Kohler 48VDC, 6VSG, 24VDC, 36VDC manual 7Changing Settings

Page 27

Changing Date/Time

1. Press the Select button to enter the main menu.

8.

When the correct date is shown, press the Select

 

 

 

 

 

button. The saved date is shown.

Press:

Display:

Overview ---->

 

 

 

 

1.2 h

 

Press:

Display:

Date:

 

 

 

 

 

 

 

 

03Jan2012

 

 

 

 

 

 

 

2. Press the down arrow button until the desired

 

 

 

 

menu is displayed. See Figure 3-9. Date and Time

9.

Press the down arrow button to step to the next

are used for this example.

 

 

 

menu.

 

 

 

 

Date

---->

Press:

Display:

Time:

Press:

Display:

01:49pm

and Time

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10.

Repeat steps 5 and 6, using the arrow and select

3. Press the Select button to enter the Date and Time

 

buttons to set and save the time.

menu.

 

 

 

Note: To change from am to pm, press the up arrow

 

 

 

 

Press:

Display:

Date:

 

 

key to increase the hour until the correct hour

05Dec2011

 

and pm is displayed.

 

 

 

 

 

11.

In the time format menu, press Select and then

 

 

 

 

 

press the up or down arrow button to change the

4. To change the date and time settings, press the

 

format, 12 hr. or 24 hr. Press Select to save the

Select button again. The year will flash.

 

displayed format.

 

 

 

Date:

 

12.

Press the

down arrow button. Return is

Press:

Display:

 

 

displayed.

 

 

05Dec2011

 

 

 

 

 

 

 

 

 

 

 

 

 

Press:

Display:

<---- Return

 

 

 

 

 

5.Press the up or down arrow buttons to change the year.

 

 

 

13. Press Select to return to the Date and Time

 

 

 

menu.

 

 

Date:

 

 

Press:

OR

Display:

 

Date ---->

05Dec2012

 

 

 

Press:

 

 

 

Display:

 

 

 

 

and Time

6. When the correct year is shown, press the Select

14. Press the Up or Down arrow buttons to step to a

different menu.

button. The year is saved and the next setting

 

 

(month) flashes.

 

15. Press Auto to signal the controller to exit the

 

 

 

 

 

Date:

menus and return to the generator set status

Press:

 

display.

 

Display:

 

 

 

 

05Dec2012

 

 

 

 

 

 

Genset State

 

 

 

Press:

Display:

 

 

 

 

Standby

7. Repeat steps 5 and 6, using the arrow and select

 

AUTO

buttons to set the month and the date.

Note: If no buttons are pressed, the controller returns

 

 

 

 

 

 

 

to the status display after 5 minutes.

Figure 3-7Changing Settings

TP-6843 1/13

Section 3 VSC Controller Operation 27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents TP-6843 1/13a VSCEngine Identification Product Identification InformationController Identification Generator Set Identification NumbersTable of Contents Table of Contents Scheduled MaintenanceAppendix a Abbreviations Safety Precautions and Instructions BatteryAccidental Starting Exhaust System Engine Backfire/Flash FireFuel System Hazardous Noise Use extreme care when handling, storing, and using fuelsHot Parts Heavy EquipmentList of Related Literature IntroductionEmission Information NameplateService Assistance Service Assistance TP-6843 1/13 Alternator Descriptions and Service ViewsIntroduction Engine Generator Set EnclosureProgrammable Interface Module PIM AccessoriesCarburetor Heater OnCue Generator Management SystemService Views 3Optional Communications Kit Components Prestart Checklist Generator Set OperationTheory of Operation Generator Set Operation Exercising the Generator SetFaults ExerciseShutdowns Fault Message ShutdownSD Condition Check Resetting the Controller After a Fault Shutdown5Controller Fault Messages Generator Set Operation TP-6843 1/13 Control and Indicators VSC Controller OperationVSC Generator Set Controller Controller Keypad LED IndicatorsLCD Display 6Autopaging Displays, Automatic ModeProcedure to Change Settings Controller PowerBattery Charging Changing Settings7Changing Settings Procedure to Set the Exerciser Setting the ExerciserSetting the Exerciser at Controller Power-up Changing the Exercise Settings8Procedure to Set the Exerciser on the VSC Controller Main Menu VSC Controller MenusEngine Metering Menu Overview MenuCalibration Generator Metering MenuGenset Run Time Menu Generator Set Information MenuGenset System Menu System Parameters for Battery Bank ChargingNominal Voltage 24V 36V 48V System Voltage, VDC Adjusting the Display Contrast Setting the ExerciserNetworking Information Menus Date and Time MenuDhcp Networking Status SubmenuPassword Networking Configuration Submenu OnCue PasswordRbus Rbus Information25Remote Devices Submenu Remote Devices SubmenuProgrammable Interface Module PIM Status Menu Event Log Procedure to View Event HistoryVSC Controller Operation TP-6843 1/13 Scheduled Maintenance Scheduled MaintenanceFuel Service Schedule, 6VSG ModelsOil Check Oil Change ProcedureLubrication System Low Oil Pressure ShutdownSpark Plugs Resetting the Maintenance TimerAir Cleaner Service Precleaner ServicePaper Element Service Cooling System Engine Starting BatteryCylinder Lubrication Storage ProcedureLubricating System Fuel SystemBattery Introduction TroubleshootingFault Messages Controller Service AccessProblem Possible Cause Recommended Action TroubleshootingAbdc Appendix a AbbreviationsSysteme international d’unites TP-6843 1/13 Appendix Appendix TP-6843 1/13 Page 2012, 2013 by Kohler Co. All rights reserved
Top Page Image Contents