Kohler 48VDC, 6VSG, 24VDC, 36VDC manual Service Views

Page 15

1.7 Service Views

2

1

3

8

9

10

7		4		11
6	5	4		12
6	5			16
			15	16
		14	15
		14
	13

21

17

kps_002.eps ADV-8060

	20	18
		19
1.	Exhaust air outlet	12.	Lifting hole
2.	Air cleaner	13.	Controller
3.	Oil fill	14.	Engine certification label
4.	Oil drain	15.	Load circuit breaker
5.	Oil drain valve	16.	Oil dipstick
6.	Oil filter	17.	Exhaust outlet
7.	Muffler	18.	Fuel inlet
8.	Alternator air inlet	19.	Electrical inlet
9.	Customer connection blocks (located behind panel)	20.	Battery cables (included)
10.	Electrical inlet access panel	21.	Nameplate
11.	Engine starting battery location (battery not included)

Figure 1-2Service View (see Figure 1-3for optional communications kit components)

TP-6843 1/13

Section 1 Descriptions and Service Views 15

Image 15

Contents TP-6843 1/13a VSCEngine Identification Product Identification InformationController Identification Generator Set Identification NumbersTable of Contents Table of Contents Scheduled MaintenanceAppendix a Abbreviations Safety Precautions and Instructions BatteryAccidental Starting Exhaust System Engine Backfire/Flash FireFuel System Hazardous Noise Use extreme care when handling, storing, and using fuelsHot Parts Heavy EquipmentList of Related Literature IntroductionEmission Information NameplateService Assistance Service Assistance TP-6843 1/13 Alternator Descriptions and Service ViewsIntroduction Engine Generator Set EnclosureProgrammable Interface Module PIM AccessoriesCarburetor Heater OnCue Generator Management SystemService Views 3Optional Communications Kit Components Prestart Checklist Generator Set OperationTheory of Operation Generator Set Operation Exercising the Generator SetFaults ExerciseShutdowns Fault Message ShutdownSD Condition Check Resetting the Controller After a Fault Shutdown5Controller Fault Messages Generator Set Operation TP-6843 1/13 Control and Indicators VSC Controller OperationVSC Generator Set Controller Controller Keypad LED IndicatorsLCD Display 6Autopaging Displays, Automatic ModeProcedure to Change Settings Controller PowerBattery Charging Changing Settings7Changing Settings Procedure to Set the Exerciser Setting the ExerciserSetting the Exerciser at Controller Power-up Changing the Exercise Settings8Procedure to Set the Exerciser on the VSC Controller Main Menu VSC Controller MenusEngine Metering Menu Overview MenuCalibration Generator Metering MenuGenset Run Time Menu Generator Set Information MenuGenset System Menu System Parameters for Battery Bank ChargingNominal Voltage 24V 36V 48V System Voltage, VDC Adjusting the Display Contrast Setting the ExerciserNetworking Information Menus Date and Time MenuDhcp Networking Status SubmenuPassword Networking Configuration Submenu OnCue PasswordRbus Rbus Information25Remote Devices Submenu Remote Devices SubmenuProgrammable Interface Module PIM Status Menu Event Log Procedure to View Event HistoryVSC Controller Operation TP-6843 1/13 Scheduled Maintenance Scheduled MaintenanceFuel Service Schedule, 6VSG ModelsOil Check Oil Change ProcedureLubrication System Low Oil Pressure ShutdownSpark Plugs Resetting the Maintenance TimerAir Cleaner Service Precleaner ServicePaper Element Service Cooling System Engine Starting BatteryCylinder Lubrication Storage ProcedureLubricating System Fuel SystemBattery Introduction TroubleshootingFault Messages Controller Service AccessProblem Possible Cause Recommended Action TroubleshootingAbdc Appendix a AbbreviationsSysteme international d’unites TP-6843 1/13 Appendix Appendix TP-6843 1/13 Page 2012, 2013 by Kohler Co. All rights reserved