Kohler 36VDC, 6VSG, 24VDC, 48VDC manual VSC Controller Menus, Main Menu

Page 30

3.7 VSC Controller Menus

Controller menus display power system information, including status information for the engine, generator, and optional RBUS accessories, exercise settings, and event history. Some menus allow changes to the controller settings.

Diagrams in the following sections show how to navigate through the menus.

Note: Use caution when navigating the controller menus. In some menus, pressing the Select button can enable editing of the controller settings. Changing the settings to incorrect values can adversely affect generator set operation or render the unit inoperable.

If a setting on the controller display is flashing, edit mode has been enabled. Press the OFF or AUTO button to exit the edit mode.

3.8 Main Menu

Press the Select button once to bring up the main menu. Overview is displayed. See Figure 3-9.Press the down arrow button to step to the next menu, Engine Metering. Use the UP and DOWN arrow buttons to step up and down through the menus shown in Figure 3-9.

The controller will exit the main menu after 5 minutes if no buttons are pressed. To exit the main menu immediately, press the controller’s OFF or AUTO button.

Status

Displays

Overview ---->

1.2 h

Press the Up and Down arrow buttons to move between menus.

Press OFF or AUTO to exit the menus.

Engine ---->

Metering

Generator---->

Metering

Date ---->

and Time

Genset ---->

Information

Network ---->

Information

Genset ---->

Run Time

PIM ---->

Status

Genset ---->

System

Event Log---->

Figure 3-9VSC Main Menu

30 Section 3 VSC Controller Operation

TP-6843 1/13

Image 30

Contents VSC TP-6843 1/13aGenerator Set Identification Numbers Product Identification InformationController Identification Engine IdentificationTable of Contents Table of Contents Scheduled MaintenanceAppendix a Abbreviations Safety Precautions and Instructions BatteryAccidental Starting Engine Backfire/Flash Fire Exhaust SystemUse extreme care when handling, storing, and using fuels Fuel System Hazardous NoiseHeavy Equipment Hot PartsIntroduction List of Related LiteratureNameplate Emission InformationService Assistance Service Assistance TP-6843 1/13 Generator Set Enclosure Descriptions and Service ViewsIntroduction Engine AlternatorOnCue Generator Management System AccessoriesCarburetor Heater Programmable Interface Module PIMService Views 3Optional Communications Kit Components Prestart Checklist Generator Set OperationTheory of Operation Exercising the Generator Set Generator Set OperationFaults ExerciseShutdowns Resetting the Controller After a Fault Shutdown Fault Message ShutdownSD Condition Check5Controller Fault Messages Generator Set Operation TP-6843 1/13 Control and Indicators VSC Controller OperationVSC Generator Set Controller LED Indicators Controller Keypad6Autopaging Displays, Automatic Mode LCD DisplayChanging Settings Controller PowerBattery Charging Procedure to Change Settings7Changing Settings Changing the Exercise Settings Setting the ExerciserSetting the Exerciser at Controller Power-up Procedure to Set the Exerciser8Procedure to Set the Exerciser on the VSC Controller VSC Controller Menus Main MenuOverview Menu Engine Metering MenuGenerator Metering Menu CalibrationGenerator Set Information Menu Genset Run Time MenuSystem Parameters for Battery Bank Charging Genset System MenuNominal Voltage 24V 36V 48V System Voltage, VDC Setting the Exerciser Adjusting the Display ContrastDate and Time Menu Networking Information MenusNetworking Status Submenu DhcpNetworking Configuration Submenu OnCue Password PasswordRbus Information RbusRemote Devices Submenu 25Remote Devices SubmenuProgrammable Interface Module PIM Status Menu Procedure to View Event History Event LogVSC Controller Operation TP-6843 1/13 Scheduled Maintenance Scheduled MaintenanceService Schedule, 6VSG Models FuelLow Oil Pressure Shutdown Oil Change ProcedureLubrication System Oil CheckResetting the Maintenance Timer Spark PlugsAir Cleaner Service Precleaner ServicePaper Element Service Engine Starting Battery Cooling SystemFuel System Storage ProcedureLubricating System Cylinder LubricationBattery Controller Service Access TroubleshootingFault Messages IntroductionTroubleshooting Problem Possible Cause Recommended ActionAppendix a Abbreviations AbdcSysteme international d’unites TP-6843 1/13 Appendix Appendix TP-6843 1/13 Page 2012, 2013 by Kohler Co. All rights reserved