Woods Equipment DS1260Q, DSO1260Q, DS1440Q manual Safety & Instructional Decals, Be Careful

Page 11

(Safety Decals continued on next page)

SAFETY & INSTRUCTIONAL DECALS

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

1 - SERIAL NUMBER PLATE

MODEL NO.	SERIAL NO.
	Woods Equipment Company
	Oregon, Illinois, U.S.A.

2 - PN 5669

3 - PN 12777

4 - PN 1003751

WARNING

CRUSHING AND PINCHING HAZARD

Be extremely careful handling various parts of the machine. They are heavy and hands, fingers, feet, and other body parts could be crushed or pinched between tractor and implement. Operate tractor controls from tractor seat only. Do not stand between tractor and implement when tractor is in gear.

Make sure parking brake is engaged before going between tractor and implement. Stand clear of machine while in operation or when it is being raised or lowered.

FAILURE TO FOLLOW THESE

INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. 1003751-A

BE CAREFUL!

Use a clean, damp cloth to clean safety decals.

Avoid spraying too close to decals when using a pressure washer; high-pressure water can enter through very small scratches or under edges of decals causing them to peel or come off.

Replacement safety decals can be ordered free from your Woods dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319-6637.

MAN0571 (Rev. 6/15//2007)	Safety 11
MAN0571 (Rev. 6/15//2007)

Image 11

Contents Rotary Cutter Introduction Table of Contents DS1260 DSO1260 DS1440 DS1260Q DSO1260Q DS1440Q SpecificationsGeneral Information Free Mower Safety Video Training Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters-EnglishPreparation Safety RulesTraining Transportation OperationKeep children and bystanders away from stor- age area MaintenanceStorage Follow manual instructions for storage Be Careful Safety & Instructional Decals6a PN RPM -OR 6b PN 1000 RPM Keep Away15a PN 540 RPM 15b PN 1000 RPM Raised Cutter can Drop and CrushConnect Cutter to Tractor PULL-TYPE OperationTractor Stability Connect Cutter to Tractor Mounted & SEMI-MOUNTED Shorten Driveline Driveline Adjustment Mounted & SEMI-MOUNTEDCategory 3 Standard Hitch Category 2 & 3 Quick HitchesMounted & Semi-Mounted Units Cutting Height AdjustmentDriveline Interference Check Pull-Type UnitsBlade Selection Attitude Adjustment PULL-TYPEDriveline Adjustment PULL-TYPE Wheel SpacingTransporting Cutter OperationMowing Tips Owners Responsibility PRE-OPERATION Check ListGearbox Lubrication Owner ServiceBlocking Method LubricationJackstand Placement and Lubrication Points Sharpening Blades Installing BladesBlade Servicing Removing Blades FigureShielding Repair Slip Clutch AdjustmentRepairing Rubber Shielding Repairing Optional Chain ShieldingUsed Aircraft Tires Figure Flexible Coupler Rubber Disk ReplacementServicing Tires Safely Periodically or Before Extended Storage CleaningAfter Each Use Problem Possible Cause Solution TroubleshootingMAN0571 rev /15//2007 Seal Installation Dealer ServiceGearbox Maintenance Seal ReplacementAssemble Gearbox Horizontal Shaft Seal Repair FigureSpindle Gearbox Repair Figure Remove Gearbox From Cutter Disassemble GearboxSpindle Gearbox Assembly Reinstall GearboxDisassemble Gearbox Figure Splitter Gearbox Repair Figure Remove Gearbox from CutterAssemble Gearbox Figure Side Drive ServiceCrossbar Removal CrossbarCrossbar Timing Crossbar InstallationUniversal Joint Repair Joint DisassemblyInstall Cups Joint AssemblyDS1260 & DS1440 PULL-TYPE Cutter Assembly InstructionsDealer SET-UP Instructions DS1260 & DS1440 Pull-Type Cutter Assembly Rear Half Install SMV EmblemDS1260 & DS1440 Pull-Type Cutter Assembly Front Half Install 3-Joint Driveline Figure Front Half Figure Install TongueInstall CV Driveline Optional DS1260 & DS1440 CV Drive Installation Install Driveline Install A-Frame MountedInstall Tailwheel Arms Install Hydraulic HosesDS1260 & DS1440 Mounted Cutter Assembly See Figure Install SMV Emblem Semi-MountedDSO1260 Cutter Figure Install Hitch MechanismDSO1260 Cutter Assembly Rubber Shielding Figure Install Chain or Rubber ShieldingDS1260 & DS1440 ALL Models Fill GearboxesDS1440 DS1260DS1260 DS1440 Optional Chain Shielding InstallationDelivery Check List Dealer Check ListsPRE-DELIVERY Check List Parts Index DS1260 / DS1440 Main Frame Assembly Part QTY Description Tongue S/N 1081498 & after DS1260 / DS1440 PULL-TYPE Assembly Front HalfDS1260 / DS1440 PULL-TYPE Assembly Rear Half DS1260 / DS1440 PULL-TYPE Optional CV Mounting Assembly Tailwheel see DS1260 / DS1440 Mounted Cutter AssemblyDS1260 / DS1440 SEMI-MOUNTED Cutter Assembly Drive 540 RPM see page 74 -or DSO1260 AssemblyGear 19 are Reversed on RPM Gearbox DS1260 / DS1440 / DSO1260 Splitter Gearbox AssemblyDS1260 / DS1440 / DSO1260 Spindle Gearbox Assembly DS1260 / DS1440 / DSO1260 Flexible Coupler DS1260 / DS1260Q & DS1440 / DS1440Q Front Equal Angle Drive Assembly PULL-TYPERear Equal Angle Drive Assembly PULL-TYPE See page 69 for Star Profile Parts See page 67 or 68 for Spline Profile RPM Front CV Drive Assembly Walterscheid Star ProfileRPM 1-3/8 21-SPLINED RPM 1-3/4 20-SPLINED RPM 1-3/8 21-SPLINED RPM 1-3/4 20-SPLINE See page 70 or 71 for Weasler Profile RPM Front CV Drive Assembly Walterscheid Spline ProfileRear FIXED-LENGTH Drive for Constant Velocity Drive DS1260 Q / DS1440 Q / DSO1260 Q Slip Clutch Drive Assembly MountedREF Part QTY Description Wheel & Tire AssemblyMDS1260 / MDS1440 Mounted Tailwheel Assembly 00 x 9 Tire DS1260/DSO1260 DS1440 DS1260 / DS1440 Belt Shielding StandardDS1260 / DS1440 Chain Shielding Optional 2 x 8 Stroke Hydraulic Cylinder Optional Crossbar Puller Optional Hydraulic Cylinder Stroke Control KIT OptionalMetric Series Torque Chart Bolt Torque ChartSAE Series Torque Chart Abbreviations Bolt Size ChartIndex AssemblyWarranty South Illinois Route Post Office Box Oregon, Illinois