Samsung SCR-3000P 4Alarm Record Setup, PAL, OFF, OFF, N.O, OFF, OFF, NTSC, STOP, N. C, AUTO, [ON/OFF], [ON/OFF], [N.C./N.O.], Picture Rate, ➂ALARM BUZZER, Time-LapseMode

DIGITAL VIDEO RECORDER

Note

The following table shows how long it would take to fill up an 80GB HDD for each field rate.

(Recording time for each field rate may slightly vary depending on the type of input video singal.)

			Time-Lapse Mode
Picture Rate		VERY HIGH	HIGH	NORMAL	LOW
		80GB	80GB	80GB	80GB
	60.0 FPS	11 H	13 H	19 H	25 H
	30.0 FPS	22 H	26 H	37 H	49 H
	15.0 FPS	44 H	53 H	74 H	99 H
	10.0 FPS	65 H	79 H	111 H	148 H
NTSC	7.5 FPS	87 H	106 H	148 H	198 H
	5.0 FPS	131 H	159 H	222 H	296 H
	2.5 FPS	261 H	317 H	444 H	593 H
	1.0 FPS	654 H	794 H	1,111 H	1,481 H
	0.5 FPS	1,307 H	1,587H	2,222 H	2,963 H
	50.0 FPS	13 H	19 H	27 H	36 H
	25.0 FPS	26 H	38 H	53 H	71 H
	12.5 FPS	52 H	76 H	107 H	142 H
PAL	8.3 FPS	78 H	114 H	160 H	213 H
	6.3 FPS	105 H	152 H	213 H	284 H
	5.0 FPS	131 H	190 H	267 H	356 H
	2.5 FPS	261 H	381 H	533 H	711 H
	1.0 FPS	654 H	952 H	1,333 H	1,778 H
	0.5 FPS	1,307 H	1,905 H	2,667 H	3,556 H

4Alarm Record Setup

The following illustrates the intial setting of the ALARM RECORD SETUP menu.

ALARM RECORD SETUP

ALARM SIGNAL DETECTION		OFF
ALARM SIGNAL POLARITY		N.O.
ALARM BUZZER		ON
MAIN ALARM	TIME	10 SECOND
PRE ALARM	TIME LIMIT	2 SECOND
POST ALARM TIME LIMIT		OFF
MAIN ALARM PICTURE RATE		30.0 FPS
MOTION DETECTION		OFF
SET AREA	& SENSITIVITY
MOVE=[ /❷/➛/❿] SELECT=[		] EXIT=[MENU]

①ALARM SIGNAL DETECTION

You shall select ON to start recording in the event of alarming and select OFF to prevent recording in the event of alarming. If you set the ALARM SIGNAL DETECTION to ON and exit the menu, the system will begin recording whenever alarm occurs. To force stop the recording during the alarm recording, press and hold the STOP( ) button for 3 seconds. Then, the recording by the current alarm will be stoppted, and the alarm recording will not be per- formed for the next 5 seconds even if alarm occurs. To completely stop the alarm recording, go into the menu within that 5 seconds to set the ALARM SIGNAL DETECTION to OFF. If no action is performed by the user for 5 seconds, the system returns to the alarm recording mode. [ON/OFF]

②ALARM SIGNAL POLARITY

Set to N. C. (Normally Close) when the alarm input is Active High, and set to N.O.(Normally Open) when the alarm input is Active Low. [N.C./N.O.]

➂ALARM BUZZER

Set to ON to have the system activate the Buzzer when a motion is deteced in the input video or when alarm occurs, or set to OFF to keep the Buzzer inactive. [ON/OFF]

➃MAIN ALARM TIME

Set the duration for which alarm recording is to be performed when a motion is detected in the input video or when alarm occurs. The value can be set from 0 seconds to 5 minutes when you set to OFF. If you set to AUTO, the alarm recording is performed only during when the alarm signal is Active.

[5MINUTE/4MINUTE/3MINUTE/2MINUTE/1MINUTE/30SECOND/20SECOND/10SECOND/AUTO/OFF]

4-9 4-10