3M 2009 44-0009-1852-2 F031008 | 3M 800ab guide

Replacement Parts And Service Information

To Our Customers:

This is the 3M-Matic™/AccuGlide™/Scotch®equipment you ordered. It has been set up

and tested in the factory with Scotch® tapes. If any problems occur when operating this equipment and you desire a service call or phone consultation, call, write, or fax the appropriate number listed below.

Included with each machine is an Instructions and Parts List manual.

SERVICE, REPLACEMENT PARTS, AND ADDITIONAL MANUALS

AVAILABLE DIRECT FROM:

Order parts by part number, part description, and quantity required. Also, when ordering parts or additional manuals, include model/machine name, machine type, and serial number that are located on the identiﬁcation plate.

3M Industrial Adhesives and Tapes

3M Center, Building 220-5E-06 St. Paul, MN 55144-1000

3M-Matic™, AccuGlide™ and Scotch™ are Trade- marks of 3M, St. Paul, MN 55144-1000 Printed in U.S.A.

© 3M 2009 44-0009-1852-2 (F031008)

ii

Image 79

3M 800ab manual 3M 2009 44-0009-1852-2 F031008

Contents

3M 2010 44-0009-2082-5 B121510-NA Industrial Adhesives and Tapes 3M-MaticTM800ab-NAAdjustable case sealer 3M Center, Building 220-5E-06 St. Paul, MN This page is Blank 3M 2010 44-0009-1852-2 F031008-NA This page is Blank Introduction SafetyGeneral Information This page is Blank Set-Up and Adjustments Table of Contents Shipment, Handling, and StorageInstallation Safety devices This page is Blank Technical Documentation and Information Table of Contents OperationMaintenance Additional Instructions Abbreviations and Acronyms List of ABBREVIATIONS, Acronyms Introduction 3M-MaticTM800ab Adjustable Case Sealer, TypeManufacturing Specif cations / Description / Intended Use Importance of the Manual Manual MaintenanceConsulting the Manual General Information Contents-800ab Adjustable Case Sealer General Safety Information SafetyStop Switch To reduce the risk associated with hazardous voltage To reduce the risk associated with muscle strain To reduce the risk associated with sharp blade hazardsTo reduce the risk associated with pinches hazards Instructions for a Safe Use of the Machine Personal Safety MeasuresOperators Qualif cations See Section Number of Operators Skill 1 Machine Operator 800ab Case Sealer Components Left Front View Component Locations Safety Operating Conditions SpecificationsPower Requirements Operating Rate Tape Application Leg Length Optional Specifications Specif cations Tape Roll DiameterBox Weight and Size Capacities Tape Application Leg Length Standard Set-Up Recommendations Storage of the Packed or Unpacked Machine SHIPMENT-HANDLING-STORAGE, TransportPackaging for Overseas Shipment Optional Figure Handling and Transportation of Uncrated Machine Disposal of Packaging Materials UnpackingUncrating Removal of Pallet Machine Set-Up / Bed Height InstallationM8 x 16mm Socket Head Screws Adjustable Tool Kit Supplied with the Machine M6 Lock Nut M6 Plain Washer Inclined Roller Assembly Buff ngRoller Machine Connection to the Mains Inspection of PhasesPreliminary Electric Inspection For Three-Main Phases Only Outboard Tape Roll Holder Theory of Operation Controls Emergency Stop Button Safety Devices of the MachineStop Switch Electric System / Circuit Breaker Blade Guards SET UP and Adjustments Operation Operation Troubleshooting Guide Problem Cause Correction This page is Blank Cleaning of Cutter Blade Qualif cation Maintenance and RepairsCheck Eff ciency of Safety Features Cleaning of Machine Qualif cation Box Drive Belt Left Side View Infeed End Drive Belt Replacement Drive Pulley Rings Installation Box Drive Assembly, Infeed End Drive Belt Tension Tape LEG Length Reassemble Figure Disassemble Figure 11C Master Link Mark Chain Sprocket 10 Crank/Chain Guards This page is Blank 800ab-NA December This page is Blank Case of Fire Additional Instructions Enclosures / Special Info This page is Blank Electric Diagram Technical Diagrams Label Kit Machine Model Serial Number Part Number Option/Accessory Options and Accessories This page is Blank 800ab-NA December 800ab 800ab 15407 Ref. No 3M Part No Description 800ab Front 800ab Ref. No 3M Part No Description 800ab Rear 800ab Ref. No 3M Part No Description 22 46 457 7 800ab 6174 Ref. No 3M Part No Description Optional 800ab Ref. No 3M Part No Description 410 800ab Ref. No 3M Part No Description 800ab 800ab Ref. No 3M Part No Description 800ab 6176-8 800ab 6176 Ref. No 3M Part No Description 123 800ab Ref. No 3M Part No Description This page is Blank AccuGlideTM Page Replacement Parts and Service Information To Our Customers This page is Blank 3M 2009 44-0009-1852-2 F031008 This page is Blank Dimensional Drawing AccuGlide 3 Taping Head February AccuGlide 3 Upper Taping Head 2 inch, Type Intended Use This page is Blank Updating the Manual General Information How to use this Manual To reduce the risk associated with impact hazards Them Before Installing or Operating this EquipmentTo reduce the risk associated with mechanical hazards Upper Taping Head Label Lower Taping Head Label Important Safeguards Box Size Capacities Taping Head DimensionsSpecif cations Tape Tape Width Dimensional Drawing To reduce risk associated with muscle strain Installation GuidelinesTape Width Adjustment Receiving And Handling AccuGlide 3 Taping Head February Operation on next Tape Loading Lower Taping Head Tape Loading Upper Taping HeadOne-Way Tension Roller Wrap Knurled Applying AccuGlide 3 Taping Head February Blade Guard Knife Holder Guard Blade Replacement Hex Socket Section View 5mm HexRoller/Shaft Key Wrench Applying/Buff ng Roller Replacement Tape Drum Friction Brake Figure Tape Latch Alignment Figure One-Way Tension Roller Applying Mechanism Spring Changing Tape Leg Length Leading Tape Leg Length Adjustment FigurePage Page Replacement Parts and Service Spare Parts/Service Information Recommended Spare PartsQty Ref. No Part Number Description Page 10922 10923 Upper Head AccuGlide 3 Taping Head February Upper Head Ref. No 3M Part No Description Upper and Lower Heads Upper and Lower Heads Ref. No 3M Part No Description Upper Head Upper Head Ref. No 3M Part No Description Upper and Lower Heads AccuGlide 3 Taping Head August Upper and Lower Heads Ref. No 3M Part No Description AccuGlide 3 Taping Head August Upper and Lower Heads Ref. No 3M Part No Description Upper and Lower Heads AccuGlide 3 Taping Head February Latch Upper and Lower Heads Ref. No 3M Part No Description Lower Head AccuGlide 3 Taping Head February Lower Head Ref. No 3M Part No Description Lower Head Lower Head Ref. No 3M Part No Description This page is Blank