Black & Decker SPCM1936, CM1936Z Preparation, Unpacking Figures A, B, Handle Assemblyfigure C

Page 6

PREPARATION

 

 

PLEASE REFER TO DIAGRAMS (A, B, C...) AND ITEM NUMBERS (1, 2, 3...) AS NOTED THROUGHOUT MANUAL. FOR EXAMPLE,

A-1 REFERS TO ITEM 1 IN FIGURE A.

 

UNPACKING - (FIGURES A, B)

 

CAUTION: Pinch point. To avoid being pinched, keep fingers away

from area between handle and plates.

 

STEP 1:

 

 

Carefully cut down the sides of the box on the opposite end of the handle

and fold the flap down as shown.

WARNING:

Sharp blade. Keep

body parts away from blade.

 

 

WithSTEPthe2: carton end cut open, remove the cardboard filler, charger,

B

 

accessory bag and grass bag and push the mower out of the opened

 

 

carton.

 

 

ASSEMBLY

 

 

Tools required for assembly, not supplied:

 

 

Adjustable or 1/2 inch (13mm) wrench.

 

 

HANDLE ASSEMBLY(FIGURE C)

2

1

1. Position the handle so that the handle holes line up with the deck side

plate holes. The handle quick adjust knobs C-2will line up with the

 

deck side plate top holes.

 

 

2. Place handle attachment bolts C-1through the handle holes and

 

 

thread into the deck side plate. Before tightening repeat for other side.

 

 

3. Tighten handle attachment bolts C-1securely using adjustable or 1/2

 

 

inch (13mm) wrench.

 

 

4. To set desired handle height refer to handle adjustment. Do not push

 

 

or use mower unless handle is properly fastened and secured to

 

 

mower.

2

 

The handle quick adjust knobs C-2 will appear as shown in figure C

 

when they are fully engaged into the plates.

 

CAUTION: Pinch point. To avoid being pinched, keep fingers away from

1

 

area between handle and plates when raising or adjusting.

 

HANDLE ADJUSTMENT (FIGURE D)

 

 

1. Remove safety key.

 

1

2. Hold handle with one hand, pull out and rotate one handle quick

 

adjust knob D-1on mower handle a quarter-turn to release the pin

 

 

from the metal plate hole. Handle quick adjust knob D-1will remain

 

 

in this retracted position. Repeat for the opposite side knob. Now the

 

 

handle is free to move into another handle height position.

 

 

3. Move the handle to desired height position. Taller users will prefer

 

 

using the top hole position, while shorter users may prefer the bottom

 

 

hole position. While holding handle with one hand, pull out and rotate

 

 

one handle quick adjust knob D-1a quarter-turn to re-engage pin

 

 

into metal plate hole. Repeat for the other knob.

 

 

4. Shake handle slightly to ensure handle pins are fully engaged prior to

 

 

using mower. Do not push or use the mower unless handle is properly

 

 

fastened and secured to mower. The handle quick adjust knobs D-1

 

 

will appear as shown in figure D when the knob pins are fully engaged

1

 

into the plates.

 

CAUTION: Pinch point. To avoid being pinched, keep fingers away from

 

 

area between handle and plates when raising or adjusting.

 

 

