Woods Equipment BW240HDQ manual Optional Equipment, Install Tandem Wheel Assembly Center

Page 40

OPTIONAL EQUIPMENT

Install Tandem Wheel Assembly (Center)

1.Slide spring wheel arm assembly (1) over right side of center wheel yoke tube and secure into position using four cap screw (22) and flanged lock nut (23). Repeat step to install spring wheel arm assembly on left side of center wheel yoke tube.

2.Place tandem wheel bracket (16) around lower lower spring arm (13) and insert flange pin (17). Secure flange pin to tandem wheel bracket using cap screw (18) and flat washer (19).

3.Insert wheel hubs (15) into both sides of tandem wheel bracket (16) and align holes.

4.Secure into position using cap screws (20) and flanged lock nuts (21).

5.Attach wheel to hub using five lug nuts. Install the chamfered side of the lug nut toward the inside for steel rim for pneumatic tires and rims. Tighten to 75 lbs-ft. Check that tire air pressure is a maximum of 40 psi.

NOTE: Install the flat side of the nut toward the inside for solid tires and aircraft tires (shown).

Install Tandem Wheel Assembly (Wing)

1.Attach wing wheel yoke (2) to the wing using pivot pins (31). See Figure 30 for pin and hardware installation. Make sure pin flange is on the underside of the deck.

2.Secure pivot pins to deck using carriage bolts (67) and flange lock nuts (53). See Figure 30 for pin and hardware installation. Carriage bolts are on the outside, lock nuts on the underside.

3.Place tandem wheel bracket (16) around lower lower spring arm (3) and insert flange pin (17). Secure flange pin to tandem wheel bracket using cap screw (18) and flat washer (19).

4.Insert wheel hubs (15) into both sides of tandem wheel bracket (16) and align holes. Secure using cap screws (20) and flanged lock nuts (21).

5.Attach wheel to hub using five lug nuts. Install the chamfered side of the lug nut toward the inside for steel rim for pneumatic tires and rims. Tighten to 75 lbs-ft. Set tire pressure to a maximum of 40 psi.

6.Install the flat side of the nut toward the inside for solid tires and aircraft tires (shown).

1. Wheel yoke arm

2. Wing wheel yoke arm, right

3. Spring arm, wing right

13. Lower spring arm

15. Wheel and hub

16. Tandem bracket

17. Flange pin, 1.56 x 11.06

18. 1/2 NC x 1-1/4 HHCS GR5

19. 1/2 Flat washer

20. 1/2 NC x 3 HHCS GR5

21. 1/2 NC Flange lock nut

22. 3/4 NC x 6 HHCS GR5

23. 3/4 NC Lock nut

Figure 33. Tandem Wheel Assembly Installation

40Assembly

(Rev. 9/4/2009) MAN0763 (10/10/2008)

Image 40
Contents Batwing Introduction To the DealerTable of Contents General Information SpecificationsBW240HD / BW240HDQ Free Mower Safety Video SafetyTraining Package for Rotary Mowers/Cutters-English Training Package for Rotary Mowers/Cutters-English/SpanishSafety Rules InstallationTraining PreparationTransportation OperationMaintenance Storage Be Careful Safety & Instructional DecalsPN 1006348 Located on Wheel Rims 1000 RPM Safety Operation Connecting Cutter to TractorOperation Cutting Height Adjustment Hydraulic ConnectionInterference Check CV Driveline Turning LimitsTractor Operation Cutter OperationMowing Tips Cutting Height Normal Mowing WingsShredding TransportingLock-Up Wing Lock-UpPRE-OPERATION Check List Center Section Lock-UpOwner Service Owner ServiceBlocking Method Gearbox Lubrication LubricationDriveline Lubrication Blade Installation Figure Seasonal LubricationBlades Blade Removal FigureSlip Clutch Adjustment Figure Blade SharpeningCleaning Service Tires SafelyShielding Repair Troubleshooting TroubleshootingDealer Service Dealer ServiceGearbox Maintenance Seal Replacement FigureGearbox Repair Disassembly FigureRemoval from Cutter Figure Reinstallation GearboxAssembly DisassemblySplitter Gearbox Repair Figure Removal from Cutter Gearbox Installation Gearbox InspectionCrossbar Removal Crossbar RemovalJoint Disassembly Crossbar InstallationUniversal Joint Repair Joint Assembly Assembly Assembly InstructionsCenter Section Assembly Dealer SET-UP InstructionsInstall Height Adjustment Cylinder Install SMV EmblemInstall Spring Wheel Arms Install TongueInstall 3-Joint Drive 540 RPM Only Joint Drive InstallationInstall CV Drive Optional Install Wing Cylinder & Transport lockWing Assembly Install WingInstall Wing Wheel Yoke Wing Cylinder & Wing Transport Lock InstallationInstall Wing Driveline Install Wing Wheel Yoke Adjustment LinkFill Gearboxes Install Tandem Wheel Assembly Wing Install Tandem Wheel Assembly CenterOptional Equipment Install Chain or Belt Shielding Chain Shielding Installation Center SectionBelt Shielding Installation Center Section Winch Kit Installation Belt Shielding Installation Right WingDealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListParts BW240HD, BW240HDQMain Frame Assembly Front Section Part Main Frame Assembly Rear Section 1027070 Center wheel yoke 57050 Access hole cover 10475 Right Wing Shown REF Part QTY Description Wing & Center Gearbox Assembly 540 RPM 1000 RPM Splitter Gearbox Assembly Part QTY DescriptionCenter Deck Drive Assembly Front 3-JOINT Drive Assembly Equal Angle 540 only Rear 3-JOINT Drive Assembly Equal Angle RPM Front CV Drive RPM 1-3/8 21-Splined RPM 1-3/4 20-SplinedWing Drive Assembly Bolt Wheel & Tire Assembly Rubber Shielding Center Section Standard Rubber Shielding Wing Standard Chain 7 link 5496 Chain Shielding Wing Optional Single ROW Double ROW Tandem Axle Wheel Yoke Optional Hydraulic Cylinders Crossbar Puller Optional Hydraulic Cylinder Stroke Control KITWinch KIT Optional Winch Kit OperationBW240HD Shredder KIT Optional This KIT does not FIT BW240Parts Bolt Torque Chart SAE Series Torque ChartAppendix Metric SeriesBolt Size Chart AbbreviationsIndex IndexWarranty Warranty