Kohler 48VDC, 6VSG, 24VDC, 36VDC manual Networking Configuration Submenu OnCue Password

Page 39

3.16.2Networking Configuration Submenu (OnCue® Password)

The networking Configuration menu includes settings used for communication with the Kohler® OnCue® Generator Management System. See Figure 3-23.

For most applications, DHCP is enabled and the IP settings cannot be changed from the controller keypad. If DHCP is enabled, IP parameters are not displayed.

If DHCP is disabled (i.e., if a static IP address is required), then the IP parameters can be modified. For applications that require static IP addresses, press and hold the select button to enable editing, disable DHCP, and then step to the next parameters and enter the information.

If an error occurs while setting a parameter, an error message is displayed and then the controller exits the edit mode. Previous settings are preserved.

Password

For the initial OnCue® setup, you will be required to reset the OnCue® password on the VSC controller, and then enter it into the OnCue® software. To reset the password, follow the instructions in Section 3-22.

Note: The password is displayed for only 10 seconds. Be sure to write down the password and serial number.

A new password is generated each time the reset password procedure is performed. If the password is reset after the OnCue® system has been set up, the connection will be lost. Enter the new password in OnCue® to reconnect.

Networking---->

Information

Networking---->

Status

Networking

Configuration

Reset OnCue Password

HOLD

Reset OnCue

Password? No

UP arrow for YES,

Down arrow for NO.

DHCP:

Enabled

<---- Return

Reset OnCue

Password? Yes

Press Select to enter YES or NO as displayed. New password is displayed for approximately 10 seconds.

S/N: 1234567

New PW: 12345

tp6804

Figure 3-23Network Configuration Submenu

TP-6843 1/13

Section 3 VSC Controller Operation 39

Image 39

Contents TP-6843 1/13a VSCEngine Identification Product Identification InformationController Identification Generator Set Identification NumbersTable of Contents Table of Contents Scheduled MaintenanceAppendix a Abbreviations Safety Precautions and Instructions BatteryAccidental Starting Exhaust System Engine Backfire/Flash FireFuel System Hazardous Noise Use extreme care when handling, storing, and using fuelsHot Parts Heavy EquipmentList of Related Literature IntroductionEmission Information NameplateService Assistance Service Assistance TP-6843 1/13 Alternator Descriptions and Service ViewsIntroduction Engine Generator Set EnclosureProgrammable Interface Module PIM AccessoriesCarburetor Heater OnCue Generator Management SystemService Views 3Optional Communications Kit Components Prestart Checklist Generator Set OperationTheory of Operation Generator Set Operation Exercising the Generator SetFaults ExerciseShutdowns Fault Message ShutdownSD Condition Check Resetting the Controller After a Fault Shutdown5Controller Fault Messages Generator Set Operation TP-6843 1/13 Control and Indicators VSC Controller OperationVSC Generator Set Controller Controller Keypad LED IndicatorsLCD Display 6Autopaging Displays, Automatic ModeProcedure to Change Settings Controller PowerBattery Charging Changing Settings7Changing Settings Procedure to Set the Exerciser Setting the ExerciserSetting the Exerciser at Controller Power-up Changing the Exercise Settings8Procedure to Set the Exerciser on the VSC Controller Main Menu VSC Controller MenusEngine Metering Menu Overview MenuCalibration Generator Metering MenuGenset Run Time Menu Generator Set Information MenuGenset System Menu System Parameters for Battery Bank ChargingNominal Voltage 24V 36V 48V System Voltage, VDC Adjusting the Display Contrast Setting the ExerciserNetworking Information Menus Date and Time MenuDhcp Networking Status SubmenuPassword Networking Configuration Submenu OnCue PasswordRbus Rbus Information25Remote Devices Submenu Remote Devices SubmenuProgrammable Interface Module PIM Status Menu Event Log Procedure to View Event HistoryVSC Controller Operation TP-6843 1/13 Scheduled Maintenance Scheduled MaintenanceFuel Service Schedule, 6VSG ModelsOil Check Oil Change ProcedureLubrication System Low Oil Pressure ShutdownSpark Plugs Resetting the Maintenance TimerAir Cleaner Service Precleaner ServicePaper Element Service Cooling System Engine Starting BatteryCylinder Lubrication Storage ProcedureLubricating System Fuel SystemBattery Introduction TroubleshootingFault Messages Controller Service AccessProblem Possible Cause Recommended Action TroubleshootingAbdc Appendix a AbbreviationsSysteme international d’unites TP-6843 1/13 Appendix Appendix TP-6843 1/13 Page 2012, 2013 by Kohler Co. All rights reserved