Quick Start, Required Steps to Install MediaPack | ADTRAN MP-114

Quick Installation Guide

2. Quick Start

2 Quick Start

This Quick Installation Guide helps you setup the MediaPack gateways for interoperability with either third-party PBXs or various PSTN interfaces, and Office Communications Server 2007. Prior knowledge of IP networks is recommended.

Figure 2-1: Required Steps to Install MediaPack

Refer to Section 3.2

Refer to Section 3.3.1

Refer to Section 3.3.2

Refer to Section 3.3.1.1

Refer to Section 3.3.1.2

Refer to Section 3.3.1.3

Note: For detailed information on how to fully configure the gateway, refer to the MediaPack User’s Manuals.

Version 5.0

9

September 2007

Image 9

ADTRAN MP-114, MP-118 manual Quick Start, Required Steps to Install MediaPack

Contents

MediaPack MP-118 & MP-114 Page Table of Contents Readers Notes Weee EU Directive TrademarksCustomer Support Abbreviations and Terminology Document # Manual Name Related Documentation Network Architecture with PBX Introduction MP-11x & Microsoft Office Communications Server Quick Start Required Steps to Install MediaPack Accessing the Embedded Web Server Configuring the MediaPack¾ To access the Embedded Web Server, take these 4 steps Embedded Web Server Management Tool MediaPack Web Interface Areas Navigating the Embedded Web Server ¾ To change the user name and password, take these 3 steps Changing Login Username and Password Searched Result Screen Searching for ini file Parameters ¾ To assign an IP address using BootP, take these 3 steps Assigning an IP Address using BootPAssigning an IP Address to the MediaPack New Client button Adding a BootP Client Assigning an IP Address Using CLI via RS-232 Quick Setup Screen Assigning an IP Address using Http Advanced Configuration Using the ini FileObtaining the ini File from the Web ¾ To download the ini file to your PC, take these 4 steps Uploading the ini File to the Gateway¾ To upload the ini file to the gateway, take these 6 steps Modifying Parameters Specific to Site Deployment Configuration File Screen Defining Mediation Servers IP Address Using the Embedded Web Server ¾ To define Mediation Servers IP address, take these 4 steps Defining Number of FXO Ports Connected to PBX ¾ To enable the gateways FXO ports, take these 4 steps ¾ To define the coder, take these 3 steps Defining Voice Coders Parameter Description Number Manipulation Parameters Description Source IP Dialing Plan Notations Description Example Number Normalization Examples 14 Phone Number Manipulation Table for TelÆIP Calls ¾ To define the Answer Supervision, take these 3 steps Defining Answer Supervision ¾ To define Automatic Dialing, take these 4 steps Defining Automatic Dialing Enabling Caller ID ¾ To enable Caller ID, take these 3 steps ¾ To define the SIP transport type, take these 3 steps Defining SIP Transport Type 19 General Parameters Screen Defining Disconnect on Broken Connection ¾ To define the Dtmf payload type, take these 3 steps Defining Dtmf Payload Type Enabling One-Stage Dialing ¾ To enable one-stage dialing, take these 3 steps ¾ To define the Channel Select mode, take these 3 steps Defining Channel Select Mode Disabling Rtcp Attribute ¾ To disable the Rtcp attribute, take these 5 steps ¾ To save the ini file on your PC, take these 6 steps Backing Up Configuration Settings Front-Panel LEDs Monitoring the Gateway Monitoring the Channels ¾ To monitor the status of the channels, take this step¾ To monitor the details of a channel, take these 2 steps General Troubleshooting TroubleshootingRestoring Parameters to Factory Default Settings Debugging using a Syslog Server Management Settings Screen ¾ To configure the Syslog parameters, take these 7 steps Regulatory Information Industry Canada Notice Telecommunication SafetyNetwork Compatibility FCC Statement MediaPack MP-118 & MP-114