Kohler 24VDC, 6VSG, 36VDC, 48VDC manual Generator Set Information Menu, Genset Run Time Menu

Page 33

3.12Generator Set Information Menu

The generator set model number and serial numbers are displayed (see Figure 3-13). No changes are allowed from this menu.

Model and serial numbers are factory-set and should not require changes in the field, except in the event that the controller is being replaced. A personal computer running Kohler® SiteTech™ software is required to enter the generator set model number and serial numbers on a replacement controller. Contact an authorized Kohler distributor/dealer for service.

Genset ---->	Genset M/N:
Information	6VSG-48V

3.13 Genset Run Time Menu

The data shown in Figure 3-14are displayed. No changes are allowed from this menu.

The Next Maintenance menu shows the number of hours of generator set operation until maintenance is required. The estimated date for the next scheduled maintenance is also displayed. The maintenance reminder intervals are based on the engine manufacturer’s recommendation for changing the oil. See Section 4, Scheduled Maintenance, for maintenance instructions.

After changing the oil and performing other recommended maintenance, go to the Overview menu to reset the maintenance timer. See Section 4.2.5 for instructions to reset the maintenance timer.

Genset S/N:

########

Controller S/N:

########

<---- Return

tp6804

Figure 3-13Generator Set Information Menu

Genset ---->

Run Time

Eng Runtime: 100.6 h

Eng Starts:

127

Next Maintenance: 150 h or Mar2012

<---- Return

tp68

Figure 3-14Generator Set Run Time Menu

TP-6843 1/13

Section 3 VSC Controller Operation 33

Image 33

Contents TP-6843 1/13a VSCController Identification Product Identification InformationGenerator Set Identification Numbers Engine IdentificationTable of Contents Table of Contents Scheduled MaintenanceAppendix a Abbreviations Safety Precautions and Instructions BatteryAccidental Starting Exhaust System Engine Backfire/Flash FireFuel System Hazardous Noise Use extreme care when handling, storing, and using fuelsHot Parts Heavy EquipmentList of Related Literature IntroductionEmission Information NameplateService Assistance Service Assistance TP-6843 1/13 Introduction Engine Descriptions and Service ViewsGenerator Set Enclosure AlternatorCarburetor Heater AccessoriesOnCue Generator Management System Programmable Interface Module PIMService Views 3Optional Communications Kit Components Prestart Checklist Generator Set OperationTheory of Operation Generator Set Operation Exercising the Generator SetFaults ExerciseShutdowns Fault Message ShutdownSD Condition Check Resetting the Controller After a Fault Shutdown5Controller Fault Messages Generator Set Operation TP-6843 1/13 Control and Indicators VSC Controller OperationVSC Generator Set Controller Controller Keypad LED IndicatorsLCD Display 6Autopaging Displays, Automatic ModeBattery Charging Controller PowerChanging Settings Procedure to Change Settings7Changing Settings Setting the Exerciser at Controller Power-up Setting the ExerciserChanging the Exercise Settings Procedure to Set the Exerciser8Procedure to Set the Exerciser on the VSC Controller Main Menu VSC Controller MenusEngine Metering Menu Overview MenuCalibration Generator Metering MenuGenset Run Time Menu Generator Set Information MenuGenset System Menu System Parameters for Battery Bank ChargingNominal Voltage 24V 36V 48V System Voltage, VDC Adjusting the Display Contrast Setting the ExerciserNetworking Information Menus Date and Time MenuDhcp Networking Status SubmenuPassword Networking Configuration Submenu OnCue PasswordRbus Rbus Information25Remote Devices Submenu Remote Devices SubmenuProgrammable Interface Module PIM Status Menu Event Log Procedure to View Event HistoryVSC Controller Operation TP-6843 1/13 Scheduled Maintenance Scheduled MaintenanceFuel Service Schedule, 6VSG ModelsLubrication System Oil Change ProcedureLow Oil Pressure Shutdown Oil CheckSpark Plugs Resetting the Maintenance TimerAir Cleaner Service Precleaner ServicePaper Element Service Cooling System Engine Starting BatteryLubricating System Storage ProcedureFuel System Cylinder LubricationBattery Fault Messages TroubleshootingController Service Access IntroductionProblem Possible Cause Recommended Action TroubleshootingAbdc Appendix a AbbreviationsSysteme international d’unites TP-6843 1/13 Appendix Appendix TP-6843 1/13 Page 2012, 2013 by Kohler Co. All rights reserved