instructions Before Operating Safety Instructions Operating Safety Instructions Operating Safety Instructions Maintenance Safety Instructions Location Each End of Mower Deck Part Number Location Deck Discharge Shield SD Decks Only Part NumberLocation Right Side, Behind Operator Seat Part Number Location Catcher Door Hinge Bar LH and RH Sides Part NumberSAFETY, CONTROL, and Instruction Decals Assembly Instructions Setup InstructionsBattery Service Wet Battery ServiceBattery Charging Battery InstallationBattery Installation Mower Deck Assembly Deck Caster Wheels InstallationDeck Caster Wheel Installation Discharge Shield Installation On Side Discharge DeckPTO Shaft Guard Installation Deck Installation PTO Coupler Installation ToolMower Deck Installation PTO Shaft Connection Deck Counterweight Spring Installation Quick Disconnect Ring Released PositionQuick Disconnect Ring Locked Position Machine must be shut off during this procedure Deck LevelingDeck Leveling Fill Fuel Tank Refer to Lubrication for Gear Axle LubricationBlades in Maintenance Instructions Operating Instructions Control IDENTIFICATION, LOCATION, and FunctionEngine Choke Key PositionsEngine Throttle Choke and Throttle Location Forward Speed Control FSCSteering Levers Blade Clutch PTOParking Brake Disengaged Front Body Latch Release Lockout Lever LocationHourmeter Oil Pressure Warning HornLeft Wheel Steering Lever Operating Controls Top View from Drivers Point of ViewAdjusting Ground Speed and Steering Starting the EngineEngaged Fore Attempting to MOWOperating Instructions Correct Operator Hand Position On the Controls Blade Clutch Engaged Blade Clutch DisengagedStopping the Machine Cutting Height Adjustment Transmission LockoutLockout Lever Freewheel Position Lockout Lever Normal Operating Position Recommendations for MowingSide Discharge Deflector Shield Lowest Position No Driving ZoneRecommendations for TILT-UP Deck OPERATION/TRANSPORT GHS Flow and Components General Information Blower Intake CoverRotating Blower Blades Clogging Checklist ForwardBlade Rotation for GHS Mower Deck View from Underneath Using the Tilt-Up Deck PowerfilFull Signal Horn Grass Catcher Screen Removal for CleaningUsing the Dump Bag Tailgate DumpingPositioning Dump Bag on Catcher Dumping Catcher into Dump Bag Maintenance Instructions Important Tips for Care of the Kohler Engine Lubrication Engine OilEach USE Dipstick Operating RangeOil Drain/Oil Filter Location TurnMower Deck Gearbox Lubrication DS52 or DS62 Mower Deck Lubrication Dipstick Location, Tractor PTO Gearbox Changing Gearbox OilGear Axle Lubrication RantyTransmission Reservoir Air Bleed Plug Location Grease Fitting and Oil Point LubricationLubrication Points for Optional Belt Driven Decks DS62 Shown Chassis and Deck Lubrication Points DS42 Shown Engine Air Cleaner System Components Air Cleaner Components Shown with Cover Being Removed Air Filter Restriction Gauge LocationAir Filter Element Replacement Proper Orientation of Air Cleaner CoverCooling Air Intake System Engine Cooling Air Intake Screen Cooling Fin Access Panels Deck Secured in TILT-UP PositionMaintenance Instructions Battery GHS Exhaust ScreenCHECKING/SERVICING Electrolyte LevelCharging the Battery Wheel Bolt TorqueSharpen Mower Blades Mower Blade Profile For Sharpening Blade Balanced on Magnetic Wall-Mounted BalancerDrive Belts Spark Plugs REPLACING/REPAIRING Drive Belts There are four 4 individual belts on GHS modelsREPLACING/REPAIRING Belt LocationsEngine PTO Drive Belt 3 Groove Power Band Engine PTO Drive Belt RemovalJackshaft Drive Belt Jackshaft Drive Belt DisengagedJackshaft Drive Belt Engaged GHS Blower Drive Belt Assembly Disengaged GHS Blower Drive Belt Assembly EngagedHydrostatic Ground Drive Belt Assembly Disengaged Hydrostatic Ground Drive Belt Assembly EngagedFuel Filter Location Blade Overload Shear BoltsCutting Blade Shear Bolts PTO Shear Pin Adjustments Steering Handle Adjustment Tilt-Up Deck Adjustable StopSteering Handles Pinch Point Spring Loaded Door Operator’s Notes Operator’s Notes Limited Warranty For Walker Commercial Rider Mower Walker MFG. CO E. Harmony ROAD, Fort COLLINS, CO 80528 970