Woods Equipment BW240HDQ manual Install 3-Joint Drive 540 RPM Only, Joint Drive Installation

Page 36

Install 3-Joint Drive (540 RPM Only)

Before installing cutter input driveline to gearbox, check the tag wired to the driveline and the tag wired to the input shaft of gearbox. Ensure the tag rpm speeds match the rpm speed decal on front of cutter. After con- firming all speeds match, remove and discard tags and then complete driveline assembly.

1.Attach H-frame (24) to tongue with cap screw (44), sleeves (46), cup washers (45), and nut (47).

4.Secure with bolt and nut supplied with drive.

5.Secure driveline carrier bearing to H-frame with cap screw (48), washer (51), sleeves (54) and a flanged lock nut (53).

NOTE: When cutting height is established, adjust the 3-joint H-frame bearing height so that the front driveline is parallel to the ground.

6.Attach front driveline (26) to rear driveline (27) and tighten clamp bolt and nut.

2.Coat splined end of gearbox input shaft with grease.

3.Align hole in drive yoke with groove on gearbox input shaft and slide drive (27) onto shaft.

7.Attach shield (17) to driveline carrier bearing with two cap screws (55) and lock washers (58).

8.Attach spacer (52) and hydraulic hose holder (25) to top hole of H-frame using cap screw (48) and flanged lock nut (53).

17. Carrier bearing shield

22. Tongue

24.H-frame

25.Hydraulic hose holder

26.Front half, 3-joint drive

27.Rear half, Telescoping driveshaft

44.5/8" NC x 7" HHCS GR5

45.5/8" x 1-3/4" x 14 ga Cup washer

46.5/8" x 1" x 9/16" Sleeve, HT

47.5/8" NC Lock nut

48.1/2" NC x 6-1/2" HHCS GR5

51.1/2" Flat washer

52.1/2" x 4.56" Spacer, pipe schedule 40

53.1/2" NC Flanged lock nut

54.Sleeve, .50" x 1.00" x 1.031"

55.3/8" NC x 1" HHCS GR5

56.3/8" Lock washer

Figure 26. 3-Joint Drive Installation

36 Assembly

MAN0763 (10/10/2008)

 

 

Image 36
Contents Batwing Introduction To the DealerTable of Contents Specifications General InformationBW240HD / BW240HDQ Free Mower Safety Video SafetyTraining Package for Rotary Mowers/Cutters-English Training Package for Rotary Mowers/Cutters-English/SpanishSafety Rules InstallationTraining PreparationTransportation OperationMaintenance Storage Safety & Instructional Decals Be CarefulPN 1006348 Located on Wheel Rims 1000 RPM Safety Connecting Cutter to Tractor OperationOperation Cutting Height Adjustment Hydraulic ConnectionInterference Check CV Driveline Turning LimitsTractor Operation Cutter OperationMowing Tips Cutting Height Normal Mowing WingsShredding TransportingLock-Up Wing Lock-UpPRE-OPERATION Check List Center Section Lock-UpOwner Service Owner ServiceBlocking Method Lubrication Gearbox LubricationDriveline Lubrication Blade Installation Figure Seasonal LubricationBlades Blade Removal FigureSlip Clutch Adjustment Figure Blade SharpeningService Tires Safely CleaningShielding Repair Troubleshooting TroubleshootingDealer Service Dealer ServiceGearbox Maintenance Seal Replacement FigureDisassembly Figure Gearbox RepairRemoval from Cutter Figure Reinstallation GearboxDisassembly AssemblySplitter Gearbox Repair Figure Removal from Cutter Gearbox Installation Gearbox InspectionCrossbar Removal Crossbar RemovalCrossbar Installation Joint DisassemblyUniversal Joint Repair Joint Assembly Assembly Assembly InstructionsCenter Section Assembly Dealer SET-UP InstructionsInstall Height Adjustment Cylinder Install SMV EmblemInstall Spring Wheel Arms Install TongueInstall 3-Joint Drive 540 RPM Only Joint Drive InstallationInstall CV Drive Optional Install Wing Cylinder & Transport lockWing Assembly Install WingInstall Wing Wheel Yoke Wing Cylinder & Wing Transport Lock InstallationInstall Wing Wheel Yoke Adjustment Link Install Wing DrivelineFill Gearboxes Install Tandem Wheel Assembly Center Install Tandem Wheel Assembly WingOptional Equipment Install Chain or Belt Shielding Chain Shielding Installation Center SectionBelt Shielding Installation Center Section Winch Kit Installation Belt Shielding Installation Right WingDealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListParts BW240HD, BW240HDQMain Frame Assembly Front Section Part Main Frame Assembly Rear Section 1027070 Center wheel yoke 57050 Access hole cover 10475 Right Wing Shown REF Part QTY Description Wing & Center Gearbox Assembly 540 RPM 1000 RPM Splitter Gearbox Assembly Part QTY DescriptionCenter Deck Drive Assembly Front 3-JOINT Drive Assembly Equal Angle 540 only Rear 3-JOINT Drive Assembly Equal Angle RPM Front CV Drive RPM 1-3/8 21-Splined RPM 1-3/4 20-SplinedWing Drive Assembly Bolt Wheel & Tire Assembly Rubber Shielding Center Section Standard Rubber Shielding Wing Standard Chain 7 link 5496 Chain Shielding Wing Optional Single ROW Double ROW Tandem Axle Wheel Yoke Optional Hydraulic Cylinders Crossbar Puller Optional Hydraulic Cylinder Stroke Control KITWinch KIT Optional Winch Kit OperationBW240HD Shredder KIT Optional This KIT does not FIT BW240Parts Bolt Torque Chart SAE Series Torque ChartAppendix Metric SeriesBolt Size Chart AbbreviationsIndex IndexWarranty Warranty