Manuals / Brands / Computer Equipment / Server / ADTRAN / Computer Equipment / Server

ADTRAN MP-114, MP-118 3.1.4 Searching for ini file Parameters

1 44

Download 44 pages, 1.83 Mb

Quick Installation Guide 3. Configuring the MediaPack

Version 5.0 13 September 2007

3.1.4 Searching for ini file Parameters

The Embedded Web Server provides a search engine that allows you to search any ini file

parameter that is configurable using the Embedded Web Server. The search result provides you

with a link to the relevant Web page in which the parameter appears. You can search for a

specific parameter (e.g., 'EnableIPSec') or a sub-string of that parameter (e.g., 'sec'). If you

search for a sub-string, the Embedded Web Server lists all found parameters that contain the

searched sub-string in their parameter names. The Search button, located near the bottom of the

Main menu bar is used to perform parameter searches.

¾ To search for an ini file parameter configurable by the Embedded Web

Server, take these 3 steps:

1. In the 'Search' field, enter the required name or sub-string of the ini file parameter.

2. Click Search; the 'Searched Result' screen appears listing all searched parameter results:

Figure 3-4: Searched Result Screen

3. In the Searched Result list, click the required parameter to open the screen in which the

parameter appears. In the relevant screen, the searched parameter is highlighted in green

for easy identification, as shown in the figure below.

Figure 3-5: Searched Parameter Highlighted in Screen

Note: If the searched parameter is not located, the "No Matches Found For This String"

message is displayed.

1

2

Contents

Main Page Table of Contents Page Notices Notice Trademarks WEEE EU Directive Customer Support Abbreviations and Terminology Related Documentation 1 Introduction Page 2 Quick Start 3 Configuring the MediaPack 3.1 Embedded Web Server Management Tool 3.1.1 Accessing the Embedded Web Server To access the Embedded Web Server, take these 4 steps: Page 3.1.3 Changing Login Username and Password To change the user name and password, take these 3 steps: 3.1.4 Searching for ini file Parameters To search for an ini file parameter configurable by the Embedded Web Server, take these 3 steps: 3.2 Assigning an IP Address to the MediaPack 3.2.1 Assigning an IP Address using BootP To assign an IP address using BootP, take these 3 steps: 3.2.2 Assigning an IP Address Using CLI via RS-232 To assign an IP address using CLI via RS-232, take these 5 steps: 3.2.3 Assigning an IP Address using HTTP To assign an IP address to the gateway using HTTP, take these 5 steps: 3.3 Advanced Configuration 3.3.1 Using the ini File 3.3.1.1 Obtaining the ini File from the Web To download the ini file to your PC, take these 4 steps: 3.3.1.2 Uploading the ini File to the Gateway To upload the ini file to the gateway, take these 6 steps: 3.3.1.3 Modifying Parameters Specific to Site Deployment 3.3.2 Using the Embedded Web Server 3.3.2.1 Defining Mediation Server's IP Address To define Mediation Server's IP address, take these 4 steps: 3.3.2.2 Defining Number of FXO Ports Connected to PBX To enable the gateway's FXO ports, take these 4 steps: 3.3.2.3 Defining Voice Coders To define the coder, take these 3 steps: 3.3.2.4 Translating Numbers From / To E.164 Using Manipulation Tables for PBX/PSTN Connectivity To configure the Number Manipulation tables, take these 4 steps: 3.3.2.4.1 Dialing Plan Notation 3.3.2.4.2 Number Normalization Examples Page 3.3.2.5 Defining Answer Supervision To define the Answer Supervision, take these 3 steps: Page 3.3.2.7 Enabling Caller ID To enable Caller ID, take these 3 steps: Page 3.3.2.9 Defining Disconnect on Broken Connection To define Disconnect on Broken Connection, take these 3 steps: 3.3.2.10 Defining DTMF Payload Type To define the DTMF payload type, take these 3 steps: 3.3.2.11 Enabling One-Stage Dialing To enable one-stage dialing, take these 3 steps: 3.3.2.12 Defining Channel Select Mode To define the Channel Select mode, take these 3 steps: 3.3.2.13 Disabling RTCP Attribute To disable the RTCP attribute, take these 5 steps: 4 Backing Up Configuration Settings To save the ini file on your PC, take these 6 steps: 5 Monitoring the Gateway 5.1 Front-Panel LEDs 5.2 Monitoring the Channels To monitor the status of the channels, take this step: To monitor the details of a channel, take these 2 steps: 6 Troubleshooting 6.1 General Troubleshooting 6.2 Restoring Parameters to Factory Default Settings To restore factory default settings, take these 3 steps: 6.3 Debugging using a Syslog Server To configure the Syslog parameters, take these 7 steps: MP-11x & Microsoft Office Communications Server 2007 Quick Installation Guide 42 Document #: LTRT-26301 7 Regulatory Information Declaration of Conformity Quick Installation Guide 7. Regulatory Information Safety Industry Canada Notice Network Compatibility Telecommunication Safety SELV: Safety extra low voltage circuit.