Sterling Plumbing 6103 Series manual Secure the Wall Surrounds, Necesario

Page 30

Stud/Montant/Poste de madera

Shim if necessary.

 

Wall Flange

Caler si nécessaire.

Utilice cuñas de ser

Bride du mur

Reborde de la pared

necesario.

Bath Flange

Bride de la baignoire

Reborde de la bañera

Wall Surround Mur avoisinant Paredes circundantes

1/32" (1 mm)

Bath

Baignoire

Bañera

Roofing Nail or Flathead Screw Clous pour toiture ou vis à tête plate Clavo de techar o tornillo de cabeza plana

Secure the Wall Surrounds

Remove the temporary roofing nail from the back wall.

CAUTION: Risk of property damage. Wall surrounds must rest within 1/32″ (1 mm) (the thickness of a credit card) from the bath rim to ensure proper water

management and to prevent leakage.

Ensure that the wall surrounds are properly secured and seated on the bath. The front edges of the end walls must be flush with the front edge of the bath. If a gap exists, pull the end walls slightly forward.

CAUTION: Risk of product or property damage. If using non-tapered flathead screws rather than roofing nails, do not overtighten the screws. Excessive

tightening can damage the wall flange.

Starting from the bottom of the end walls and working up, secure the end walls to the studs approximately every 12″ (30.5 cm). If roofing nails are used, nail through the dimples on the wall flanges. If using non-tapered flathead screws, drill through the dimples on the wall flanges. Do not overtighten the non-tapered flathead screws.

NOTE: Leave a 1/8″ (3 mm) gap between the edge of the wall surround and the finished wall material. When sealed, this gap will reduce the possibility of water seeping into the wall material.

Ensure fiber or other soft insulation does not drop down into the water channel. Cover or seal any loose material. Failure to do so may cause wicking of water from the water channel into the insulation which may induce mold, leakage, or mildew. Ensure the channels are free of debris after installation.

Secure the wall flanges across the top of the wall surrounds at every stud location. Add shims if necessary to bring the studs into contact with the bath flange.

1064907-2-A

30

Sterling

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Series/Séries 6103/Serie 1064907-2-A Important Information Tools and Materials PlusMás Gracias por elegir los productos de Sterling Thank You For Choosing SterlingMerci d’avoir choisi Sterling Before You BeginAvant de commencer Before You BeginAntes de comenzar Avant de commencerAntes de comenzar Roughing-In RaccordementRaccordement Diagrama de instalaciónConstruct the Framing Framing ProvisionsConstruire le cadrage Construct the FramingConstruya la estructura de postes de madera Construire le cadragePara bañera con paredes circundantes Construya la estructura de postes de maderaPara bañeras con rebordes del faldón Para bañeras con desagüe arriba del nivel del pisoLevel the Subfloor Prepare the SubfloorPréparer le plancher Niveler le plancherPrepare el subpiso Préparer le plancherNivele el subpiso Install the Rough Plumbing Installer la plomberie de raccordementSeries 6103/Séries 6103/Serie Instale el tendido de tuberías Install a Mortar Cement Bed Optional Position the BathInstaller un lit de mortier Optionnel Positionner la baignoirePosition the Bath Coloque la bañera Instale una capa de cemento mortero opcionalSecure the Apron Secure the BathNail Attach the Bath to the StudsSécuriser le bandeau Sécuriser la baignoireSecure the Bath Attacher la baignoire aux montantsFije la bañera a los postes de madera Fije la bañeraFije el faldón Para fijar con clipsPre-Fit the Wall Surrounds IMPORTANT! Install the back wall firstIMPORTANT! Installer d’abord le mur arrière Prémunir les murs avoisinantsAjuste inicial de las paredes circundantes Prémunir les murs avoisinants¡IMPORTANTE! Instale primero la pared posterior For Baths with Wall Surrounds Only Prepare the Wall SurroundsPréparer les murs avoisinants Pour les baignoires avec des murs avoisinants uniquementPréparer les murs avoisinants Accessoires optionnelsPrepare las paredes circundantes Sólo para bañeras con paredes circundantesPrepare las paredes circundantes Apply Silicone Sealant Appliquer du mastic à la siliconeAplique sellador de silicona Appliquer du mastic à la siliconeSecure the Wall Surrounds NecesarioSécuriser les murs avoisinants Fije las paredes circundantesSecure the Wall Surrounds Complete the Installation Fije las paredes circundantesCompléter l’installation Termine la instalaciónSymptômes Causes probables Action recommandée TroubleshootingSymptoms Probable Causes Recommended Action DépannageDépannage Procedimiento para resolver problemasCare and Cleaning Síntomas Causas probables Acción recomendadaCare and Cleaning Instructions d’entretien et de nettoyageCuidado y limpieza Cuidado y limpieza WarrantyGarantie Years Limited Consumer/3 Years Limited CommercialGarantía Garantie1064907-2-A Phone 1-888-STERLING Mexico

6103 Series specifications

The Sterling Plumbing 6103 Series is a remarkable line of bathroom fixtures that combines modern design with practical functionality. Renowned for its durability and aesthetic appeal, this series has set a new standard in the industry for mid-range plumbing products.

One of the standout features of the 6103 Series is its high-quality construction. Made with robust materials, the fixtures are engineered to withstand daily use while maintaining their appearance over time. The chrome finish not only enhances the aesthetic appeal with a sleek look but also provides resistance against corrosion and tarnishing. This ensures that your bathroom remains stylish and functional for longer.

The 6103 Series is designed with user-friendliness in mind. The faucets and showerheads are equipped with easy-to-use handles that allow for precise temperature and water flow control. This smart design contributes to a more enjoyable showering and washing experience. Additionally, the installation process is straightforward, making it accessible for both homeowners and professional plumbers alike.

Technologically, the 6103 Series incorporates water-saving innovations that help reduce consumption without sacrificing performance. This is especially appealing for environmentally conscious consumers looking to minimize their water bills. The series often features aerated flow technology, which mixes air with water to create a fuller water stream while reducing overall water use by up to 30%.

The design elements of the Sterling 6103 Series reflect contemporary trends with clean lines and sophisticated profiles, making it a versatile choice for various bathroom styles, from modern to classic. The thoughtful design extends to the ergonomics of each piece, ensuring that they not only look good but feel good to use.

Another characteristic of the 6103 Series is its comprehensive warranty, providing added peace of mind for customers. Sterling stands behind its products, assuring buyers that they are investing in reliable plumbing fixtures.

In summary, the Sterling Plumbing 6103 Series is a blend of durability, eco-friendliness, and contemporary design. Its user-focused features, coupled with advanced technologies, make it an exceptional choice for anyone looking to upgrade their bathroom fixtures without breaking the bank. Whether it’s for a personal residence or a renovation project, the 6103 Series is sure to elevate the overall functionality and look of any bathroom space.
Top Page Image Contents