Defining Disconnect on Broken Connection | ADTRAN MP-118, MP-114

MP-11x & Microsoft Office Communications Server 2007

3.3.2.9Defining Disconnect on Broken Connection

The procedure below describes how to configure the Disconnect on Broken Connection parameter. Since Mediation Server uses Silence Suppression, it may not send Real-time Transport Protocol (RTP) packets during the detection of silence in the call. To avoid call disconnection by the gateway (due to RTP packets not being transmitted), you may need to disable the parameter 'Disconnect on Broken Connection'.

¾To define Disconnect on Broken Connection, take these 3 steps:

1.Open the ‘General Parameters’ screen (Protocol Management menu > Advanced Parameters > General Parameters).

Figure 3-19: General Parameters Screen

2

2.From the ‘Disconnect on Broken Connection’ drop-down list, select ‘No’.

3.Click the Submit button to save your changes.

Quick Installation Guide

32

Document #: LTRT-26301

Image 32

ADTRAN MP-118, MP-114 manual Defining Disconnect on Broken Connection, General Parameters Screen

Contents

MediaPack MP-118 & MP-114 Page Table of Contents Readers Notes Trademarks Weee EU DirectiveCustomer Support Abbreviations and Terminology Related Documentation Document # Manual Name Introduction Network Architecture with PBX MP-11x & Microsoft Office Communications Server Required Steps to Install MediaPack Quick Start Configuring the MediaPack Accessing the Embedded Web Server¾ To access the Embedded Web Server, take these 4 steps Embedded Web Server Management Tool Navigating the Embedded Web Server MediaPack Web Interface Areas Changing Login Username and Password ¾ To change the user name and password, take these 3 steps Searching for ini file Parameters Searched Result Screen Assigning an IP Address using BootP ¾ To assign an IP address using BootP, take these 3 stepsAssigning an IP Address to the MediaPack New Client button Assigning an IP Address Using CLI via RS-232 Adding a BootP Client Assigning an IP Address using Http Quick Setup Screen Obtaining the ini File from the Web Advanced ConfigurationUsing the ini File ¾ To upload the ini file to the gateway, take these 6 steps ¾ To download the ini file to your PC, take these 4 stepsUploading the ini File to the Gateway Configuration File Screen Modifying Parameters Specific to Site Deployment Using the Embedded Web Server Defining Mediation Servers IP Address ¾ To define Mediation Servers IP address, take these 4 steps ¾ To enable the gateways FXO ports, take these 4 steps Defining Number of FXO Ports Connected to PBX Defining Voice Coders ¾ To define the coder, take these 3 steps Number Manipulation Parameters Description Parameter Description Dialing Plan Notations Description Example Source IP Number Normalization Examples 14 Phone Number Manipulation Table for TelÆIP Calls Defining Answer Supervision ¾ To define the Answer Supervision, take these 3 steps Defining Automatic Dialing ¾ To define Automatic Dialing, take these 4 steps ¾ To enable Caller ID, take these 3 steps Enabling Caller ID Defining SIP Transport Type ¾ To define the SIP transport type, take these 3 steps Defining Disconnect on Broken Connection 19 General Parameters Screen Defining Dtmf Payload Type ¾ To define the Dtmf payload type, take these 3 steps ¾ To enable one-stage dialing, take these 3 steps Enabling One-Stage Dialing Defining Channel Select Mode ¾ To define the Channel Select mode, take these 3 steps ¾ To disable the Rtcp attribute, take these 5 steps Disabling Rtcp Attribute Backing Up Configuration Settings ¾ To save the ini file on your PC, take these 6 steps Monitoring the Gateway Front-Panel LEDs ¾ To monitor the details of a channel, take these 2 steps Monitoring the Channels¾ To monitor the status of the channels, take this step Troubleshooting General TroubleshootingRestoring Parameters to Factory Default Settings Debugging using a Syslog Server ¾ To configure the Syslog parameters, take these 7 steps Management Settings Screen Regulatory Information Telecommunication Safety Industry Canada NoticeNetwork Compatibility FCC Statement MediaPack MP-118 & MP-114