Kohler 24VDC, 6VSG, 36VDC, 48VDC manual Date and Time Menu, Networking Information Menus

Page 37

3.15 Date and Time Menu

The date and time will typically be set at controller powerup. To change the date, time, or time format (12 hour or 24 hour), use the Date and Time menu. See Figure 3-20.

3.16 Networking Information Menus

Use the networking menus to view and adjust communication settings for systems with remote RBUS devices such as a PIM, and for systems that use the Kohler® OnCue® Generator Management System.

RBUS is a proprietary RS-485 communications protocol.

The Networking Information menu leads to submenus for network and RBUS communication settings. See Figure 3-21.

	Date and	Date:
	Time	Date:
	Time

02Dec2011

Time:

12:34pm

Time Format:

12hr

<---- Return

tp6804

To change the date and time, press the Select button See Figure 3-7 for instructions.

Figure 3-20Date and Time Menu

Networking---->

Information

Networking---->

Status

Networking---->

Configuration

RBUS ---->

Information

<---- Return

NS See Figure 3-22.

NC See Figure 3-23.

RB See Figure 3-24.

tp6810

Figure 3-21Networking Information Menu

TP-6843 1/13

Section 3 VSC Controller Operation 37

Image 37

Contents TP-6843 1/13a VSCController Identification Product Identification InformationGenerator Set Identification Numbers Engine IdentificationTable of Contents Scheduled Maintenance Table of ContentsAppendix a Abbreviations Battery Safety Precautions and InstructionsAccidental Starting Exhaust System Engine Backfire/Flash FireFuel System Hazardous Noise Use extreme care when handling, storing, and using fuelsHot Parts Heavy EquipmentList of Related Literature IntroductionEmission Information NameplateService Assistance Service Assistance TP-6843 1/13 Introduction Engine Descriptions and Service ViewsGenerator Set Enclosure AlternatorCarburetor Heater AccessoriesOnCue Generator Management System Programmable Interface Module PIMService Views 3Optional Communications Kit Components Generator Set Operation Prestart ChecklistTheory of Operation Generator Set Operation Exercising the Generator SetExercise FaultsShutdowns Fault Message ShutdownSD Condition Check Resetting the Controller After a Fault Shutdown5Controller Fault Messages Generator Set Operation TP-6843 1/13 VSC Controller Operation Control and IndicatorsVSC Generator Set Controller Controller Keypad LED IndicatorsLCD Display 6Autopaging Displays, Automatic ModeBattery Charging Controller PowerChanging Settings Procedure to Change Settings7Changing Settings Setting the Exerciser at Controller Power-up Setting the ExerciserChanging the Exercise Settings Procedure to Set the Exerciser8Procedure to Set the Exerciser on the VSC Controller Main Menu VSC Controller MenusEngine Metering Menu Overview MenuCalibration Generator Metering MenuGenset Run Time Menu Generator Set Information MenuGenset System Menu System Parameters for Battery Bank ChargingNominal Voltage 24V 36V 48V System Voltage, VDC Adjusting the Display Contrast Setting the ExerciserNetworking Information Menus Date and Time MenuDhcp Networking Status SubmenuPassword Networking Configuration Submenu OnCue PasswordRbus Rbus Information25Remote Devices Submenu Remote Devices SubmenuProgrammable Interface Module PIM Status Menu Event Log Procedure to View Event HistoryVSC Controller Operation TP-6843 1/13 Scheduled Maintenance Scheduled MaintenanceFuel Service Schedule, 6VSG ModelsLubrication System Oil Change ProcedureLow Oil Pressure Shutdown Oil CheckSpark Plugs Resetting the Maintenance TimerPrecleaner Service Air Cleaner ServicePaper Element Service Cooling System Engine Starting BatteryLubricating System Storage ProcedureFuel System Cylinder LubricationBattery Fault Messages TroubleshootingController Service Access IntroductionProblem Possible Cause Recommended Action TroubleshootingAbdc Appendix a AbbreviationsSysteme international d’unites TP-6843 1/13 Appendix Appendix TP-6843 1/13 Page 2012, 2013 by Kohler Co. All rights reserved