Woods Equipment BW240HDQ manual 1000 RPM

Page 12
18865--C
15922-C

SAFETY & INSTRUCTIONAL DECALS

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

WARNING

DO NOT EXCEED PTO SPEED OF

1000 RPM

PTO speeds higher than 1000 RPM can cause equipment failure and personal injury.

WARNING￿￿￿￿￿￿ ￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿540￿￿￿￿￿￿￿￿￿￿RPM￿￿￿￿!￿￿￿￿￿"￿￿#￿￿￿￿￿$

18866-D

5 - PN 15922

OR

6 - PN 18866

7 - PN 15503

DANGER

ROTATING BLADES AND

THROWN OBJECTS

Do not put hands or feet under or into mower when engine is running.

Before mowing, clear area of objects that may be thrown by blade.

Keep bystanders away.

Keep guards in place and in good condition.

BLADE CONTACT OR THROWN OBJECTS CAN CAUSE SERIOUS INJURY OR DEATH.

15503-C

8 - PN 18864

DANGER

ROTATING DRIVELINE

CONTACT CAN CAUSE DEATH

KEEP AWAY!

DO NOT OPERATE WITHOUT -

All driveline guards, tractor and equipment shields in place

Drivelines securely attached at both ends

Driveline guards that turn freely on

 

driveline

18864-C

 

9 - PN 18865

WARNING

FALLING OFF CAN RESULT IN BEING RUN OVER.

„Tractor must be equipped with ROPS (or ROPS CAB) and seat belt. Keep foldable ROPS systems in “locked up” position at all times.

„Buckle Up! Keep seat belt securely fastened.

„Allow no riders.

RAISED EQUIPMENT CAN DROP AND CRUSH.

„Before working underneath, follow all instructions and safety rules in operator’s manual and securely block up all corners of equipment with jack stands.

„Securely blocking prevents equipment dropping from hydraulic leak- down, hydraulic system failures or mechanical component failures.

FALLING OFF OR FAILING TO BLOCK SECURELY CAN RESULT IN SERIOUS INJURY OR DEATH.

11 - PN 19924

19924-B

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿WARNING￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

Check for leaks with cardboard; never use hand.

Before loosening fittings: lower load, release pressure, and

￿be sure oil is cool.

Consult physician immediately if skin penetration occurs.

12 Safety

MAN0763 (10/10/2008)

 

 

Image 12
Contents Batwing Introduction To the DealerTable of Contents Specifications General InformationBW240HD / BW240HDQ Free Mower Safety Video SafetyTraining Package for Rotary Mowers/Cutters-English Training Package for Rotary Mowers/Cutters-English/SpanishSafety Rules InstallationTraining PreparationTransportation OperationMaintenance Storage Safety & Instructional Decals Be CarefulPN 1006348 Located on Wheel Rims 1000 RPM Safety Connecting Cutter to Tractor OperationOperation Cutting Height Adjustment Hydraulic ConnectionInterference Check CV Driveline Turning LimitsTractor Operation Cutter OperationMowing Tips Cutting Height Normal Mowing WingsShredding TransportingLock-Up Wing Lock-UpPRE-OPERATION Check List Center Section Lock-UpOwner Service Owner ServiceBlocking Method Lubrication Gearbox LubricationDriveline Lubrication Blade Installation Figure Seasonal LubricationBlades Blade Removal FigureSlip Clutch Adjustment Figure Blade SharpeningService Tires Safely CleaningShielding Repair Troubleshooting TroubleshootingDealer Service Dealer ServiceGearbox Maintenance Seal Replacement FigureDisassembly Figure Gearbox RepairRemoval from Cutter Figure Reinstallation GearboxDisassembly AssemblySplitter Gearbox Repair Figure Removal from Cutter Gearbox Installation Gearbox InspectionCrossbar Removal Crossbar RemovalCrossbar Installation Joint DisassemblyUniversal Joint Repair Joint Assembly Assembly Assembly InstructionsCenter Section Assembly Dealer SET-UP InstructionsInstall Height Adjustment Cylinder Install SMV EmblemInstall Spring Wheel Arms Install TongueInstall 3-Joint Drive 540 RPM Only Joint Drive InstallationInstall CV Drive Optional Install Wing Cylinder & Transport lockWing Assembly Install WingInstall Wing Wheel Yoke Wing Cylinder & Wing Transport Lock InstallationInstall Wing Wheel Yoke Adjustment Link Install Wing DrivelineFill Gearboxes Install Tandem Wheel Assembly Center Install Tandem Wheel Assembly WingOptional Equipment Install Chain or Belt Shielding Chain Shielding Installation Center SectionBelt Shielding Installation Center Section Winch Kit Installation Belt Shielding Installation Right WingDealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListParts BW240HD, BW240HDQMain Frame Assembly Front Section Part Main Frame Assembly Rear Section 1027070 Center wheel yoke 57050 Access hole cover 10475 Right Wing Shown REF Part QTY Description Wing & Center Gearbox Assembly 540 RPM 1000 RPM Splitter Gearbox Assembly Part QTY DescriptionCenter Deck Drive Assembly Front 3-JOINT Drive Assembly Equal Angle 540 only Rear 3-JOINT Drive Assembly Equal Angle RPM Front CV Drive RPM 1-3/8 21-Splined RPM 1-3/4 20-SplinedWing Drive Assembly Bolt Wheel & Tire Assembly Rubber Shielding Center Section Standard Rubber Shielding Wing Standard Chain 7 link 5496 Chain Shielding Wing Optional Single ROW Double ROW Tandem Axle Wheel Yoke Optional Hydraulic Cylinders Crossbar Puller Optional Hydraulic Cylinder Stroke Control KITWinch KIT Optional Winch Kit OperationBW240HD Shredder KIT Optional This KIT does not FIT BW240Parts Bolt Torque Chart SAE Series Torque ChartAppendix Metric SeriesBolt Size Chart AbbreviationsIndex IndexWarranty Warranty