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Please Read Before Returning this Product for ANY Reason KEY Information YOU should KnowVEA EL Español EN LA Contraportada Read ALL Instructions To Reduce Risk of InjuryUSE of Extension Cords Volts310 Functional Description CM1936ZFunctional Description SPCM1936 Handle Adjustment Figure D AssemblyHandle Assemblyfigure C PreparationAssembling the Grass Catcher Figures E1, E2, E3, E4 Grassbag Frame ClipRemoving Battery from Mower Figure BatteryBatteryruntime Indicator Figure H Charger Safety RulesCharging PROCEDURE- Figures J, K, L Know Your Mower Safety KEYTo Turn Mower on ON-OFF Switch Bail Handle Figure MMeets Cpsc Safety Requirements Variable Speed Self Drive System Figure NFor Models Without ON-DEMAND Removing Mulch Insert Figure O Installing Mulch Insert Figure PInstalling Grass Catcher Figure Q, R Operatingthe Mower for DischargingYour mower is now in Bagging mode Mulching Mode Discharge ModeBagging Mode For Models with ON-DEMANDMulching Mowing Tips MaintenanceRemoving and Installing Blade Figure U 19mm wrench U-2 as shown in figure UBlade Balancing CleaningBlade Sharpening LubricationBattery Service and Installation Storage PositionOFF-SEASON Storage Troubleshooting Guide Problem SolutionWarranties Center for ServicingGuide DʼUTILISATION Lire Toutes CES Directives Conserver CES Mesures Utilisation DE Rallonges Description Fonctionnelle CM1936Z Description Fonctionnelle SPCM1936 Déballage Illustrations A, B PréparationAssemblage Ensemble DE Poignée Figure CMontage DU Collecteur Dherbe Illustrations E1, E2, E3 ET E4 Règles DE Sécurité Pour LE Chargeur PileRetrait DE LA Pile DE LA Tondeuse Illustration Avec Lecentre DE Réparation DE Votre Région OU Composer LEProcédure DE CHARGE- ILLUSTRATIONSJ, K, L Lire LE Mode Demploi ET LES Règles DE Sécurité AvantFonctionnement Connaître SA TondeuseSPCM1936 Seulement Démarrage DE LA TondeuseInterrupteur DE MARCHE/ARRÊT Anse Illustration M Surcharge DE LA TondeuseInstallation DU Collecteur Dherbe Installation DE LA Pièce DE DéchiquetageTondre EN Mode Déjection Pour LES Modèles Sans « Sélection DEMode densachage Pour LES Modèles Avec « Sélection DE Mode »Mode déjection Mode de déchiquetageEntretien Conseils Pour Tondre LA PelouseConseils Pour LE Déchiquetage Lors DE Laffûtage DE LA Lame Retrait ET Installation DE LA Lame Illustration UAffûtage DE LA Lame Affûtage DE LA Lame Dans UN ÉtauPrévention DE LA Corrosion Équilibrage DE LA LameNettoyage Transport ET RangementLE Sceau Srprc Recyclage DES Piles Rechargeables Entretien ET Installation DE LA PileRangement Hors Saison 800Problème Solution Coupe inégale et une décharge rapide de la batterieRemarque Page Manual DE Instrucciones Pautas DE SEGURIDAD/DEFINICIONES Page USO DE Cables Prolongadores Volts Longitud total del cable en piesDescripción DE LAS Funciones CM1936Z Descripción DE LAS Funciones SPCM1936 Desembalaje Figuras A, A1, A2 PreparaciónEnsamblaje Ensamblaje DEL Mango Figura CEnsamblado DEL Recolector DE Césped Figuras E1, E2, E3, E4 Retiro DE LA Batería DE LA Podadora BateríaIndicador DE Duración DE LA Batería Normas DE Seguridad DEL CargadorProcedimiento DE Carga Figura J, K, L Conozca LA PodadoraLlave DE Seguridad Sobrecarga DE LA Podadora Para Encender LA PodadoraSPCM1936 Únicamente Cumple CON LOS Requisitos DE Seguridad DE LA CpscInstalación DE LA Pieza Para Mantillo Figura Protector DE Seguridad Y Puerta Trasera Figura OPara Modelos SIN Operación Según Operación DE LA Podadora Para DescargaModo de recolección en bolsa Para Modelos CON Operación Según RequerimientoModo de descarga Modo de formación de mantilloMantenimiento Consejos Para EL Corte DE CéspedConsejos Para EL Corte DE Césped Para Formar Mantillo AL Afilar LA Hoja Retiro E Instalación DE LA Hoja Figura UAfilado DE LA Hoja Para Afilar LA Hoja EN UNA PrensaLimpieza Simetría DE LA HojaLubricación Prevención DE LA CorrosiónMantenimiento E Instalación DE LA Batería EL Sello Rbrc Reciclado DE BateríasGarantías Garantía en la cubiertaGuía DE Solución DE Problemas Problema SoluciónProblema Product Infomation · Identificación DEL ProductoAños DE Garantia Esta Garantia no Aplica CuandoSolamente Para Propositos DE Mexico

CM1936Z, SPCM1936 specifications

The Black & Decker SPCM1936, also known as the CM1936Z, represents a standout choice in the realm of cordless lawn mowers, combining innovation with user-friendly design to deliver efficient lawn care. This model is powered by a robust 36V lithium-ion battery, which offers ample runtime to handle medium to large-sized yards without the nuisance of cords or gas.

One of the primary features of the SPCM1936 is its lightweight construction, making it easy to maneuver across various terrains. Weighing significantly less than many traditional gas mowers, the SPCM1936 allows users to navigate tight spaces and intricate landscaping effortlessly.

The mower comes equipped with a 19-inch cutting deck, striking a balance between agility and the ability to cover large areas quickly. The deck material is designed to be durable yet lightweight, ensuring longevity and ease of use. This model offers a 6-position height adjustment feature, allowing users to customize their mowing height from 1-inch to 3-inches, giving flexibility for different grass types and seasonal changes.

Technology is at the forefront of the Black & Decker SPCM1936's design. It boasts a Smart Cut technology, which automatically adjusts the power of the motor based on the thickness of the grass being cut. This ensures optimal performance while conserving battery life, enhancing efficiency and extending the runtime during use.

Another critical feature is the mower's EdgeMax design, which allows the blade to cut closer to edges and flower beds, reducing the need for trim work and making the mowing process quicker and less labor-intensive. The mower also features a bagging system that collects grass clippings, promoting cleaner yard maintenance, while its mulching capability returns nutrients back to the soil.

The SPCM1936 is designed with user comfort in mind, featuring an easy-to-handle ergonomic grip and a foldable handle for convenient storage. With safety features like a safety key and a blade brake, users can operate the mower with peace of mind.

In summary, the Black & Decker SPCM1936, CM1936Z is an advanced, efficient, and user-friendly cordless lawn mower, perfect for homeowners seeking reliability and ease in lawn maintenance. Its combination of power, innovative technology, and smart design makes it a top contender in the cordless mower market.
Top Page Image Contents