Installing the Server into a Telco Rack | Acnodes RMC 7182 specs

RMC 7182

1U Rackmount System

Installing the Server into a Telco Rack

To install the Acnodes RMC7182 into a Telco type rack, use two L-shaped brackets on either side of the chassis (four total). First, determine how far follow the server will extend out the front of the rack. Larger chassis should be positioned to balance the weight between front and back. If a bezel is included on your server, remove it. Then attach the two front brackets to each side of the chassis, then the two rear brack- ets positioned with just enough space to accommodate the width of the telco rack. Finish by sliding the chassis into the rack and tightening the brackets to the rack.

	© Copyright 2009 Acnodes, Inc.
661 Brea Canyon Rd., Suite 3	All rights reserved. Product description and product specifications
Walnut, CA 91789	are subject to change without notice. For latest product information,
tel: 909.598.7388, fax: 909.598.0218	please visit Acnodes’ web site at www.acnodes.com.

Image 23

Acnodes RMC 7182 user manual Installing the Server into a Telco Rack

Contents

RMC Copyright 2005 Acnodes, Inc Manual Organization Preface Bios Advanced Motherboard SetupAdvanced Chassis Setup Table of Contents System Interface Installing the System in to a Rack Advanced Motherboard Setup NIC2 JLAN2 LED NIC1 JLAN1 LED Advanced Chassis Setup Bios Overview Introduction Memory Motherboard FeaturesOther Features Processor RMC Control Panel Server Chassis FeaturesSystem Power Sata Subsystem Unpacking the System Choosing a Setup LocationPreparing for Setup Overview Server Precautions Rack Precautions Rack Mounting Considerations Identifying the Sections of the Rack Rails Installing the System into a Rack Inner Rails Installing the Rack Rails Outer Rails RMC Installing the Chassis into a Rack Installing the Server into a Telco Rack Checking the Components Checking the Motherboard SetupRemoving the Chassis Cover Figure Checking the Airflow Checking the Drive Bay SetupProviding Power Checking the Drives Control Panel Buttons Reset ButtonPower Universal Information LED Control Panel LEDs NIC2 Drive Carrier LEDs Electrical Safety Precautions System Safety General Safety Precautions ESD Precautions Operating Precautions Handling the Motherboard Precautions Unpacking Serverboard InstallationInstalling to the Chassis Connecting the Control Panel Connecting CablesConnecting Data Cables Connecting Power Cables I/O Ports Installing an LGA1366 Processor Installing the Processor and Heatsink RMC Installing a Passive CPU Heatsink Removing the Heatsink Installing & Removing DIMMs Installing Memory Modules Maximum Memory Possible Memory Support PCI Expansion Cards Installing a PCI Expansion Card Serverboard Details RMC Power Button Connector DefinitionsMain ATX Power Supply Connector Processor Power Connector Overheat/Fan Fail/UID LED HDD LED/UID SwitchPower On LED Serial Ports NMI ButtonFan Headers ATX PS/2 Keyboard and PS/2 Mouse Ports Overheat/Fan Fail LED Chassis IntrusionWake-On-LAN External Speaker/Internal Buzzer Sgpio Headers Onboard Power LEDPower Supply SMBus Connector Universal Serial Bus USB Unit Identifier Button Power Supply Fail LED HeaderAlarm Reset Button Cmos Clear Jumper SettingsVGA Enable/Disable Explanation of Jumpers USB Wake-Up LAN1/2 Enable/DisableWatch Dog Enable/Disable SMBus to PCI Slots BMC Enable/DisableSAS Enable/Disable SAS RAID Mode Select Ipmi Dedicated LAN LEDs Onboard IndicatorsOnboard Power LED LE1 LAN1/2 LEDs SAS Heartbeat LED BMC Heartbeat LEDSAS Activity LED SAS Ports Floppy ConnectorSata and Floppy Drive Connections Sata Ports Driver/Tool Installation Display Screen Installing Software RMC RMC Tools Required Static-Sensitive Devices System Cooling Control Panel Replacing a System Fan Figure Adding a System FanSystem Fan Failure Installing a Hard Drive into a Drive Carrier Figure Drive Bay Installation/RemovalAccessing the Drive Bays Hard Drive Installation Removing a Hard Drive Figure DVD Drive Installation Power Supply Failure Power Supply Removing/Replacing the Power Supply Introduction Starting Bios Setup UtilityHow To Change the Configuration Data Starting the Setup Utility Main Setup System Memory System Time/System Date AddOn ROM Display Mode Advanced Setup ConfigurationsXboot Features Quick Boot Quiet Boot PS/2 Mouse Support Wait For F1 If ErrorPower Button Function Restore on AC Power Loss Clock Spread Spectrum Ratio Cmos SettingHardware Prefetcher Available when supported by the CPU XProcessor & Clock Options CPU Ratio Intel Eist Technology Active Processor Cores TDC Limit Override Intel Turbo Boost Configuration Turbo Ratio Limit ProgramCore Ratio Limit ~ 3 Core Ratio Limit XAdvanced Chipset Control Memory Frequency Memory ModeTemperature Rise QPI L0s and L1 Dimm Pitch High Performance Event TimerAir Flow Altitude Xide / Floppy Configuration Type IDE Detect Timeout secLBA/Large Mode Block Multi-Sector Transfer PIO ModeDMA Mode 32Bit Data Transfer A.R.T. For Hard disk drives XPCI/PnP Configuration XRemote Access Configuration XSuper IO Device Configuration XHardware Health Configuration CPU Temperature System Temperature USB Device WakeUp Xacpi ConfigurationFan Speed Control Modes Fan1 ~ Fan 5 Reading TPM Enable/Disable Status Headless ModeAcpi Version Features XTrusted Computing TCG/TPM Support Execute TPM Command Xipmi Configuration BMC Watch Dog Timer Action Set PEF Configuration Mark all events as read XEvent Log ConfigurationBMC WatchDog TimeOut MinSec View Event Log Change Supervisor Password Security SettingsSupervisor Password User Password Boot Sector Virus Protection Change User Password XHard Disk Drives Boot SettingsXBoot Device Priority Save Changes and Exit Retry Boot DevicesExit Options XRemovable Drives Discard Changes Load Optimal DefaultsLoad Fail-Safe Defaults Discard Changes and Exit Recoverable Post Error Beep Codes Appendix a Post Error Beep Codes Installing Windows on RAID Systems Appendix B Installing the Windows OS Installing Windows on Non-RAID Systems SAS Controller ProcessorsChipset Memory Capacity System Cooling WeightPower Supply Chassis