Specifications Specif cations Tape Roll Diameter | 3M 800ab manual

4-SPECIFICATIONS (continued)

Specif cations

6.Tape Roll Diameter

Up to 405mm [16 inch] maximum on a 76.2mm [3 inch] diameter core. (Accommodates all system roll lengths of Scotch® ﬁlm tapes.)

7.Tape Application Leg Length – Standard

70mm ± 6mm [2.75 inch ±. 25 inch ]

Tape Application Leg Length – Optional

50mm ± 6mm [2 inch ±. 25 inch]

(See "Removing Taping Heads Procedure – Changing the Tape Leg Length")

8.Box Board

Style – regular slotted containers – RSC

125 to 275 P.S.I. bursting test, single wall or double wall B or C ﬂute. 23-44 lbs. per inch of width Edge Crush Test (ECT)

9.Box Weight and Size Capacities

A.Box Weight, ﬁlled: 5 lbs.–85 lbs. [2.3 kg–38.6 kg]. Contents must support ﬂaps.

B.Box Size: Minimum Maximum

Length –		150mm [6.0 inch]	Unlimited
Width	–	115mm [4.5 inch]	545mm [21.5 inch]
Height	–	120mm [4.75 inch]	Limited by stability of box through Case Sealer

Note: The case sealer can accommodate most boxes within the size range listed above. However, if the box length (in direction of seal) to box height ratio is 0.6 or less, test run several boxes to ensure proper machine performance.

DETERMINE THE BOX LIMITATIONS BY COMPLETING THIS FORMULA:

BOX LENGTH IN DIRECTION OF SEAL	= SHOULD BE GREATER THAN 0.6
BOX HEIGHT

Any box ratio approaching this limitation should be test run to ensure performance.

800ab-NA	2010 December
	13

Image 25

3M 800ab manual Specifications Specif cations Tape Roll Diameter, Tape Application Leg Length Standard, Box Board

