Woods Equipment BW240HDQ manual Dealer Check Lists, PRE-DELIVERY Check List, Delivery Check List

Page 44

DEALER CHECK LISTS

PRE-DELIVERY CHECK LIST

(DEALER’S RESPONSIBILITY)

Inspect the equipment thoroughly after assembly to ensure it is set up properly before delivering it to the customer.

The following check lists are a reminder of points to inspect. Check off each item as it is found satisfactory or after proper adjustment is made.

NOTICE

Gearboxes are not filled at the factory. Prior to delivery, make sure each gearbox is filled between lowest ring and end of dipstick with 80 or 90W API GL-4 or GL-5 gear lube.

___ Check that all safety decals are installed and in good condition. Replace if damaged.

___ Check that shields and guards are properly installed and in good condition. Replace if dam-

 

aged.

___

Check all bolts to be sure they are properly

 

torqued.

___

Check wheel bolts for proper torque.

___

Check that all cotter pins and safety pins are

 

properly installed. Replace if damaged.

___

Check that blades have been properly installed.

___

Check and grease all lubrication points as identi-

 

fied in lubrication information on page 20.

___

Check the level of gearbox fluids before delivery.

 

Service, if required, as specified in the lubrication

 

information on page 20.

DELIVERY CHECK LIST

(DEALER’S RESPONSIBILITY)

___ Show customer how to make adjustments and select proper PTO speed.

___ Show customer how to make sure driveline is properly installed and that spring-activated lock- ing pin or collar slides freely and is seated in groove on tractor PTO shaft.

___

Show customer how to determine the turning lim-

 

its of the CV PTO driveline.

___

Show customer the safe, proper procedures to be

 

used when mounting, dismounting, and storing

 

equipment.

___

Make customer aware of optional equipment

 

available so that customer can make proper

 

choices as required.

___

Instruct customer how to lubricate and explain

 

importance of lubrication.

___

Point out the safety decals. Explain their meaning

 

and the need to keep them in place and in good

 

condition. Emphasize the increased safety haz-

 

ards when instructions are not followed.

___

Explain to customer that when transporting the

 

cutter, the wing and center sections should be

 

raised and their respective transport bars

 

installed and pinned in place.

___

Present Operator's Manual and request that cus-

 

tomer and all operators read it before operating

 

equipment. Point out the manual safety rules,

 

explain their meanings and emphasize the

 

increased safety hazards that exist when safety

 

rules are not followed.

___

Explain to customer the potential crushing haz-

 

ards of going underneath raised equipment.

 

Instruct that before going underneath to discon-

 

nect the driveline, securely block up all corners

 

with jack stands and to follow all instructions in

 

the BLOCKING METHOD, page 19 of the opera-

 

tor’s manual. Explain that blocking up prevents

 

equipment dropping from hydraulic leak down,

 

hydraulic system failures or mechanical compo-

 

nent failures.

___

Point out all guards and shields. Explain their

 

importance and the safety hazards that exist

 

when not kept in place and in good condition.

___

Explain to customer that when towing on a public

 

road to comply with all state and local light-

 

ing/marking laws and to use a safety tow chain.

44 Dealer Check Lists

MAN0725 (10/3/2008)

 

Image 44
Contents Batwing Introduction To the DealerTable of Contents BW240HD / BW240HDQ SpecificationsGeneral Information Free Mower Safety Video SafetyTraining Package for Rotary Mowers/Cutters-English Training Package for Rotary Mowers/Cutters-English/SpanishSafety Rules InstallationTraining PreparationTransportation OperationMaintenance Storage PN 1006348 Located on Wheel Rims Safety & Instructional DecalsBe Careful 1000 RPM Safety Operation Connecting Cutter to TractorOperation Cutting Height Adjustment Hydraulic ConnectionInterference Check CV Driveline Turning LimitsTractor Operation Cutter OperationMowing Tips Cutting Height Normal Mowing WingsShredding TransportingLock-Up Wing Lock-UpPRE-OPERATION Check List Center Section Lock-UpBlocking Method Owner ServiceOwner Service Driveline Lubrication LubricationGearbox Lubrication Blade Installation Figure Seasonal LubricationBlades Blade Removal FigureSlip Clutch Adjustment Figure Blade SharpeningShielding Repair Service Tires SafelyCleaning Troubleshooting TroubleshootingDealer Service Dealer ServiceGearbox Maintenance Seal Replacement FigureRemoval from Cutter Figure Disassembly FigureGearbox Repair Reinstallation GearboxSplitter Gearbox Repair Figure Removal from Cutter DisassemblyAssembly Gearbox Installation Gearbox InspectionCrossbar Removal Crossbar RemovalUniversal Joint Repair Crossbar InstallationJoint Disassembly Joint Assembly Assembly Assembly InstructionsCenter Section Assembly Dealer SET-UP InstructionsInstall Height Adjustment Cylinder Install SMV EmblemInstall Spring Wheel Arms Install TongueInstall 3-Joint Drive 540 RPM Only Joint Drive InstallationInstall CV Drive Optional Install Wing Cylinder & Transport lockWing Assembly Install WingInstall Wing Wheel Yoke Wing Cylinder & Wing Transport Lock InstallationFill Gearboxes Install Wing Wheel Yoke Adjustment LinkInstall Wing Driveline Optional Equipment Install Tandem Wheel Assembly CenterInstall Tandem Wheel Assembly Wing Install Chain or Belt Shielding Chain Shielding Installation Center SectionBelt Shielding Installation Center Section Winch Kit Installation Belt Shielding Installation Right WingDealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListParts BW240HD, BW240HDQMain Frame Assembly Front Section Part Main Frame Assembly Rear Section 1027070 Center wheel yoke 57050 Access hole cover 10475 Right Wing Shown REF Part QTY Description Wing & Center Gearbox Assembly 540 RPM 1000 RPM Splitter Gearbox Assembly Part QTY DescriptionCenter Deck Drive Assembly Front 3-JOINT Drive Assembly Equal Angle 540 only Rear 3-JOINT Drive Assembly Equal Angle RPM Front CV Drive RPM 1-3/8 21-Splined RPM 1-3/4 20-SplinedWing Drive Assembly Bolt Wheel & Tire Assembly Rubber Shielding Center Section Standard Rubber Shielding Wing Standard Chain 7 link 5496 Chain Shielding Wing Optional Single ROW Double ROW Tandem Axle Wheel Yoke Optional Hydraulic Cylinders Crossbar Puller Optional Hydraulic Cylinder Stroke Control KITWinch KIT Optional Winch Kit OperationBW240HD Shredder KIT Optional This KIT does not FIT BW240Parts Bolt Torque Chart SAE Series Torque ChartAppendix Metric SeriesBolt Size Chart AbbreviationsIndex IndexWarranty Warranty