Sterling Plumbing 6103 Series manual Construire le cadrage, Construct the Framing

Page 10

Construct the Framing (cont.)

Studs must be positioned roughly as shown in the ″Roughing-In″ section to properly fasten the attachment clips or the bath flange. Other stud locations are optional except for those which must meet the load-bearing requirements of local building codes. Studs must also allow for the installation of plumbing fittings and any shower door. Locate the shower door studs as required by the shower door manufacturer.

For Bath with Apron Flanges

If apron flanges are in place on the apron, ensure that the outer stud is positioned for the apron flanges at 31-1/4″ (79.4 cm) from the back wall. The outer edge of the stud should align with the edge of the apron flange.

If the apron flanges are not going to be used or are broken, install three evenly distributed 2x4 blocks just behind the apron location. The blocks will prevent the apron from being damaged and may be used to secure the apron behind the baseboard. Measure the bath for the required clearance behind the apron and for the location of the blocks.

For Bath with Wall Surrounds

NOTE: If the wall surrounds will be installed to a masonry wall, make provisions for plumbing connections. For the plumbing end wall, construct a separate frame wall a minimum of 6″ (15.2 cm) from the masonry wall. For the remaining walls, use 2x2 furring strips to provide stud locations.

Ensure that the outer stud is positioned with the vertical wall flanges 31-1/4″ (79.4 cm) from the back wall. The outer edge of the stud should align with the edge of the wall flange.

IMPORTANT! Accessories that require backing or support are not recommended for this installation. Installing these accessories could void the warranty.

Ensure fiber or other soft insulation does not drop down into the water channel. Cover or seal any loose material. Failure to do so may cause wicking of water from the water channel into the insulation which may induce mold, leakage, or mildew. Ensure the channels are free of debris after installation.

For Above-the-Floor Drain Baths

Ensure the drain piping can pass through the wall and that the load bearing requirements of the wall are satisfied. Modify the framing or raise the subfloor as required to obtain clearance.

For All Installations

Construct 2x4 stud framing for your particular installation according to the ″Roughing-In″ section.

Ensure that the framing for each stud is plumb and square within 1/8″ (3 mm). Shimming will be required if tolerances are not met.

If possible, construct an access panel in the plumbing end wall to simplify future maintenance of all plumbing connections.

Construire le cadrage

REMARQUE: Se référer à la section ″Raccordement″ pour les dimensions.

Provisions cadrage

AVERTISSEMENT: Risque d’endommagent du produit et de la propriété. La baignoire doit être supportée par le plancher. Les murs avoisinants ne sont pas désignés pour maintenir la baignoire en place et ne sont pas conçus pour un

supportde charge. Les clips ou clous pour toiture doivent être utilisés pour éviter un mouvement latéral de la baignoire.

La baignoire avec bandeau doit être fixée aux montants sur trois côtés.

1064907-2-A

10

Sterling

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Series/Séries 6103/Serie 1064907-2-A Important Information Plus Tools and MaterialsMás Gracias por elegir los productos de Sterling Thank You For Choosing SterlingMerci d’avoir choisi Sterling Before You BeginAvant de commencer Before You BeginAntes de comenzar Avant de commencerAntes de comenzar Roughing-In RaccordementRaccordement Diagrama de instalaciónConstruct the Framing Framing ProvisionsConstruire le cadrage Construct the FramingConstruya la estructura de postes de madera Construire le cadragePara bañera con paredes circundantes Construya la estructura de postes de maderaPara bañeras con rebordes del faldón Para bañeras con desagüe arriba del nivel del pisoLevel the Subfloor Prepare the SubfloorPréparer le plancher Niveler le plancherPréparer le plancher Prepare el subpisoNivele el subpiso Installer la plomberie de raccordement Install the Rough PlumbingSeries 6103/Séries 6103/Serie Instale el tendido de tuberías Install a Mortar Cement Bed Optional Position the BathPositionner la baignoire Installer un lit de mortier OptionnelPosition the Bath Coloque la bañera Instale una capa de cemento mortero opcionalSecure the Apron Secure the BathNail Attach the Bath to the StudsSécuriser le bandeau Sécuriser la baignoireSecure the Bath Attacher la baignoire aux montantsFije la bañera a los postes de madera Fije la bañeraFije el faldón Para fijar con clipsPre-Fit the Wall Surrounds IMPORTANT! Install the back wall firstIMPORTANT! Installer d’abord le mur arrière Prémunir les murs avoisinantsPrémunir les murs avoisinants Ajuste inicial de las paredes circundantes¡IMPORTANTE! Instale primero la pared posterior For Baths with Wall Surrounds Only Prepare the Wall SurroundsPréparer les murs avoisinants Pour les baignoires avec des murs avoisinants uniquementPréparer les murs avoisinants Accessoires optionnelsPrepare las paredes circundantes Sólo para bañeras con paredes circundantesPrepare las paredes circundantes Apply Silicone Sealant Appliquer du mastic à la siliconeAplique sellador de silicona Appliquer du mastic à la siliconeSecure the Wall Surrounds NecesarioFije las paredes circundantes Sécuriser les murs avoisinantsSecure the Wall Surrounds Complete the Installation Fije las paredes circundantesCompléter l’installation Termine la instalaciónSymptômes Causes probables Action recommandée TroubleshootingSymptoms Probable Causes Recommended Action DépannageDépannage Procedimiento para resolver problemasCare and Cleaning Síntomas Causas probables Acción recomendadaInstructions d’entretien et de nettoyage Care and CleaningCuidado y limpieza Cuidado y limpieza WarrantyGarantie Years Limited Consumer/3 Years Limited CommercialGarantía Garantie1064907-2-A Phone 1-888-STERLING Mexico

6103 Series specifications

The Sterling Plumbing 6103 Series is a remarkable line of bathroom fixtures that combines modern design with practical functionality. Renowned for its durability and aesthetic appeal, this series has set a new standard in the industry for mid-range plumbing products.

One of the standout features of the 6103 Series is its high-quality construction. Made with robust materials, the fixtures are engineered to withstand daily use while maintaining their appearance over time. The chrome finish not only enhances the aesthetic appeal with a sleek look but also provides resistance against corrosion and tarnishing. This ensures that your bathroom remains stylish and functional for longer.

The 6103 Series is designed with user-friendliness in mind. The faucets and showerheads are equipped with easy-to-use handles that allow for precise temperature and water flow control. This smart design contributes to a more enjoyable showering and washing experience. Additionally, the installation process is straightforward, making it accessible for both homeowners and professional plumbers alike.

Technologically, the 6103 Series incorporates water-saving innovations that help reduce consumption without sacrificing performance. This is especially appealing for environmentally conscious consumers looking to minimize their water bills. The series often features aerated flow technology, which mixes air with water to create a fuller water stream while reducing overall water use by up to 30%.

The design elements of the Sterling 6103 Series reflect contemporary trends with clean lines and sophisticated profiles, making it a versatile choice for various bathroom styles, from modern to classic. The thoughtful design extends to the ergonomics of each piece, ensuring that they not only look good but feel good to use.

Another characteristic of the 6103 Series is its comprehensive warranty, providing added peace of mind for customers. Sterling stands behind its products, assuring buyers that they are investing in reliable plumbing fixtures.

In summary, the Sterling Plumbing 6103 Series is a blend of durability, eco-friendliness, and contemporary design. Its user-focused features, coupled with advanced technologies, make it an exceptional choice for anyone looking to upgrade their bathroom fixtures without breaking the bank. Whether it’s for a personal residence or a renovation project, the 6103 Series is sure to elevate the overall functionality and look of any bathroom space.
Top Page Image Contents