Contents

3M 2010 44-0009-2082-5 B121510-NA Industrial Adhesives and Tapes 3M-MaticTM800ab-NAAdjustable case sealer 3M Center, Building 220-5E-06 St. Paul, MN This page is Blank 3M 2010 44-0009-1852-2 F031008-NA This page is Blank Introduction SafetyGeneral Information This page is Blank Installation Table of Contents Shipment, Handling, and StorageSafety devices Set-Up and Adjustments This page is Blank Maintenance Table of Contents OperationAdditional Instructions Technical Documentation and Information Abbreviations and Acronyms List of ABBREVIATIONS, Acronyms Introduction 3M-MaticTM800ab Adjustable Case Sealer, TypeManufacturing Specif cations / Description / Intended Use Importance of the Manual Manual MaintenanceConsulting the Manual General Information Contents-800ab Adjustable Case Sealer General Safety Information SafetyStop Switch To reduce the risk associated with hazardous voltage To reduce the risk associated with muscle strain To reduce the risk associated with sharp blade hazardsTo reduce the risk associated with pinches hazards Operators Qualif cations Personal Safety MeasuresSee Section Number of Operators Instructions for a Safe Use of the Machine Skill 1 Machine Operator 800ab Case Sealer Components Left Front View Component Locations Safety Power Requirements SpecificationsOperating Rate Operating Conditions Box Weight and Size Capacities Specifications Specif cations Tape Roll DiameterTape Application Leg Length Standard Tape Application Leg Length Optional Set-Up Recommendations Packaging for Overseas Shipment Optional Figure SHIPMENT-HANDLING-STORAGE, TransportHandling and Transportation of Uncrated Machine Storage of the Packed or Unpacked Machine Uncrating UnpackingRemoval of Pallet Disposal of Packaging Materials M8 x 16mm Socket Head Screws Adjustable InstallationTool Kit Supplied with the Machine Machine Set-Up / Bed Height M6 Lock Nut M6 Plain Washer Inclined Roller Assembly Buff ngRoller Preliminary Electric Inspection For Three-Main Phases Only Inspection of PhasesOutboard Tape Roll Holder Machine Connection to the Mains Theory of Operation Controls Stop Switch Electric System / Circuit Breaker Safety Devices of the MachineBlade Guards Emergency Stop Button SET UP and Adjustments Operation Operation Troubleshooting Guide Problem Cause Correction This page is Blank Check Eff ciency of Safety Features Maintenance and RepairsCleaning of Machine Qualif cation Cleaning of Cutter Blade Qualif cation Box Drive Belt Left Side View Infeed End Drive Belt Replacement Drive Pulley Rings Installation Box Drive Assembly, Infeed End Drive Belt Tension Tape LEG Length Reassemble Figure Disassemble Figure 11C Master Link Mark Chain Sprocket 10 Crank/Chain Guards This page is Blank 800ab-NA December This page is Blank Case of Fire Additional Instructions Enclosures / Special Info This page is Blank Electric Diagram Technical Diagrams Label Kit Machine Model Serial Number Part Number Option/Accessory Options and Accessories This page is Blank 800ab-NA December 800ab 800ab 15407 Ref. No 3M Part No Description 800ab Front 800ab Ref. No 3M Part No Description 800ab Rear 800ab Ref. No 3M Part No Description 22 46 457 7 800ab 6174 Ref. No 3M Part No Description Optional 800ab Ref. No 3M Part No Description 410 800ab Ref. No 3M Part No Description 800ab 800ab Ref. No 3M Part No Description 800ab 6176-8 800ab 6176 Ref. No 3M Part No Description 123 800ab Ref. No 3M Part No Description This page is Blank AccuGlideTM Page Replacement Parts and Service Information To Our Customers This page is Blank 3M 2009 44-0009-1852-2 F031008 This page is Blank Dimensional Drawing AccuGlide 3 Taping Head February AccuGlide 3 Upper Taping Head 2 inch, Type Intended Use This page is Blank Updating the Manual General Information How to use this Manual To reduce the risk associated with impact hazards Them Before Installing or Operating this EquipmentTo reduce the risk associated with mechanical hazards Upper Taping Head Label Lower Taping Head Label Important Safeguards Specif cations Tape Taping Head DimensionsTape Width Box Size Capacities Dimensional Drawing Tape Width Adjustment Installation GuidelinesReceiving And Handling To reduce risk associated with muscle strain AccuGlide 3 Taping Head February Operation on next Tape Loading Lower Taping Head Tape Loading Upper Taping HeadOne-Way Tension Roller Wrap Knurled Applying AccuGlide 3 Taping Head February Blade Guard Knife Holder Guard Blade Replacement Hex Socket Section View 5mm HexRoller/Shaft Key Wrench Applying/Buff ng Roller Replacement Tape Drum Friction Brake Figure Tape Latch Alignment Figure One-Way Tension Roller Applying Mechanism Spring Changing Tape Leg Length Leading Tape Leg Length Adjustment FigurePage Page Replacement Parts and Service Spare Parts/Service Information Recommended Spare PartsQty Ref. No Part Number Description Page 10922 10923 Upper Head AccuGlide 3 Taping Head February Upper Head Ref. No 3M Part No Description Upper and Lower Heads Upper and Lower Heads Ref. No 3M Part No Description Upper Head Upper Head Ref. No 3M Part No Description Upper and Lower Heads AccuGlide 3 Taping Head August Upper and Lower Heads Ref. No 3M Part No Description AccuGlide 3 Taping Head August Upper and Lower Heads Ref. No 3M Part No Description Upper and Lower Heads AccuGlide 3 Taping Head February Latch Upper and Lower Heads Ref. No 3M Part No Description Lower Head AccuGlide 3 Taping Head February Lower Head Ref. No 3M Part No Description Lower Head Lower Head Ref. No 3M Part No Description This page is Blank