Kohler 36VDC, 6VSG, 24VDC, 48VDC manual Networking Status Submenu, Dhcp

Page 38

3.16.1 Networking Status Submenu

The Networking Status submenu contains settings for OnCue®. See Figure 3-22.See the OnCue® Software Operation Manual for information about the appropriate network settings for OnCue®. Changes to these settings are not typically required.

If DHCP is enabled, IP parameters are not displayed. If DHCP is disabled (i.e., if a static IP address is used), the IP parameters are displayed.

To enable or disable DHCP and change the IP settings, go to the Networking Configuration menu. See Section 3.16.2.

Networking---->

Information

Networking---->

Status

OnCue Status: Connected

DHCP:

Enabled

IP Address: 123.456.789.123

Subnet Mask: 123.456.789.123

Gateway:

123.456.789.123

DNS 1: 123.456.789.123

DNS 2:

123.456.789.123

Ethernet Status: Disconnected

OnCue Server: 123.456.789.123

<---- Return

tp68

Figure 3-22Network Status Submenu

38 Section 3 VSC Controller Operation

TP-6843 1/13

Image 38

Contents VSC TP-6843 1/13aGenerator Set Identification Numbers Product Identification InformationController Identification Engine IdentificationTable of Contents Appendix a Abbreviations Table of ContentsScheduled Maintenance Accidental Starting Safety Precautions and InstructionsBattery Engine Backfire/Flash Fire Exhaust SystemUse extreme care when handling, storing, and using fuels Fuel System Hazardous NoiseHeavy Equipment Hot PartsIntroduction List of Related LiteratureNameplate Emission InformationService Assistance Service Assistance TP-6843 1/13 Generator Set Enclosure Descriptions and Service ViewsIntroduction Engine AlternatorOnCue Generator Management System AccessoriesCarburetor Heater Programmable Interface Module PIMService Views 3Optional Communications Kit Components Theory of Operation Prestart ChecklistGenerator Set Operation Exercising the Generator Set Generator Set OperationShutdowns FaultsExercise Resetting the Controller After a Fault Shutdown Fault Message ShutdownSD Condition Check5Controller Fault Messages Generator Set Operation TP-6843 1/13 VSC Generator Set Controller Control and IndicatorsVSC Controller Operation LED Indicators Controller Keypad6Autopaging Displays, Automatic Mode LCD DisplayChanging Settings Controller PowerBattery Charging Procedure to Change Settings7Changing Settings Changing the Exercise Settings Setting the ExerciserSetting the Exerciser at Controller Power-up Procedure to Set the Exerciser8Procedure to Set the Exerciser on the VSC Controller VSC Controller Menus Main MenuOverview Menu Engine Metering MenuGenerator Metering Menu CalibrationGenerator Set Information Menu Genset Run Time MenuSystem Parameters for Battery Bank Charging Genset System MenuNominal Voltage 24V 36V 48V System Voltage, VDC Setting the Exerciser Adjusting the Display ContrastDate and Time Menu Networking Information MenusNetworking Status Submenu DhcpNetworking Configuration Submenu OnCue Password PasswordRbus Information RbusRemote Devices Submenu 25Remote Devices SubmenuProgrammable Interface Module PIM Status Menu Procedure to View Event History Event LogVSC Controller Operation TP-6843 1/13 Scheduled Maintenance Scheduled MaintenanceService Schedule, 6VSG Models FuelLow Oil Pressure Shutdown Oil Change ProcedureLubrication System Oil CheckResetting the Maintenance Timer Spark PlugsPaper Element Service Air Cleaner ServicePrecleaner Service Engine Starting Battery Cooling SystemFuel System Storage ProcedureLubricating System Cylinder LubricationBattery Controller Service Access TroubleshootingFault Messages IntroductionTroubleshooting Problem Possible Cause Recommended ActionAppendix a Abbreviations AbdcSysteme international d’unites TP-6843 1/13 Appendix Appendix TP-6843 1/13 Page 2012, 2013 by Kohler Co. All rights reserved