Manuals / A&D / Personal Care / Scale

A&D EJ-6100, EJ-440, EJ-3000, EJ-200, EJ-120 2000, 1751, 8801, Place a sample on the upper pan

Models: EJ-4100

1 42

Download 42 pages 61.46 Kb

Page 31

Image 31

2.Place a sample on the upper pan.

3.Wait for the STABLE indicator to be displayed and press the SAMPLE key to store the weight in air.

4.The display shows that LO blinks and the balance starts to measure weight in water.

5.Place the sample on the lower pan in water.

Adjust the amount of water so that the sample is about 10 mm below water surface.

6.Wait for the STABLE indicator to be displayed and press the SAMPLE key. Then the balance reads the weight in water and shows the density (specific gravity) of the sample.

7.To continue the specific gravity measurement, press the SAMPLE key again. To exit this measurement, press the UNITS key.

HI SG

2000.

Measuring weight in water.

LO SG

2000.

LO SG

1751.

8801.

The display shows the density.

To weigh in air.

To weigh in water.

Page 31

Image 31

A&D EJ-6100, EJ-440, EJ-3000, EJ-4100, EJ-120, EJ-2000, EJ-1500 manual 1751, 8801, Place a sample on the upper pan

Contents

1WMPD4001917 Compliance with FCC rules This manual and MarksCopyright2009 CONTENTS 11-1 11. MAINTENANCE12. SPECIFICATIONS GRAVITY ACCELERATION MAP2. UNPACKING 1. INTRODUCTION3. PART NAMES AND FUNCTIONS NET indicatorWhen using the AC adapter 4. SETTING UP4-1. Setting up your balance 4-2. Power source4-4. Storage 4-3. Breeze breakInstalling batteries 5-2. LCD backlight 5-1. Turn the power ON and OFF‰ Auto-power off function 5. OPERATION‰ Note 5-3. UnitsConversion table 5-4. Selecting a weighing unit Precautions during operation5-5. Basic operation Storing the sample unit 5-6. Counting mode pcsSelecting the counting mode Counting mode using the ACAI function758. % 5-7. Percent mode %100 0 % 1000. %poff 6-1. Setting example6. COMPARATOR funcCp lo Cp Hi000000 0012347. CALIBRATION 7-1. Calibration using a weight060000 0end000 Cal 5000050000 0end0007-2. Gravity acceleration correction Cal 97985‰ Note func 8-2. Entering the function setting mode8. FUNCTIONS 8-1. Key operationend Cp Hi 8-3. Setting examplefunc poff aCaifunc Unitend id 8-4. Storing weighing units8-5. Function list Class 9-2. EJ-03 RS-232C serial interface EJ-03 Installation9. OPTIONS 9-1. EJ-02 USB Interface1 -15V~-5V 0 5V~15V Interface specificationsData format Data output modeCommand list Command mode9-5. EJ-12 Carrying case EJ-07 / EJ-08 Installation9-3. EJ-07 / EJ-08 Underhook 9-4. EJ-11 Breeze break9-6. EJ-13 Density Determination Kit EJ-13 InstallationDensity specific gravity measurement d10000 t---25Change the function table Example of density measurement2000 20001751 8801end id func 10-1. Setting the ID number10. ID NUMBER AND GLP id 000000Data format for “calibration report” 10-2. Output exampleData format for “calibration test report” block 10-3. Calibration test using a weightTitle End block20000 20000 end 20000eeeeee 11. MAINTENANCE11-1. Notes on maintenance 11-2. Error codesHb1 lb1 error1Cal e -Cal e lb0 Hb012-1. EJ series 12. SPECIFICATIONS12-2. Other weighing units 12-3. Options 12-4. Dimensionsφ115 Values of gravity at various locations GRAVITY ACCELERATION MAPWorld map