Operation Troubleshooting Guide Problem Cause Correction | 3M 800ab

12-OPERATION (continued)

12.9 Troubleshooting Guide
Problem	Cause	Correction
Drive belts do not convey boxes	Narrow boxes	Check machine speciﬁcations.
		Boxes are narrower than
		recommended, causing slippage
		and premature belt wear.
	Worn drive belts	Replace drive belts
	Top taping head does not apply	Adjust the box height adjustment
	enough pressure	with the crank
	Top ﬂap compression rollers in too	Readjust compression rollers
	tight
	Taping head applying spring	Replace spring holder
	holder missing
	Taping head applying spring set	Reduce spring pressure
	too high

Drive belts do not turn	Worn or missing friction rings	Replace friction rings
	Drive belt tension too low	Adjust belt tension
	Electrical disconnect	Check power and electrical plug
	Motor not turning	Evaluate problem and correct

Drive belt break	Worn belt	Replace belt
	Excessive belt tension	Tension to 3.5 kg [7 lbs] per
		adjustment section

Tape not centered on box seam	Tape drum not centered	Reposition tape drum
	Box ﬂaps not of equal length	Check box speciﬁcations

800ab-NA

2010 December

25

Image 37

3M 800ab manual Operation Troubleshooting Guide Problem Cause Correction

Contents

3M 2010 44-0009-2082-5 B121510-NA Industrial Adhesives and Tapes 3M-MaticTM800ab-NAAdjustable case sealer 3M Center, Building 220-5E-06 St. Paul, MN This page is Blank 3M 2010 44-0009-1852-2 F031008-NA This page is Blank Introduction SafetyGeneral Information This page is Blank Installation Table of Contents Shipment, Handling, and StorageSafety devices Set-Up and Adjustments This page is Blank Maintenance Table of Contents OperationAdditional Instructions Technical Documentation and Information Abbreviations and Acronyms List of ABBREVIATIONS, Acronyms Introduction 3M-MaticTM800ab Adjustable Case Sealer, TypeManufacturing Specif cations / Description / Intended Use Importance of the Manual Manual MaintenanceConsulting the Manual General Information Contents-800ab Adjustable Case Sealer General Safety Information SafetyStop Switch To reduce the risk associated with hazardous voltage To reduce the risk associated with muscle strain To reduce the risk associated with sharp blade hazardsTo reduce the risk associated with pinches hazards Operators Qualif cations Personal Safety MeasuresSee Section Number of Operators Instructions for a Safe Use of the Machine Skill 1 Machine Operator 800ab Case Sealer Components Left Front View Component Locations Safety Power Requirements SpecificationsOperating Rate Operating Conditions Box Weight and Size Capacities Specifications Specif cations Tape Roll DiameterTape Application Leg Length Standard Tape Application Leg Length Optional Set-Up Recommendations Packaging for Overseas Shipment Optional Figure SHIPMENT-HANDLING-STORAGE, TransportHandling and Transportation of Uncrated Machine Storage of the Packed or Unpacked Machine Uncrating UnpackingRemoval of Pallet Disposal of Packaging Materials M8 x 16mm Socket Head Screws Adjustable InstallationTool Kit Supplied with the Machine Machine Set-Up / Bed Height M6 Lock Nut M6 Plain Washer Inclined Roller Assembly Buff ngRoller Preliminary Electric Inspection For Three-Main Phases Only Inspection of PhasesOutboard Tape Roll Holder Machine Connection to the Mains Theory of Operation Controls Stop Switch Electric System / Circuit Breaker Safety Devices of the MachineBlade Guards Emergency Stop Button SET UP and Adjustments Operation Operation Troubleshooting Guide Problem Cause Correction This page is Blank Check Eff ciency of Safety Features Maintenance and RepairsCleaning of Machine Qualif cation Cleaning of Cutter Blade Qualif cation Box Drive Belt Left Side View Infeed End Drive Belt Replacement Drive Pulley Rings Installation Box Drive Assembly, Infeed End Drive Belt Tension Tape LEG Length Reassemble Figure Disassemble Figure 11C Master Link Mark Chain Sprocket 10 Crank/Chain Guards This page is Blank 800ab-NA December This page is Blank Case of Fire Additional Instructions Enclosures / Special Info This page is Blank Electric Diagram Technical Diagrams Label Kit Machine Model Serial Number Part Number Option/Accessory Options and Accessories This page is Blank 800ab-NA December 800ab 800ab 15407 Ref. No 3M Part No Description 800ab Front 800ab Ref. No 3M Part No Description 800ab Rear 800ab Ref. No 3M Part No Description 22 46 457 7 800ab 6174 Ref. No 3M Part No Description Optional 800ab Ref. No 3M Part No Description 410 800ab Ref. No 3M Part No Description 800ab 800ab Ref. No 3M Part No Description 800ab 6176-8 800ab 6176 Ref. No 3M Part No Description 123 800ab Ref. No 3M Part No Description This page is Blank AccuGlideTM Page Replacement Parts and Service Information To Our Customers This page is Blank 3M 2009 44-0009-1852-2 F031008 This page is Blank Dimensional Drawing AccuGlide 3 Taping Head February AccuGlide 3 Upper Taping Head 2 inch, Type Intended Use This page is Blank Updating the Manual General Information How to use this Manual To reduce the risk associated with impact hazards Them Before Installing or Operating this EquipmentTo reduce the risk associated with mechanical hazards Upper Taping Head Label Lower Taping Head Label Important Safeguards Specif cations Tape Taping Head DimensionsTape Width Box Size Capacities Dimensional Drawing Tape Width Adjustment Installation GuidelinesReceiving And Handling To reduce risk associated with muscle strain AccuGlide 3 Taping Head February Operation on next Tape Loading Lower Taping Head Tape Loading Upper Taping HeadOne-Way Tension Roller Wrap Knurled Applying AccuGlide 3 Taping Head February Blade Guard Knife Holder Guard Blade Replacement Hex Socket Section View 5mm HexRoller/Shaft Key Wrench Applying/Buff ng Roller Replacement Tape Drum Friction Brake Figure Tape Latch Alignment Figure One-Way Tension Roller Applying Mechanism Spring Changing Tape Leg Length Leading Tape Leg Length Adjustment FigurePage Page Replacement Parts and Service Spare Parts/Service Information Recommended Spare PartsQty Ref. No Part Number Description Page 10922 10923 Upper Head AccuGlide 3 Taping Head February Upper Head Ref. No 3M Part No Description Upper and Lower Heads Upper and Lower Heads Ref. No 3M Part No Description Upper Head Upper Head Ref. No 3M Part No Description Upper and Lower Heads AccuGlide 3 Taping Head August Upper and Lower Heads Ref. No 3M Part No Description AccuGlide 3 Taping Head August Upper and Lower Heads Ref. No 3M Part No Description Upper and Lower Heads AccuGlide 3 Taping Head February Latch Upper and Lower Heads Ref. No 3M Part No Description Lower Head AccuGlide 3 Taping Head February Lower Head Ref. No 3M Part No Description Lower Head Lower Head Ref. No 3M Part No Description This page is Blank