Kohler 24VDC, 6VSG, 36VDC, 48VDC manual LCD Display, 6Autopaging Displays, Automatic Mode

Page 25

3.2.3LCD Display

The controller is equipped with a two-line x 16-character backlit digital display with adjustable contrast. When the generator is running, the controller automatically scrolls through the displays shown in Figure 3-5.The VSC controller measures and displays the average DC output voltage on the auto-scrolling display. When the system is in standby mode and the controller is in AUTO, the screens shown in Figure 3-6are displayed.

When a fault or warning condition exists, the controller will show the corresponding message. See Section 2.6 for more information about faults.

Controller menus display power system information, including status information for the engine, generator, and optional RBUS accessories, exercise settings, and event history. Some menus allow changes to the controller settings. See Sections 3.7 through 3.18 for menu diagrams.

Active Alert

Genset Status

Running

Voltage: 54V

Load: 73%

Engine: 125F

Oil Pressure: Okay

Battery

13.3V

Engine Runtime: 100.6 h

Date: 02DEC2011

Time: HR:MNpm

Sample data shown.

Figure 3-5Autopaging Displays, Generator Running

The display contrast is adjustable. Navigate to the Genset System menu and step down to the Contrast screen. Press the Select button, and then use the up and down arrow buttons to adjust the contrast. See Section 3.5, Changing Settings, and Section 3.14, Genset System Menu.

The display backlight turns off after about a minute of no activity. The backlight turns on when a button is pressed or when the generator set starts.

Active Alert

Genset Status

Standby

Battery

13.3V

Engine Runtime: 100.6 h

Date: 02DEC2011

Time: HR:MNpm

Next Exercise: 09:00p 09Dec2011

Next Maintenance: 150 h or Mar2012

Sample data shown.

tp6804

Figure 3-6Autopaging Displays, Automatic Mode

TP-6843 1/13

Section 3 VSC Controller Operation 25

Image 25

Contents TP-6843 1/13a VSCController Identification Product Identification InformationGenerator Set Identification Numbers Engine IdentificationTable of Contents Scheduled Maintenance Table of ContentsAppendix a Abbreviations Battery Safety Precautions and InstructionsAccidental Starting Exhaust System Engine Backfire/Flash FireFuel System Hazardous Noise Use extreme care when handling, storing, and using fuelsHot Parts Heavy EquipmentList of Related Literature IntroductionEmission Information NameplateService Assistance Service Assistance TP-6843 1/13 Introduction Engine Descriptions and Service ViewsGenerator Set Enclosure AlternatorCarburetor Heater AccessoriesOnCue Generator Management System Programmable Interface Module PIMService Views 3Optional Communications Kit Components Generator Set Operation Prestart ChecklistTheory of Operation Generator Set Operation Exercising the Generator SetExercise FaultsShutdowns Fault Message ShutdownSD Condition Check Resetting the Controller After a Fault Shutdown5Controller Fault Messages Generator Set Operation TP-6843 1/13 VSC Controller Operation Control and IndicatorsVSC Generator Set Controller Controller Keypad LED IndicatorsLCD Display 6Autopaging Displays, Automatic ModeBattery Charging Controller PowerChanging Settings Procedure to Change Settings7Changing Settings Setting the Exerciser at Controller Power-up Setting the ExerciserChanging the Exercise Settings Procedure to Set the Exerciser8Procedure to Set the Exerciser on the VSC Controller Main Menu VSC Controller MenusEngine Metering Menu Overview MenuCalibration Generator Metering MenuGenset Run Time Menu Generator Set Information MenuGenset System Menu System Parameters for Battery Bank ChargingNominal Voltage 24V 36V 48V System Voltage, VDC Adjusting the Display Contrast Setting the ExerciserNetworking Information Menus Date and Time MenuDhcp Networking Status SubmenuPassword Networking Configuration Submenu OnCue PasswordRbus Rbus Information25Remote Devices Submenu Remote Devices SubmenuProgrammable Interface Module PIM Status Menu Event Log Procedure to View Event HistoryVSC Controller Operation TP-6843 1/13 Scheduled Maintenance Scheduled MaintenanceFuel Service Schedule, 6VSG ModelsLubrication System Oil Change ProcedureLow Oil Pressure Shutdown Oil CheckSpark Plugs Resetting the Maintenance TimerPrecleaner Service Air Cleaner ServicePaper Element Service Cooling System Engine Starting BatteryLubricating System Storage ProcedureFuel System Cylinder LubricationBattery Fault Messages TroubleshootingController Service Access IntroductionProblem Possible Cause Recommended Action TroubleshootingAbdc Appendix a AbbreviationsSysteme international d’unites TP-6843 1/13 Appendix Appendix TP-6843 1/13 Page 2012, 2013 by Kohler Co. All rights reserved